Integra DTR-7 instruction manual Using a Macro function

Page 56

1, 2 1

Using a Macro function

1, 2 1

1, 2 1

Erasing a learned remote controller button operation from the MACRO MODE buttons

1.Press and hold down the corresponding MODE button and press the MACRO MODE button, then release the buttons. When you press the MODE button, the SEND/LEARN indica- tor lights up. When you press the MACRO MODE button, the indicator turns off. When you release the buttons, the indicator flashes once.

2.Press the MACRO MODE button again.

The SEND/LEARN indicator flashes twice slowly. The learned operation is erased.

Erasing a learned remote controller button operation from the MACRO DIRECT button

1.Press and hold down any one of the MODE buttons and press the MACRO DIRECT button. Then release the but- tons.

When you press the MODE button, the SEND/LEARN indica- tor lights up. When you press the MACRO DIRECT button, the indicator turns off. When you release the buttons, the indicator flashes once.

2.Press the MACRO DIRECT button again.

The SEND/LEARN indicator flashes twice slowly. The learned

operation is erased.

Notes:

•If you do not press any button for more than 30 seconds, the SEND/ LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. Resume from Step 1.

•If you press a wrong button in Step 2, you may have overwritten the memory of the button you pressed.

56

Image 56

Contents Before using PreparationOperation AppendixImportant Safeguards AVISPrecautions 1. Warranty Claim5.Power Note to CATV system installerFeatures Supplied accessoriesKey Features Aluminum volume controlUsing the remote controller Before operating this unitInstalling the remote controller batteries Audio equipment connections Do not plug in the powercord until all connections have been madeAC outlet connection Audio equipment connectionsConnections for remote control z Video equipment connections Decoder with 5.1-channeloutput Video equipment connectionsConnecting equipment with 5.1-channeloutput Connecting speakers Speaker placementConnecting speakers FRONT SPEAKERSSURROUND SPEAKERS CENTER SPEAKERConnecting power amplifiers Connecting speakersConnecting a subwoofer Connecting power amplifiersConnecting an equalizer DTR-7 Connecting the powerConnecting a power cable Connecting the powerMaking antenna connections Connecting the antenna cableDirectional Iinkage Assembling the AM loop antennaMaking antenna connections Connecting the included antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaScreen Setup Using the on-screendisplayHow to use the on-screendisplay Using the on-screendisplay OSD screensSetting the speaker configuration FrontCenter Surround Setting the speaker configuration parametersSetting the speaker configuration Using the on-screendisplayLoudspeaker Position Time Synchronization Setting the speaker distanceUsing the on-screendisplay Setting the speaker Level CenterRight R-SurBass Peak Level Manager* DTR-7only Setting the Speaker levelSetting the bass peak level Playing a digital source Digital Input Setup Setting the Speaker levelUsing the on-screendisplay Digital input setupPresetting FM/AM radio stations Tuning in a radio stationProgramming radio stations Presetting FM/AM radio stationsCancelling preset stations Selecting an input source 3. Start playing the selected input sourceSelecting an input source Selecting an input source Digital Input Setup Using the on-screendisplaySelecting an input source COAXIALChanging the display Selecting an input sourceSelecting the speaker system Adjusting the tone Bass and treble adjustment Selecting an input sourceSelecting a preset station Using the on-screendisplayUsing the on-screendisplay Playing a multichannel input sourceSetting the MULTI CHANNEL INPUT Using the Listening Modes Before Using Listening ModeDSP Digital Signal Processor Listening ModesUsing the listening modes 3. MASTER VOLUME control knob3. VOLUME buttons 2. Listening mode buttonUsing the listening modes Using the listening modesUsing the listening modes Input sources and listening modesUsing the on-screendisplay Setting the listening mode parametersHow to set the listening mode parameters Setting the listening mode parameters Listening mode parametersRe-EQCinema Re-Equalization Late NightVideo Assign Setup Video Assign SetupUsing the on-screendisplay PHONOGiving a name to each preset radio station Giving a name to each input sourceTo change a name To erase a nameFine-tuningthe output level of each speaker To use the above setting from now on1.Press the CH LEVEL button 3.Repeat the operation described in stepOther setup operations Volume display method setupIntelliVolume setup Using the on-screendisplayRecording a source while listening to music or a movieRecording from on audio /video source Recording a sourceAdding sound to a video tape Recording a sourceUsing the on-screendisplay Enjoying Music and Movies in the Sub-room Using Multi-RoomRemote SystemOutline of Multi-roomRemote System To control the system in the sub-room Enjoying Music and Movies in the Sub-roomWhen the system is mounted in a rack The initial settings Initial settingsConfig Setup Distance SetupUsing the remote controller Using the RC-392Mto control each deviceTurning the power on and off to the receiver indicatorControlling an Onkyo/Integra DVD player Using the remote controllerControlling an Onkyo/Integra CD player Using the remote controller Controlling an Onkyo/Integra MD recorderControlling an Onkyo/Integra tape deck MODE SAT, CABLE, VCR, and TV buttonsProgramming procedure Erasing a learned code Erasing a learned code from a MODE buttonUsing a Macro function 2 1What is a Macro function? Programming Macro modeUsing a Macro function Macro Direct Learning functionUsing a Macro function 3.Press the ENT button Using a Macro function1.Open the battery cover and remove the batteries Troubleshooting guide TroubleCause RemedyTroubleshooting guide FM/AMVideo & audio OthersDTR-6 SpecificationsDTR-7 Specifications REMOTE CONTROLREMOTE CONTROL DTR-7Display Control positions and namesFront panel Control positions and names Remote controller1 2 3 4 5 6 7 8 9 22 21 20 19D9907-1 ONKYO U.S.A. CORPORATIONWilliams Drive, Ramesy, N.J. 07446, U.S.A