Windsor 10080480 operating instructions Operations, Special Notes Measure

Page 10

OPERATIONS

TECHNICAL SPECIFICATIONS

ITEM

Height

Length

Width

Width of scrub path

LENGTH

SPECIAL NOTES:

MEASURE

43inches (1092 mm) 40.5 inches (1029 mm)

22inches (559 mm)

16inches (406 mm)

HEIGHT

WIDTH

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with appliance.

The sound pressure level at the operator’s ear was measured to be 73.7 dBA. This was a nearfield, broad-band measurement taken in a typical industrial environment on a tile floor. This appliance contains no possible source of impact noise. The instantaneous sound pressure level is below 63 Pa.

The weighted root mean square acceleration at the operator’s arms was measured to be below 2.5m/s2 . This was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor. The measurement and related calculations were made in accordance with ISO 5349-1.

3-2	8630210 CLIPPER DUO 05/08/08

Image 10

Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Important Safety Instructions SafetyHazard Intensity Level Do not Operate MachineVolt Models Safety Label Location Technical Specifications OperationsOperations Special Notes MeasureHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS OPERATIONS-FILLING the Solution Tank Dry spills from top of solution tankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool MAINTENANCE-SERVICE Schedule Service ScheduleMAINTENANCE-COMPONENTS MAINTENANCE-PERIODIC Periodic MaintenanceMAINTENANCE-CIRCUIT Protection Circuit BreakersMAINTENANCE-SCRUB Deck Scrub Head MAINTENANCE-VACUUM Motor Vacuum Motor Carbon Brushes ReplacementMAINTENANCE-TROUBLESHOOTING Problem Cause SolutionParts List Brush Deck PRV no QTY Description Serial no From HOUSING, Brush DriveHOUSING, Brush Clip SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, DPDT3-POSITION Rocker BOOT, 3/8 Circuit BreakerSWITCH, Dpdt 2-POSITION Rocker SWITCH, Spst 2- Position RockerDecal PRV no QTY Description LABEL, AccessoryLABEL, Brush Install LABEL, Clipper DUOHand Tool NIPPLE, 1/8 FPT QD FEM Brass RETAINER, Solution HoseHand Tool HOSE, 1/4 RetractableHandle Handle Handle Bracket LEVER, Handle Release Left BRKT, Handle PivotPLATE, Handle Pivot Latch LEVER, Handle Release RightHandle Mounting CAP, HANDLE, Inner PANEL, CONN. AccessCAP, HANDLE, Outer BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank GASKET, Dome HOOK, WIREFORM, HandtoolDOME, 2 Hose Float SHUT-OFFSolution Solution 26 29 30 27 CLAMP, 1/4 ID Hose HARNESS, Handle ConnectorLABEL, Ground Symbol HOSE, 1/4 ID Nylobrd XSolution Tank Hose ASM, FCT Adptr X 60 Nbrd COVER, CLP SolutionNIPPLE, 1/8FPT QD ,MALE Brass CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum ASSY, VAC Motor SCR, #8 X 2 PphsmsCOVER, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle HUBCAP, 5/8 Shaft Wheel & AxleHUBCAP, 9.75 Wheel Axle ASM, Clipper DUOWiring Diagram HARNESS, Handle Wiring DiagramBrush Deck Wiring Harness HARNESS, Brush DeckSuggested Spare Parts Serial Numbers Model Serial #