Integra DTR-7 Making antenna connections, Directional Iinkage, Assembling the AM loop antenna

Page 14

Making antenna connections

Making antenna connections

	Outdoor	Indoor
	antenna	antenna
		300 ohms
		ribbon wire
1	2	3
		✦	✦	✦	✦
		✦	✦		✦
		✦✦		✦ ✦	✦
		✦✦			✦
			✦ ✦
				6	3	6
	Slit B		mm mm mm
	Slit B			15mm
				15mm
	Wire A
	Slit C

Connecting the antenna cable to the 75/300 ohm antenna adapter. (The antenna adapter must be separately ordered.)

Connecting the 300 ohm ribbon wire:

Loosen the screws and wrap the wire around these screws. Then tighten the screws with a screwdriver.

Connecting the coaxial cable:

1.With your fingernail or a small screwdriver, press the stoppers outward and remove the cover.

2.Remove the transformer wire A from slit B and insert it into slit C.

3.Prepare the coaxial cable as shown in the diagram.

Connect the 75/300 ohm antenna adapter to the coaxial cable. 1 Insert the end of the cable.

2 Clamp it in place with pliers.

4.Re-install the cover.

Directional linkage type splitter

To receiver

To TV (or VCR)

Directional Iinkage

Do not use the same antenna for both FM and TV (or VCR) recep- tion since the FM and TV (or VCR) signals can interfere with each other. If you must use a common FM/TV (or VCR) antenna, use a directional linkage type splitter.

Insert into the hole.

1	2	3

Assembling the AM loop antenna

Assemble the loop antenna as shown in the illustration.

•Refer to the next page for details on connecting the AM loop antenna.

Connecting the antenna cable

1.Press down the lever.

2.Insert the wire into the hole.

3.Release the lever to replace it.

14

Image 14

Contents Operation Before usingPreparation AppendixImportant Safeguards AVIS5.Power Precautions1. Warranty Claim Note to CATV system installerKey Features FeaturesSupplied accessories Aluminum volume controlUsing the remote controller Before operating this unitInstalling the remote controller batteries cord until all connections Audio equipment connectionsDo not plug in the power have been madeAC outlet connection Audio equipment connectionsConnections for remote control z Video equipment connections Decoder with 5.1-channeloutput Video equipment connectionsConnecting equipment with 5.1-channeloutput Connecting speakers Speaker placementSURROUND SPEAKERS Connecting speakersFRONT SPEAKERS CENTER SPEAKERConnecting a subwoofer Connecting power amplifiersConnecting speakers Connecting power amplifiersConnecting a power cable Connecting an equalizer DTR-7Connecting the power Connecting the powerDirectional Iinkage Making antenna connectionsConnecting the antenna cable Assembling the AM loop antennaConnecting an FM outdoor antenna Making antenna connectionsConnecting the included antennas Connecting an AM outdoor antennaScreen Setup Using the on-screendisplayHow to use the on-screendisplay Using the on-screendisplay OSD screensCenter Surround Setting the speaker configurationFront Setting the speaker configuration parametersSetting the speaker configuration Using the on-screendisplayLoudspeaker Position Time Synchronization Setting the speaker distanceUsing the on-screendisplay Right Setting the speaker LevelCenter R-SurBass Peak Level Manager* DTR-7only Setting the Speaker levelSetting the bass peak level Using the on-screendisplay Playing a digital source Digital Input SetupSetting the Speaker level Digital input setupPresetting FM/AM radio stations Tuning in a radio stationProgramming radio stations Presetting FM/AM radio stationsCancelling preset stations Selecting an input source 3. Start playing the selected input sourceSelecting an input source Selecting an input source Selecting an input source Digital Input SetupUsing the on-screendisplay COAXIALChanging the display Selecting an input sourceSelecting the speaker system Adjusting the tone Bass and treble adjustment Selecting an input sourceSelecting a preset station Using the on-screendisplayUsing the on-screendisplay Playing a multichannel input sourceSetting the MULTI CHANNEL INPUT DSP Digital Signal Processor Using the Listening ModesBefore Using Listening Mode Listening Modes3. VOLUME buttons Using the listening modes3. MASTER VOLUME control knob 2. Listening mode buttonUsing the listening modes Using the listening modesUsing the listening modes Input sources and listening modesUsing the on-screendisplay Setting the listening mode parametersHow to set the listening mode parameters Re-EQCinema Re-Equalization Setting the listening mode parametersListening mode parameters Late NightUsing the on-screendisplay Video Assign SetupVideo Assign Setup PHONOTo change a name Giving a name to each preset radio stationGiving a name to each input source To erase a name1.Press the CH LEVEL button Fine-tuningthe output level of each speakerTo use the above setting from now on 3.Repeat the operation described in stepIntelliVolume setup Other setup operationsVolume display method setup Using the on-screendisplayRecording from on audio /video source Recording a source while listening to music or amovie Recording a sourceAdding sound to a video tape Recording a sourceUsing the on-screendisplay Enjoying Music and Movies in the Sub-room Using Multi-RoomRemote SystemOutline of Multi-roomRemote System To control the system in the sub-room Enjoying Music and Movies in the Sub-roomWhen the system is mounted in a rack Config Setup The initial settingsInitial settings Distance SetupTurning the power on and off to the receiver Using the remote controllerUsing the RC-392Mto control each device indicatorControlling an Onkyo/Integra DVD player Using the remote controllerControlling an Onkyo/Integra CD player Controlling an Onkyo/Integra tape deck Using the remote controllerControlling an Onkyo/Integra MD recorder MODE SAT, CABLE, VCR, and TV buttonsProgramming procedure Erasing a learned code Erasing a learned code from a MODE buttonWhat is a Macro function? Using a Macro function2 1 Programming Macro modeUsing a Macro function Macro Direct Learning functionUsing a Macro function 3.Press the ENT button Using a Macro function1.Open the battery cover and remove the batteries Cause Troubleshooting guideTrouble RemedyVideo & audio Troubleshooting guideFM/AM OthersDTR-6 SpecificationsDTR-7 REMOTE CONTROL SpecificationsREMOTE CONTROL DTR-7Display Control positions and namesFront panel 1 2 3 4 5 6 7 8 9 Control positions and namesRemote controller 22 21 20 19D9907-1 ONKYO U.S.A. CORPORATIONWilliams Drive, Ramesy, N.J. 07446, U.S.A