Integra DTR-7 instruction manual Setting the speaker Level, Center, Right, R-Sur, L-Sur SW

Page 21
Setting the speaker Level

Setting the speaker Level

1 SP/SYS SETUP

PRESET/MODE ADJ

PUSH TO ENTER

SPEAKERS

A

DSP

Using the test tone to adjust the speaker output levels

1.

Press the SP/SYS SETUP button repeatedly until

 

“Level Setup?” appears.

 

Press the SMART SCAN CONTROLLER.

 

The display shows “Left.”

2.

Rotate clockwise or counterclockwise the SMART SCAN

 

CONTROLLER to adjust the speaker output level.

 

You can adjust the output level of each speaker in the range of

 

12 to +12 dB, except for the subwoofer whose adjustment range

 

is -30 to +10 dB.

2

PRESET/MODE ADJ

SPEAKERS

 

STEREO

 

 

 

 

A

 

 

PCM DIGITAL

PUSH TO ENTER

Center

PRESET/MODE ADJ

Right

PUSH TO ENTER

R-Sur

L-Sur

SW

db

Press the SMART SCAN CONTROLLER.

You hear a test tone (pink noise) from the left front speaker.

Each time you press the SMART SCAN CONTROLLER, the

speaker that produces a test tone changes as below. Set the out-

put level of each speaker by rotating the SMART SCAN CON-

TROLLER so that you can hear the same level of test tone at the

listening position.

 

Left (Left front) Center (Center)

Right (Right front) R-Sur (Right

surround) L-Sur(Left surround)

Subwoofer (Subwoofer) Left

Notes:

•In order to correctly set the output levels, use a hand-held Sound Pressure Level meter (SPL), set to C-Weighting and Slow aver- aging. A Radio Shack® SPL meter (catalogue number 330- 2055) or equivalent can be used. Using the internal channel noise generators, set each channel so that you read 75 dB SPL from each channel.

•SPEAKER B, when selected, will be deselected automatically as soon as the test tone starts sounding. The Test Tone function is not available when the headphones are connected or when MULTI CH INPUT is selected.

•The test tone will not be output from the speaker that has been set to "No" in the configuration setup explained on the page 18,19.

•If the speaker level is set to +1dB or higher , the maximum level indicated on the display will change if you raise the volume level.

* Level Setup *

Left

= +1dB

Center

=

0dB

(Right

=

0dB)

1

2

3

4

 

 

 

•Using the on-screen display

1.Press the OSD MENU button.

2.Select “Speaker Setup” and then press the right edge of the ENTER/Cursor button.

3.Select “Level Setup” and then press the right edge of the ENTER/Cursor button.

The Level Setup screen appears and a test tone (pink noise) is output from the left front speaker. You can change the speaker that outputs the test tone in the following sequence.(When the cursor is on “Center,” you can press the lower edge of the EN- TER/Cursor button to display additional items.)

Left (Left front)Center Center (Center)Right Right (Right front)R-Sur R-Sur (Right surround) L-Sur L-Sur (Left surround) •Using Test button on the remote controller Subwoofer (Subwoofer) Manual background Left.

4.Set the output level of each speaker so that you can hear the same level of test tone in the listening position.

You can adjust the output level of each speaker in the range of - 12 to +12 dB, except for the subwoofer whose adjustment range is -30 to +10 dB.

5.Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode.

•Using Test button on the remote controller

1.Press the MODE AUDIO button.

2.Press the TEST button.

Left front speaker produces the test tone (pink noise).

3.To adjust the level of each speaker,press the CH SEL, but- ton to select a speaker and press the LEVEL +/- buttons to raise or lower the level.

