Windsor 10080480 operating instructions Hazard Intensity Level, Do not Operate Machine

Page 6

SAFETY

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNINGand CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts.

2-2

86302100 CLIPPER DUO 10/02/07

Image 6
Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Important Safety Instructions SafetyHazard Intensity Level Do not Operate MachineVolt Models Safety Label Location Technical Specifications OperationsOperations Special Notes MeasureHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS OPERATIONS-FILLING the Solution Tank Dry spills from top of solution tankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool MAINTENANCE-SERVICE Schedule Service ScheduleMAINTENANCE-COMPONENTS MAINTENANCE-PERIODIC Periodic MaintenanceMAINTENANCE-CIRCUIT Protection Circuit BreakersMAINTENANCE-SCRUB Deck Scrub Head MAINTENANCE-VACUUM Motor Vacuum Motor Carbon Brushes ReplacementMAINTENANCE-TROUBLESHOOTING Problem Cause SolutionParts List Brush Deck PRV no QTY Description Serial no From HOUSING, Brush DriveHOUSING, Brush Clip SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, DPDT3-POSITION Rocker BOOT, 3/8 Circuit BreakerSWITCH, Dpdt 2-POSITION Rocker SWITCH, Spst 2- Position RockerDecal PRV no QTY Description LABEL, AccessoryLABEL, Brush Install LABEL, Clipper DUOHand Tool NIPPLE, 1/8 FPT QD FEM Brass RETAINER, Solution HoseHand Tool HOSE, 1/4 RetractableHandle Handle Handle Bracket LEVER, Handle Release Left BRKT, Handle PivotPLATE, Handle Pivot Latch LEVER, Handle Release RightHandle Mounting CAP, HANDLE, Inner PANEL, CONN. AccessCAP, HANDLE, Outer BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank GASKET, Dome HOOK, WIREFORM, HandtoolDOME, 2 Hose Float SHUT-OFFSolution Solution 26 29 30 27 CLAMP, 1/4 ID Hose HARNESS, Handle ConnectorLABEL, Ground Symbol HOSE, 1/4 ID Nylobrd XSolution Tank Hose ASM, FCT Adptr X 60 Nbrd COVER, CLP SolutionNIPPLE, 1/8FPT QD ,MALE Brass CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum ASSY, VAC Motor SCR, #8 X 2 PphsmsCOVER, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle HUBCAP, 5/8 Shaft Wheel & AxleHUBCAP, 9.75 Wheel Axle ASM, Clipper DUOWiring Diagram HARNESS, Handle Wiring DiagramBrush Deck Wiring Harness HARNESS, Brush DeckSuggested Spare Parts Serial Numbers Model Serial #