Windsor 10080480 operating instructions Shut

Page 18

OPERATIONS-OPERATING THE MACHINE

ALTERNATE CLEANING PATH

Start at wall closest to power outlet. For large areas flip handle and operate machine in parallel passes, overlapping brush path. Clean perimeter last.

VACUUM INTAKE

SOLUTION INTAKE

STEP 5

		STEP 6
	CENTER	SHUT
	OFF	DOWN
	POSITION	DOWN
	POSITION

During operation, observe the following: This machine is equipped with clear dome to facilitate operator viewing of dirty solution and vacuum air flow.

During operation, observe the vacuum intake. Large amounts of water or foam entering the vacuum system can damage the vacuum motor. If you notice either condition, shut down the machine immediately. Empty recovery tank and/or add defoamer to recovery tank.

Use right side of machine for cleaning against walls.

After cleaning, turn off all controls, and carefully unplug machine.

3-10	86302100 CLIPPER DUO 10/02/07

Image 18

Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Important Safety Instructions SafetyHazard Intensity Level Do not Operate MachineVolt Models Safety Label Location Technical Specifications OperationsOperations Special Notes MeasureHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS OPERATIONS-FILLING the Solution Tank Dry spills from top of solution tankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool MAINTENANCE-SERVICE Schedule Service ScheduleMAINTENANCE-COMPONENTS MAINTENANCE-PERIODIC Periodic MaintenanceMAINTENANCE-CIRCUIT Protection Circuit BreakersMAINTENANCE-SCRUB Deck Scrub Head MAINTENANCE-VACUUM Motor Vacuum Motor Carbon Brushes ReplacementMAINTENANCE-TROUBLESHOOTING Problem Cause SolutionParts List Brush Deck PRV no QTY Description Serial no From HOUSING, Brush DriveHOUSING, Brush Clip SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, DPDT3-POSITION Rocker BOOT, 3/8 Circuit BreakerSWITCH, Dpdt 2-POSITION Rocker SWITCH, Spst 2- Position RockerDecal PRV no QTY Description LABEL, AccessoryLABEL, Brush Install LABEL, Clipper DUOHand Tool NIPPLE, 1/8 FPT QD FEM Brass RETAINER, Solution HoseHand Tool HOSE, 1/4 RetractableHandle Handle Handle Bracket LEVER, Handle Release Left BRKT, Handle PivotPLATE, Handle Pivot Latch LEVER, Handle Release RightHandle Mounting CAP, HANDLE, Inner PANEL, CONN. AccessCAP, HANDLE, Outer BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank GASKET, Dome HOOK, WIREFORM, HandtoolDOME, 2 Hose Float SHUT-OFFSolution Solution 26 29 30 27 CLAMP, 1/4 ID Hose HARNESS, Handle ConnectorLABEL, Ground Symbol HOSE, 1/4 ID Nylobrd XSolution Tank Hose ASM, FCT Adptr X 60 Nbrd COVER, CLP SolutionNIPPLE, 1/8FPT QD ,MALE Brass CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum ASSY, VAC Motor SCR, #8 X 2 PphsmsCOVER, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle HUBCAP, 5/8 Shaft Wheel & AxleHUBCAP, 9.75 Wheel Axle ASM, Clipper DUOWiring Diagram HARNESS, Handle Wiring DiagramBrush Deck Wiring Harness HARNESS, Brush DeckSuggested Spare Parts Serial Numbers Model Serial #