Windsor 10080480 operating instructions Important Safety Instructions

Page 5

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

This machine is for commercial use.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet. See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.

Use only indoors. Do not use outdoors or expose to rain.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near children. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run machine over cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is intended for cleaning carpet only.

Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. This machine is not suitable for picking up health endangering dust.

Turn off all controls before unplugging.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

SAVE THESE INSTRUCTIONS

86302100 CLIPPER DUO 10/02/07

2-1

Image 5
Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Safety Important Safety InstructionsDo not Operate Machine Hazard Intensity LevelVolt Models Safety Label Location Operations Technical SpecificationsSpecial Notes Measure OperationsHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS Dry spills from top of solution tank OPERATIONS-FILLING the Solution TankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool Service Schedule MAINTENANCE-SERVICE ScheduleMAINTENANCE-COMPONENTS Periodic Maintenance MAINTENANCE-PERIODICCircuit Breakers MAINTENANCE-CIRCUIT ProtectionMAINTENANCE-SCRUB Deck Scrub Head Vacuum Motor Carbon Brushes Replacement MAINTENANCE-VACUUM MotorProblem Cause Solution MAINTENANCE-TROUBLESHOOTINGParts List Brush Deck HOUSING, Brush Clip HOUSING, Brush DrivePRV no QTY Description Serial no From SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, Dpdt 2-POSITION Rocker BOOT, 3/8 Circuit BreakerSWITCH, DPDT3-POSITION Rocker SWITCH, Spst 2- Position RockerDecal LABEL, Brush Install LABEL, AccessoryPRV no QTY Description LABEL, Clipper DUOHand Tool Hand Tool RETAINER, Solution HoseNIPPLE, 1/8 FPT QD FEM Brass HOSE, 1/4 RetractableHandle Handle Handle Bracket PLATE, Handle Pivot Latch BRKT, Handle PivotLEVER, Handle Release Left LEVER, Handle Release RightHandle Mounting CAP, HANDLE, Outer PANEL, CONN. AccessCAP, HANDLE, Inner BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank DOME, 2 Hose HOOK, WIREFORM, HandtoolGASKET, Dome Float SHUT-OFFSolution Solution 26 29 30 27 LABEL, Ground Symbol HARNESS, Handle ConnectorCLAMP, 1/4 ID Hose HOSE, 1/4 ID Nylobrd XSolution Tank NIPPLE, 1/8FPT QD ,MALE Brass COVER, CLP SolutionHose ASM, FCT Adptr X 60 Nbrd CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum COVER, VAC Motor SCR, #8 X 2 PphsmsASSY, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle HUBCAP, 9.75 Wheel Wheel & AxleHUBCAP, 5/8 Shaft Axle ASM, Clipper DUOWiring Diagram Brush Deck Wiring Harness Wiring DiagramHARNESS, Handle HARNESS, Brush DeckSuggested Spare Parts Model Serial # Serial Numbers