Windsor 10080480 PRV no QTY Description Serial no From, SCR, M4X8, SET, ISO4029,CP,BLK

Page 31

						BRUSH DECK

	REF	PART NO.	PRV NO.	QTY	DESCRIPTION	SERIAL NO.	NOTES:
	REF	PART NO.	PRV NO.	QTY	DESCRIPTION	FROM	NOTES:
						FROM
	1	86223780	70896	8	SCR, M4X8, SET, ISO4029,CP,BLK
	2	86224170	730410	2	SHAFT, 6.2MM BRUSH DRIVE
	3	86012800	-	2	SHAFT ASM, BRUSH END CAP
	4	86012810	-	1	SHAFT, ASM, DRIVE 16”
	5	86223520	67598	3	RING, 28MM INT SNAP
	5	86223520	67598	3	PHOSPHATE
					PHOSPHATE
	6	86223310	64116	1	PULLEY, 5MM HTD, 18T, 12.7 ID
	7	86215250	11049	1	BELT, 2S 5MM HTD, 15W, 128T
	8	86224660	730393	1	SPRING, TENSIONER
	9	86173330	87513	1	WASHER, M5 FLAT, ISO7093 SS
	10	86014990	-	9	SCR, M5X20, SHCS ISO4762, SS
	11	86215870	140914	1	BRKT, TENSIONER ARM
	12	86012780	-	2	PULLEY ASM, 5MM HTD 22T
	13A	86216050	12530	1	BRUSH, EXTRACTOR 16”
	13B	86295520	-	1	BRUSH, EXTRACTOR 16”
	13B	86295520	-	1	NATURAL
					NATURAL
	14	86223490	67468	2	RING, 10MM EXT SNAP, DIN 471
	15	86224130	730394	1	SHAFT, TENSIONER
	16	86219380	41546	1	HOUSING, BRUSH DRIVE
	17	86294070	-	1	PULLEY, 36T 5MM HTD
	18	86012790	-	2	SHAFT ASM, BRUSH DRIVE
	19	86172970	70911	3	SCR, M5X12, PHLP FHMS,
	19	86172970	70911	3	ISO7046, SS
					ISO7046, SS
	20	86222870	620103	1	PLATE, BRUSH DRIVE COVER
	21	86217780	32058	1	EXTRUSION, DUAL BRUSH 16”
	22	86219390	41548	1	HOUSING, BRUSH CLIP
	23	86173350	87515	4	WASHER, M5, FLAT, ISO7089,SS
	24	86172980	70912	2	SCR, KA50X10, PT OHS,
	24	86172980	70912	2	WN14112, PLTD
					WN14112, PLTD
	25	86224630	730380	2	SPRING, BRUSH CLIP
	26	86277130	70795	7	SCR, 5/16-18 X 1.00 CARRIAGE SS
	27	86215230	09161	1	BEARING, BRONZE FLANGED
	28	86294060	-	1	PULLEY, 30T 5MM HTD

86302100 CLIPPER DUO 10/02/07

5-2

Image 31

Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Safety Important Safety InstructionsDo not Operate Machine Hazard Intensity LevelVolt Models Safety Label Location Operations Technical SpecificationsSpecial Notes Measure OperationsHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS Dry spills from top of solution tank OPERATIONS-FILLING the Solution TankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool Service Schedule MAINTENANCE-SERVICE ScheduleMAINTENANCE-COMPONENTS Periodic Maintenance MAINTENANCE-PERIODICCircuit Breakers MAINTENANCE-CIRCUIT ProtectionMAINTENANCE-SCRUB Deck Scrub Head Vacuum Motor Carbon Brushes Replacement MAINTENANCE-VACUUM MotorProblem Cause Solution MAINTENANCE-TROUBLESHOOTINGParts List Brush Deck SCR, M4X8, SET, ISO4029,CP,BLK HOUSING, Brush DriveHOUSING, Brush Clip PRV no QTY Description Serial no FromBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, Spst 2- Position Rocker BOOT, 3/8 Circuit BreakerSWITCH, Dpdt 2-POSITION Rocker SWITCH, DPDT3-POSITION RockerDecal LABEL, Clipper DUO LABEL, AccessoryLABEL, Brush Install PRV no QTY DescriptionHand Tool HOSE, 1/4 Retractable RETAINER, Solution HoseHand Tool NIPPLE, 1/8 FPT QD FEM BrassHandle Handle Handle Bracket LEVER, Handle Release Right BRKT, Handle PivotPLATE, Handle Pivot Latch LEVER, Handle Release LeftHandle Mounting BRUSH, Handle CAP PANEL, CONN. AccessCAP, HANDLE, Outer CAP, HANDLE, InnerHandle Release Lever Handle Release Lever Recovery Tank Float SHUT-OFF HOOK, WIREFORM, HandtoolDOME, 2 Hose GASKET, DomeSolution Solution 26 29 30 27 HOSE, 1/4 ID Nylobrd X HARNESS, Handle ConnectorLABEL, Ground Symbol CLAMP, 1/4 ID HoseSolution Tank CLAMP, 1.0 Worm Gear COVER, CLP SolutionNIPPLE, 1/8FPT QD ,MALE Brass Hose ASM, FCT Adptr X 60 NbrdVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum CLAMP, 1.75 Worm Gear SCR, #8 X 2 PphsmsCOVER, VAC Motor ASSY, VAC MotorWheel & Axle Axle ASM, Clipper DUO Wheel & AxleHUBCAP, 9.75 Wheel HUBCAP, 5/8 ShaftWiring Diagram HARNESS, Brush Deck Wiring DiagramBrush Deck Wiring Harness HARNESS, HandleSuggested Spare Parts Model Serial # Serial Numbers