4.Press rhe TEST button to complete adjustment.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Preparation Before usingOperation AppendixAVIS Important Safeguards1. Warranty Claim Precautions5.Power Note to CATV system installerSupplied accessories FeaturesKey Features Aluminum volume controlBefore operating this unit Installing the remote controller batteriesUsing the remote controller Do not plug in the power Audio equipment connectionscord until all connections have been madeAudio equipment connections Connections for remote control zAC outlet connection Video equipment connections Video equipment connections Connecting equipment with 5.1-channeloutputDecoder with 5.1-channeloutput Speaker placement Connecting speakersFRONT SPEAKERS Connecting speakersSURROUND SPEAKERS CENTER SPEAKERConnecting speakers Connecting power amplifiersConnecting a subwoofer Connecting power amplifiersConnecting the power Connecting an equalizer DTR-7Connecting a power cable Connecting the powerConnecting the antenna cable Making antenna connectionsDirectional Iinkage Assembling the AM loop antennaConnecting the included antennas Making antenna connectionsConnecting an FM outdoor antenna Connecting an AM outdoor antennaUsing the on-screendisplay How to use the on-screendisplayScreen Setup OSD screens Using the on-screendisplayFront Setting the speaker configurationCenter Surround Setting the speaker configuration parametersUsing the on-screendisplay Setting the speaker configurationSetting the speaker distance Using the on-screendisplayLoudspeaker Position Time Synchronization Center Setting the speaker LevelRight R-SurSetting the Speaker level Setting the bass peak levelBass Peak Level Manager* DTR-7only Setting the Speaker level Playing a digital source Digital Input SetupUsing the on-screendisplay Digital input setupTuning in a radio station Presetting FM/AM radio stationsPresetting FM/AM radio stations Cancelling preset stationsProgramming radio stations 3. Start playing the selected input source Selecting an input sourceSelecting an input source Selecting an input source Using the on-screendisplay Digital Input SetupSelecting an input source COAXIALSelecting an input source Selecting the speaker systemChanging the display Selecting an input source Adjusting the tone Bass and treble adjustmentUsing the on-screendisplay Selecting a preset stationPlaying a multichannel input source Setting the MULTI CHANNEL INPUTUsing the on-screendisplay Before Using Listening Mode Using the Listening ModesDSP Digital Signal Processor Listening Modes3. MASTER VOLUME control knob Using the listening modes3. VOLUME buttons 2. Listening mode buttonUsing the listening modes Using the listening modesInput sources and listening modes Using the listening modesSetting the listening mode parameters How to set the listening mode parametersUsing the on-screendisplay Listening mode parameters Setting the listening mode parametersRe-EQCinema Re-Equalization Late NightVideo Assign Setup Video Assign SetupUsing the on-screendisplay PHONOGiving a name to each input source Giving a name to each preset radio stationTo change a name To erase a nameTo use the above setting from now on Fine-tuningthe output level of each speaker1.Press the CH LEVEL button 3.Repeat the operation described in stepVolume display method setup Other setup operationsIntelliVolume setup Using the on-screendisplaymovie Recording a source while listening to music or aRecording from on audio /video source Recording a sourceRecording a source Using the on-screendisplayAdding sound to a video tape Using Multi-RoomRemote System Outline of Multi-roomRemote SystemEnjoying Music and Movies in the Sub-room Enjoying Music and Movies in the Sub-room When the system is mounted in a rackTo control the system in the sub-room Initial settings The initial settingsConfig Setup Distance SetupUsing the RC-392Mto control each device Using the remote controllerTurning the power on and off to the receiver indicatorUsing the remote controller Controlling an Onkyo/Integra CD playerControlling an Onkyo/Integra DVD player Controlling an Onkyo/Integra MD recorder Using the remote controllerControlling an Onkyo/Integra tape deck MODE SAT, CABLE, VCR, and TV buttonsProgramming procedure Erasing a learned code from a MODE button Erasing a learned code2 1 Using a Macro functionWhat is a Macro function? Programming Macro modeMacro Direct Learning function Using a Macro functionUsing a Macro function Using a Macro function 1.Open the battery cover and remove the batteries3.Press the ENT button Trouble Troubleshooting guideCause RemedyFM/AM Troubleshooting guideVideo & audio OthersSpecifications DTR-7DTR-6 REMOTE CONTROL SpecificationsREMOTE CONTROL DTR-7Control positions and names Front panelDisplay Remote controller Control positions and names1 2 3 4 5 6 7 8 9 22 21 20 19ONKYO U.S.A. CORPORATION Williams Drive, Ramesy, N.J. 07446, U.S.AD9907-1
Top Page Image Contents