Integra DTR-7 Playing a digital source Digital Input Setup, Setting the Speaker level

Page 23

Playing a digital source (Digital Input Setup)

Setting the Speaker level

3

* Bass Peak Setup *

Bass Peak Level

Limiter = Yes

Peak Level =+18dB

Starting

The Test Tone

4

* Bass Peak Setup *

1.Turn Volume Up.

2.When Sound Distorts.

3.Press ENTER.

Level -31dB

•Using the on-screen display

1.Press the OSD MENU button.

2.Select “Speaker Setup” and then press the right edge of the ENTER/Cursor button.

3.Select “Bass Peak Setup” and then press the right edge of the ENTER/Cursor button.

The “Bass Peak Setup” screen appears.

Bass Peak Level Limiter :

Enables (Yes) / Disables (No) the bass peak limiter.

The Peak Level indicates the bass peak level when the limiter is set to Yes.

4.Select “Starting The Test Tone” and then press the right edge of the ENTER/Cursor button.

This generates a test signal and automatically sets the unit's MASTER VOLUME control knob to -27 dB.

You can now press the right and left edges of the ENTER/Cur- sor button to adjust the peak level in units of 1 dB.

5.Press the ENTER/Cursor button just before the sound is dis- torted.

The bass peak level is stored and the Speaker Setup screen is displayed again.

Playing a digital source (Digital Input Setup)

2

DIGITAL/
ANALOG		SPEAKERS			STEREO
ANALOG		A		PCM DIGITAL	DIRECT

3

PRESET/MODE ADJ

PUSH TO ENTER

PRESET/MODE ADJ

PUSH TO ENTER

Digital input setup

Each of the DVD, CD, VIDEO 1-3, and TAPE input channels can be set so that it accepts analog or digital audio input. The default setting is below. Change the setting according to the connection.

DVD: OPT2

VIDEO1: COAX1

VIDEO2: – – – –

VIDEO3: COAX2

TAPE: – – – –

CD: OPT1

Assume that you have connected a DVD player to the COAXIAL 1 connector.

1.Press the DVD input selector button.

2.Press the DIGITAL/ANALOG button until "Digital In- put?" appears.

3.Press the SMART SCAN CONTROLLER. The digital input setup mode has been set.

By rotating the SMART SCAN CONTROLLER, select the digi- tal audio input connector “COAX 1,” from among “OPT 1,” “OPT 2,” “ COAX 1,” “COAX 2” and “– – – – .” Selecting “– – – –”sets analog audio input.

4.Press the SMART SCAN CONTROLLER. This completes the digital input setup.

To select an input source using the on-screen display, follow steps 1 through 3 described on page 29.

23

Image 23

Contents Appendix Before usingPreparation OperationAVIS Important SafeguardsNote to CATV system installer Precautions1. Warranty Claim 5.PowerAluminum volume control FeaturesSupplied accessories Key FeaturesUsing the remote controller Before operating this unitInstalling the remote controller batteries have been made Audio equipment connectionsDo not plug in the power cord until all connectionsAC outlet connection Audio equipment connectionsConnections for remote control z Video equipment connections Decoder with 5.1-channeloutput Video equipment connectionsConnecting equipment with 5.1-channeloutput Speaker placement Connecting speakersCENTER SPEAKER Connecting speakersFRONT SPEAKERS SURROUND SPEAKERSConnecting power amplifiers Connecting power amplifiersConnecting speakers Connecting a subwooferConnecting the power Connecting an equalizer DTR-7Connecting the power Connecting a power cableAssembling the AM loop antenna Making antenna connectionsConnecting the antenna cable Directional IinkageConnecting an AM outdoor antenna Making antenna connectionsConnecting the included antennas Connecting an FM outdoor antennaScreen Setup Using the on-screendisplayHow to use the on-screendisplay OSD screens Using the on-screendisplaySetting the speaker configuration parameters Setting the speaker configurationFront Center SurroundUsing the on-screendisplay Setting the speaker configurationLoudspeaker Position Time Synchronization Setting the speaker distanceUsing the on-screendisplay R-Sur Setting the speaker LevelCenter RightBass Peak Level Manager* DTR-7only Setting the Speaker levelSetting the bass peak level Digital input setup Playing a digital source Digital Input SetupSetting the Speaker level Using the on-screendisplayTuning in a radio station Presetting FM/AM radio stationsProgramming radio stations Presetting FM/AM radio stationsCancelling preset stations 3. Start playing the selected input source Selecting an input sourceSelecting an input source Selecting an input source COAXIAL Digital Input SetupUsing the on-screendisplay Selecting an input sourceChanging the display Selecting an input sourceSelecting the speaker system Selecting an input source Adjusting the tone Bass and treble adjustmentUsing the on-screendisplay Selecting a preset stationUsing the on-screendisplay Playing a multichannel input sourceSetting the MULTI CHANNEL INPUT Listening Modes Using the Listening ModesBefore Using Listening Mode DSP Digital Signal Processor2. Listening mode button Using the listening modes3. MASTER VOLUME control knob 3. VOLUME buttonsUsing the listening modes Using the listening modesInput sources and listening modes Using the listening modesUsing the on-screendisplay Setting the listening mode parametersHow to set the listening mode parameters Late Night Setting the listening mode parametersListening mode parameters Re-EQCinema Re-EqualizationPHONO Video Assign SetupVideo Assign Setup Using the on-screendisplayTo erase a name Giving a name to each preset radio stationGiving a name to each input source To change a name3.Repeat the operation described in step Fine-tuningthe output level of each speakerTo use the above setting from now on 1.Press the CH LEVEL buttonUsing the on-screendisplay Other setup operationsVolume display method setup IntelliVolume setupRecording a source Recording a source while listening to music or amovie Recording from on audio /video sourceAdding sound to a video tape Recording a sourceUsing the on-screendisplay Enjoying Music and Movies in the Sub-room Using Multi-RoomRemote SystemOutline of Multi-roomRemote System To control the system in the sub-room Enjoying Music and Movies in the Sub-roomWhen the system is mounted in a rack Distance Setup The initial settingsInitial settings Config Setupindicator Using the remote controllerUsing the RC-392Mto control each device Turning the power on and off to the receiverControlling an Onkyo/Integra DVD player Using the remote controllerControlling an Onkyo/Integra CD player MODE SAT, CABLE, VCR, and TV buttons Using the remote controllerControlling an Onkyo/Integra MD recorder Controlling an Onkyo/Integra tape deckProgramming procedure Erasing a learned code from a MODE button Erasing a learned codeProgramming Macro mode Using a Macro function2 1 What is a Macro function?Macro Direct Learning function Using a Macro functionUsing a Macro function 3.Press the ENT button Using a Macro function1.Open the battery cover and remove the batteries Remedy Troubleshooting guideTrouble CauseOthers Troubleshooting guideFM/AM Video & audioDTR-6 SpecificationsDTR-7 DTR-7 SpecificationsREMOTE CONTROL REMOTE CONTROLDisplay Control positions and namesFront panel 22 21 20 19 Control positions and namesRemote controller 1 2 3 4 5 6 7 8 9D9907-1 ONKYO U.S.A. CORPORATIONWilliams Drive, Ramesy, N.J. 07446, U.S.A