Integra DTR-7 instruction manual Presetting FM/AM radio stations, Tuning in a radio station

Page 24

Presetting FM/AM radio stations

Presetting FM/AM radio stations

TUNING UP/DOWN

FM MUTE/MODE

CHARACTER/MEMORY

FM MUTE/

CHARACTER/

SP/SYS

AUDIO

BASS/

DIMMER

MODE

DOWN

TUNING

UP

MEMORY

SETUP

ADJUSTMENT

TREBLE

STANDBY/ON

MODE

W

N

D

O

PRESET/MODE ADJ

STANDBY MULTI SOURCE

SMART SCAN

CONTROLLER

POWER

PUSH TO ENTER

ON OFF

LISTENING MODE

REC OUT/

DIGITAL/

A SPEAKERS B

DISPLAY

DIRECT

STEREO

/DTS

THX

DSP

MULTI SOURCE ANALOG CH LEVEL

SURROUND

MODE

PHONES

MULTI CH INPUT

DVD VIDEO-1

VIDEO-2 VIDEO-3

VIDEO-4

TAPE

FM

AM

PHONO

C D

MASTER VOLUME

U

P

SMART SCAN

CONTROLLER

VIDEO4 (MONO)

S VIDEO

VIDEO

L AUDIO R

DTR-7 by

					FM/AM
1					Tuning in a radio station
1
					1. Press the FM or AM button.
					2. Use the TUNING UP/DOWN buttons to change the fre-
	FM	AM		A	A	quency.
				SPEAKERS	SPEAKERS
				FM		UP................the frequency increases.
						DOWN........ the frequency decreases.
					•	The frequency changes in 50 kHz steps in FM and 10 kHz in
						AM each time you press the TUNING UP/DOWN button.
					• In FM, if this button is held continuously for more than 0.5 sec-
						onds,the frequencies are scanned automatically (FM auto tuning
						mode).
2						When a broadcast is received, scanning stops.
2
DOWN	TUNING	UP	SPEAKERS	DSP	TUNED
			A		AUTO

FM MUTE/

MODE

DISPLAY

Listening to a stereo radio station (FM mode)

When you tune in a stereo FM station, the FM STEREO indicator lights up if the signal is sufficiently strong.

If the signal is weak, it may be impossible to tune in to the desired station. In this case, tune in as follows.

Press the FM MUTE/MODE button. The AUTO indicator

turns off. At this time, the station will be in mono and interstation noise will be heard. Select the station to which you want to listen.

DISPLAY button

Pressing the DISPLAY button each time will change the indication as follows:

Frequency (preset No.) Listening mode

24

Image 24

Contents Before using PreparationOperation AppendixImportant Safeguards AVISPrecautions 1. Warranty Claim5.Power Note to CATV system installerFeatures Supplied accessoriesKey Features Aluminum volume controlBefore operating this unit Installing the remote controller batteriesUsing the remote controller Audio equipment connections Do not plug in the powercord until all connections have been madeAudio equipment connections Connections for remote control zAC outlet connection Video equipment connections Video equipment connections Connecting equipment with 5.1-channeloutputDecoder with 5.1-channeloutput Connecting speakers Speaker placementConnecting speakers FRONT SPEAKERSSURROUND SPEAKERS CENTER SPEAKERConnecting power amplifiers Connecting speakersConnecting a subwoofer Connecting power amplifiersConnecting an equalizer DTR-7 Connecting the powerConnecting a power cable Connecting the powerMaking antenna connections Connecting the antenna cableDirectional Iinkage Assembling the AM loop antennaMaking antenna connections Connecting the included antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaUsing the on-screendisplay How to use the on-screendisplayScreen Setup Using the on-screendisplay OSD screensSetting the speaker configuration FrontCenter Surround Setting the speaker configuration parametersSetting the speaker configuration Using the on-screendisplaySetting the speaker distance Using the on-screendisplayLoudspeaker Position Time Synchronization Setting the speaker Level CenterRight R-SurSetting the Speaker level Setting the bass peak levelBass Peak Level Manager* DTR-7only Playing a digital source Digital Input Setup Setting the Speaker levelUsing the on-screendisplay Digital input setupPresetting FM/AM radio stations Tuning in a radio stationPresetting FM/AM radio stations Cancelling preset stationsProgramming radio stations Selecting an input source 3. Start playing the selected input sourceSelecting an input source Selecting an input source Digital Input Setup Using the on-screendisplaySelecting an input source COAXIALSelecting an input source Selecting the speaker systemChanging the display Adjusting the tone Bass and treble adjustment Selecting an input sourceSelecting a preset station Using the on-screendisplayPlaying a multichannel input source Setting the MULTI CHANNEL INPUTUsing the on-screendisplay Using the Listening Modes Before Using Listening ModeDSP Digital Signal Processor Listening ModesUsing the listening modes 3. MASTER VOLUME control knob3. VOLUME buttons 2. Listening mode buttonUsing the listening modes Using the listening modesUsing the listening modes Input sources and listening modesSetting the listening mode parameters How to set the listening mode parametersUsing the on-screendisplay Setting the listening mode parameters Listening mode parametersRe-EQCinema Re-Equalization Late NightVideo Assign Setup Video Assign SetupUsing the on-screendisplay PHONOGiving a name to each preset radio station Giving a name to each input sourceTo change a name To erase a nameFine-tuningthe output level of each speaker To use the above setting from now on1.Press the CH LEVEL button 3.Repeat the operation described in stepOther setup operations Volume display method setupIntelliVolume setup Using the on-screendisplayRecording a source while listening to music or a movieRecording from on audio /video source Recording a sourceRecording a source Using the on-screendisplayAdding sound to a video tape Using Multi-RoomRemote System Outline of Multi-roomRemote SystemEnjoying Music and Movies in the Sub-room Enjoying Music and Movies in the Sub-room When the system is mounted in a rackTo control the system in the sub-room The initial settings Initial settingsConfig Setup Distance SetupUsing the remote controller Using the RC-392Mto control each deviceTurning the power on and off to the receiver indicatorUsing the remote controller Controlling an Onkyo/Integra CD playerControlling an Onkyo/Integra DVD player Using the remote controller Controlling an Onkyo/Integra MD recorderControlling an Onkyo/Integra tape deck MODE SAT, CABLE, VCR, and TV buttonsProgramming procedure Erasing a learned code Erasing a learned code from a MODE buttonUsing a Macro function 2 1What is a Macro function? Programming Macro modeUsing a Macro function Macro Direct Learning functionUsing a Macro function Using a Macro function 1.Open the battery cover and remove the batteries3.Press the ENT button Troubleshooting guide TroubleCause RemedyTroubleshooting guide FM/AMVideo & audio OthersSpecifications DTR-7DTR-6 Specifications REMOTE CONTROLREMOTE CONTROL DTR-7Control positions and names Front panelDisplay Control positions and names Remote controller1 2 3 4 5 6 7 8 9 22 21 20 19ONKYO U.S.A. CORPORATION Williams Drive, Ramesy, N.J. 07446, U.S.AD9907-1