Integra DTR-7 Using the remote controller, Using the RC-392Mto control each device, Send/Learn

Page 49

Using the remote controller

Using the remote controller

Overview

When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press the operation buttons. For example, if you wish to control the receiver from a remote controller, first press the MODE AUDIO button, then press an appropriate operation button. To control a CD player, press the MODE CD button, then press an appropriate operation button.

First, press the desired MODE button to make sure that the receiver is set to a correct mode.

Using the RC-392M to control each device

SEND/LEARN
indicator
POWER ON	POWER
	STNBY

MODE AUDIO

Turning the power on and off to the receiver

Note:

Before operating the RC-392M, turn on the POWER switch on the the receiver so that the unit enters standby mode.

1.Press the MODE AUDIO button.

2.Press the POWER ON button.

Pressing the POWER STNBY button will activate the power standby mode.

SEND/LEARN indicator

This indicator acts as a guide when commands are programmed into or sent by the remote controller. It also warns the user when an error is made or battery power is low.

POWER ON/STNBY

SLEEP LIGHT

MODE

AUDIO

DISPLAY
CH +/–	VOL
	TEST
	MUTING

INPUT

SELECTOR

Listening mode

SP A/B	LEVEL +/–
DIMMER	CH SEL

Controlling the receiver

1.Press the MODE AUDIO button.

2.Press the desired operation button.

Shaded buttons in the figure are the operation buttons used to control the receiver.

SLEEP : Sleep function

POWER ON/STNBY

:Power on/standby

DISPLAY : Changing the display

VOL Δ/∇ : Adjusting the volume

CH +/- : Tuner preset number increment/decrement

INPUT SELECTOR Listening mode

:Changing Listening mode

SP A/SP B	: Switching between Speakers A and B
CH SEL	: Selecting a speaker
DIMMER	: Adjusting the brightness of the display
LEVEL +/-	: Adjusting the speaker levels
TEST	: Test tone
MUTING	: Muting
LIGHT	: Illuminating the buttons.

49

Image 49

Contents Preparation Before usingOperation AppendixAVIS Important Safeguards1. Warranty Claim Precautions5.Power Note to CATV system installerSupplied accessories FeaturesKey Features Aluminum volume controlInstalling the remote controller batteries Before operating this unitUsing the remote controller Do not plug in the power Audio equipment connectionscord until all connections have been madeConnections for remote control z Audio equipment connectionsAC outlet connection Video equipment connections Connecting equipment with 5.1-channeloutput Video equipment connectionsDecoder with 5.1-channeloutput Speaker placement Connecting speakersFRONT SPEAKERS Connecting speakersSURROUND SPEAKERS CENTER SPEAKERConnecting speakers Connecting power amplifiersConnecting a subwoofer Connecting power amplifiersConnecting the power Connecting an equalizer DTR-7Connecting a power cable Connecting the powerConnecting the antenna cable Making antenna connectionsDirectional Iinkage Assembling the AM loop antennaConnecting the included antennas Making antenna connectionsConnecting an FM outdoor antenna Connecting an AM outdoor antennaHow to use the on-screendisplay Using the on-screendisplayScreen Setup OSD screens Using the on-screendisplayFront Setting the speaker configurationCenter Surround Setting the speaker configuration parametersUsing the on-screendisplay Setting the speaker configurationUsing the on-screendisplay Setting the speaker distanceLoudspeaker Position Time Synchronization Center Setting the speaker LevelRight R-SurSetting the bass peak level Setting the Speaker levelBass Peak Level Manager* DTR-7only Setting the Speaker level Playing a digital source Digital Input SetupUsing the on-screendisplay Digital input setupTuning in a radio station Presetting FM/AM radio stationsCancelling preset stations Presetting FM/AM radio stationsProgramming radio stations 3. Start playing the selected input source Selecting an input sourceSelecting an input source Selecting an input source Using the on-screendisplay Digital Input SetupSelecting an input source COAXIALSelecting the speaker system Selecting an input sourceChanging the display Selecting an input source Adjusting the tone Bass and treble adjustmentUsing the on-screendisplay Selecting a preset stationSetting the MULTI CHANNEL INPUT Playing a multichannel input sourceUsing the on-screendisplay Before Using Listening Mode Using the Listening ModesDSP Digital Signal Processor Listening Modes3. MASTER VOLUME control knob Using the listening modes3. VOLUME buttons 2. Listening mode buttonUsing the listening modes Using the listening modesInput sources and listening modes Using the listening modesHow to set the listening mode parameters Setting the listening mode parametersUsing the on-screendisplay Listening mode parameters Setting the listening mode parametersRe-EQCinema Re-Equalization Late NightVideo Assign Setup Video Assign SetupUsing the on-screendisplay PHONOGiving a name to each input source Giving a name to each preset radio stationTo change a name To erase a nameTo use the above setting from now on Fine-tuningthe output level of each speaker1.Press the CH LEVEL button 3.Repeat the operation described in stepVolume display method setup Other setup operationsIntelliVolume setup Using the on-screendisplaymovie Recording a source while listening to music or aRecording from on audio /video source Recording a sourceUsing the on-screendisplay Recording a sourceAdding sound to a video tape Outline of Multi-roomRemote System Using Multi-RoomRemote SystemEnjoying Music and Movies in the Sub-room When the system is mounted in a rack Enjoying Music and Movies in the Sub-roomTo control the system in the sub-room Initial settings The initial settingsConfig Setup Distance SetupUsing the RC-392Mto control each device Using the remote controllerTurning the power on and off to the receiver indicatorControlling an Onkyo/Integra CD player Using the remote controllerControlling an Onkyo/Integra DVD player Controlling an Onkyo/Integra MD recorder Using the remote controllerControlling an Onkyo/Integra tape deck MODE SAT, CABLE, VCR, and TV buttonsProgramming procedure Erasing a learned code from a MODE button Erasing a learned code2 1 Using a Macro functionWhat is a Macro function? Programming Macro modeMacro Direct Learning function Using a Macro functionUsing a Macro function 1.Open the battery cover and remove the batteries Using a Macro function3.Press the ENT button Trouble Troubleshooting guideCause RemedyFM/AM Troubleshooting guideVideo & audio OthersDTR-7 SpecificationsDTR-6 REMOTE CONTROL SpecificationsREMOTE CONTROL DTR-7Front panel Control positions and namesDisplay Remote controller Control positions and names1 2 3 4 5 6 7 8 9 22 21 20 19Williams Drive, Ramesy, N.J. 07446, U.S.A ONKYO U.S.A. CORPORATIOND9907-1