Windsor 10080480 operating instructions Volt Models

Page 7

GROUNDING INSTRUCTIONS

THIS PRODUCT IS FOR COMMERCIAL USE ONLY.

ELECTRICAL:

In the USA this machine operates on a standard 15 amp 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.

EXTENSION CORDS:

If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

SAFETY

120 VOLT MODELS:

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in “Fig. A”. A temporary adaptor that looks like the adaptor in “Fig. C” may be used to connect this plug to a 2-pole receptacle as shown in “Fig. B”, if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.

Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

GROUNDED

OUTLET

GROUNDING PIN

(A)

GROUNDED OUTLET BOX

METAL SCREW

ADAPTER

TAB FOR

GROUNDING SCREW

(B)(C)

86302100 CLIPPER DUO 10/02/07

2-3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Safety Important Safety InstructionsDo not Operate Machine Hazard Intensity LevelVolt Models Safety Label Location Operations Technical SpecificationsSpecial Notes Measure OperationsHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS Dry spills from top of solution tank OPERATIONS-FILLING the Solution TankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool Service Schedule MAINTENANCE-SERVICE ScheduleMAINTENANCE-COMPONENTS Periodic Maintenance MAINTENANCE-PERIODICCircuit Breakers MAINTENANCE-CIRCUIT ProtectionMAINTENANCE-SCRUB Deck Scrub Head Vacuum Motor Carbon Brushes Replacement MAINTENANCE-VACUUM MotorProblem Cause Solution MAINTENANCE-TROUBLESHOOTINGParts List Brush Deck SCR, M4X8, SET, ISO4029,CP,BLK HOUSING, Brush DriveHOUSING, Brush Clip PRV no QTY Description Serial no FromBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, Spst 2- Position Rocker BOOT, 3/8 Circuit BreakerSWITCH, Dpdt 2-POSITION Rocker SWITCH, DPDT3-POSITION RockerDecal LABEL, Clipper DUO LABEL, AccessoryLABEL, Brush Install PRV no QTY DescriptionHand Tool HOSE, 1/4 Retractable RETAINER, Solution HoseHand Tool NIPPLE, 1/8 FPT QD FEM BrassHandle Handle Handle Bracket LEVER, Handle Release Right BRKT, Handle PivotPLATE, Handle Pivot Latch LEVER, Handle Release LeftHandle Mounting BRUSH, Handle CAP PANEL, CONN. AccessCAP, HANDLE, Outer CAP, HANDLE, InnerHandle Release Lever Handle Release Lever Recovery Tank Float SHUT-OFF HOOK, WIREFORM, HandtoolDOME, 2 Hose GASKET, DomeSolution Solution 26 29 30 27 HOSE, 1/4 ID Nylobrd X HARNESS, Handle ConnectorLABEL, Ground Symbol CLAMP, 1/4 ID HoseSolution Tank CLAMP, 1.0 Worm Gear COVER, CLP SolutionNIPPLE, 1/8FPT QD ,MALE Brass Hose ASM, FCT Adptr X 60 NbrdVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum CLAMP, 1.75 Worm Gear SCR, #8 X 2 PphsmsCOVER, VAC Motor ASSY, VAC MotorWheel & Axle Axle ASM, Clipper DUO Wheel & AxleHUBCAP, 9.75 Wheel HUBCAP, 5/8 ShaftWiring Diagram HARNESS, Brush Deck Wiring DiagramBrush Deck Wiring Harness HARNESS, HandleSuggested Spare Parts Model Serial # Serial Numbers
Top Page Image Contents