Integra DTR-7 Using a Macro function, Open the battery cover and remove the batteries

Page 57

1.Open the battery cover and remove the batteries.

Using a Macro function

Erasing all codes and operations programmed in the buttons

This procedure will erase all remote controller codes for the other devices and all macro operations that have been programmed in the RC-392M (see pages 52, 54 and 55).

1.Open the battery cover and remove the batteries.

2.While pressing and holding down the POWER ON button and the POWER STNBY button, insert the batteries in the correct direction.

After inserting the batteries, release the buttons. The SEND/ LEARN indicator flashes slowly.

3.Press the ENT button.

The SEND/LEARN indicator lights up for about ten seconds, then turns off.

All programmed codes are erased and the button memories re- turn to the factory presets.

Notes:

•Proceed to Step 3 immediately once you have completed Step 2. Other- wise, the batteries will be consumed quickly.

•If you press any button other than the ENT button in Step 3, no codes will be erased. In this case, repeat the steps from the beginning.

Image 57

Contents Preparation Before usingOperation AppendixAVIS Important Safeguards1. Warranty Claim Precautions5.Power Note to CATV system installerSupplied accessories FeaturesKey Features Aluminum volume controlBefore operating this unit Installing the remote controller batteriesUsing the remote controller Do not plug in the power Audio equipment connectionscord until all connections have been madeAudio equipment connections Connections for remote control zAC outlet connection Video equipment connections Video equipment connections Connecting equipment with 5.1-channeloutputDecoder with 5.1-channeloutput Speaker placement Connecting speakersFRONT SPEAKERS Connecting speakersSURROUND SPEAKERS CENTER SPEAKERConnecting speakers Connecting power amplifiersConnecting a subwoofer Connecting power amplifiersConnecting the power Connecting an equalizer DTR-7Connecting a power cable Connecting the powerConnecting the antenna cable Making antenna connectionsDirectional Iinkage Assembling the AM loop antennaConnecting the included antennas Making antenna connectionsConnecting an FM outdoor antenna Connecting an AM outdoor antennaUsing the on-screendisplay How to use the on-screendisplayScreen Setup OSD screens Using the on-screendisplayFront Setting the speaker configurationCenter Surround Setting the speaker configuration parametersUsing the on-screendisplay Setting the speaker configurationSetting the speaker distance Using the on-screendisplayLoudspeaker Position Time Synchronization Center Setting the speaker LevelRight R-SurSetting the Speaker level Setting the bass peak levelBass Peak Level Manager* DTR-7only Setting the Speaker level Playing a digital source Digital Input SetupUsing the on-screendisplay Digital input setupTuning in a radio station Presetting FM/AM radio stationsPresetting FM/AM radio stations Cancelling preset stationsProgramming radio stations 3. Start playing the selected input source Selecting an input sourceSelecting an input source Selecting an input source Using the on-screendisplay Digital Input SetupSelecting an input source COAXIALSelecting an input source Selecting the speaker systemChanging the display Selecting an input source Adjusting the tone Bass and treble adjustmentUsing the on-screendisplay Selecting a preset stationPlaying a multichannel input source Setting the MULTI CHANNEL INPUTUsing the on-screendisplay Before Using Listening Mode Using the Listening ModesDSP Digital Signal Processor Listening Modes3. MASTER VOLUME control knob Using the listening modes3. VOLUME buttons 2. Listening mode buttonUsing the listening modes Using the listening modesInput sources and listening modes Using the listening modesSetting the listening mode parameters How to set the listening mode parametersUsing the on-screendisplay Listening mode parameters Setting the listening mode parametersRe-EQCinema Re-Equalization Late NightVideo Assign Setup Video Assign SetupUsing the on-screendisplay PHONOGiving a name to each input source Giving a name to each preset radio stationTo change a name To erase a nameTo use the above setting from now on Fine-tuningthe output level of each speaker1.Press the CH LEVEL button 3.Repeat the operation described in stepVolume display method setup Other setup operationsIntelliVolume setup Using the on-screendisplaymovie Recording a source while listening to music or aRecording from on audio /video source Recording a sourceRecording a source Using the on-screendisplayAdding sound to a video tape Using Multi-RoomRemote System Outline of Multi-roomRemote SystemEnjoying Music and Movies in the Sub-room Enjoying Music and Movies in the Sub-room When the system is mounted in a rackTo control the system in the sub-room Initial settings The initial settingsConfig Setup Distance SetupUsing the RC-392Mto control each device Using the remote controllerTurning the power on and off to the receiver indicatorUsing the remote controller Controlling an Onkyo/Integra CD playerControlling an Onkyo/Integra DVD player Controlling an Onkyo/Integra MD recorder Using the remote controllerControlling an Onkyo/Integra tape deck MODE SAT, CABLE, VCR, and TV buttonsProgramming procedure Erasing a learned code from a MODE button Erasing a learned code2 1 Using a Macro functionWhat is a Macro function? Programming Macro modeMacro Direct Learning function Using a Macro functionUsing a Macro function Using a Macro function 1.Open the battery cover and remove the batteries3.Press the ENT button Trouble Troubleshooting guideCause RemedyFM/AM Troubleshooting guideVideo & audio OthersSpecifications DTR-7DTR-6 REMOTE CONTROL SpecificationsREMOTE CONTROL DTR-7Control positions and names Front panelDisplay Remote controller Control positions and names1 2 3 4 5 6 7 8 9 22 21 20 19ONKYO U.S.A. CORPORATION Williams Drive, Ramesy, N.J. 07446, U.S.AD9907-1