Windsor 10080480 OPERATIONS-FILLING the Solution Tank, Dry spills from top of solution tank

Page 14

	OPERATIONS-FILLING THE SOLUTION TANK
	Do not put defoamer, solvents, spotter or
	prespray chemicals in the solution tank.		REMOVE SOLUTION
	Do not allow water to spill into vacuum motor inlet.		FILL COVER
	Dry spills from top of solution tank.
	Use only the suitable chemicals listed below. Using
	incompatible chemicals will damage the machine.
	Damages of this type are not covered under warranty.
	Carefully read ingredients on manufacturer’s label before
	using any product in this machine.
	CHEMICALS
	Suitable Chemicals	Non-Compatible Chemicals	STEP 1
	Alkalis	Aldehydes	STEP 1
	Alkalis	Aldehydes
	Detergents	Aromatic Hydrocarbons	ADD WATER
	Hydroxides	SP Butyls	ADD WATER
	Hydroxides	SP Butyls	10 Gal.
	Soaps	Carbon Tetrachloride	10 Gal.
	Soaps	Carbon Tetrachloride	(38 Lt)
	Vinegar	Clorox*	(38 Lt)
	Vinegar	Clorox*
		Chlorinated Bleaches
		Chlorinated Hydrocarbons
		Lysol*	OR
		Methyl Ethel Ketone (MEK)	OR
		Perchorethylene (perc)
		Phenolics
		Trichlorethylene
		D-Limonene	STEP 2

FILL LINE

ADD CLEANING

CHEMICAL PER

CHEMICAL LABELING

STEP 3

REPLACE SOLUTION

FILL COVER

STEP 4

3-6	86302100 CLIPPER DUO 10/02/07

Image 14

Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Important Safety Instructions SafetyHazard Intensity Level Do not Operate MachineVolt Models Safety Label Location Technical Specifications OperationsOperations Special Notes MeasureHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS OPERATIONS-FILLING the Solution Tank Dry spills from top of solution tankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool MAINTENANCE-SERVICE Schedule Service ScheduleMAINTENANCE-COMPONENTS MAINTENANCE-PERIODIC Periodic MaintenanceMAINTENANCE-CIRCUIT Protection Circuit BreakersMAINTENANCE-SCRUB Deck Scrub Head MAINTENANCE-VACUUM Motor Vacuum Motor Carbon Brushes ReplacementMAINTENANCE-TROUBLESHOOTING Problem Cause SolutionParts List Brush Deck PRV no QTY Description Serial no From HOUSING, Brush DriveHOUSING, Brush Clip SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, DPDT3-POSITION Rocker BOOT, 3/8 Circuit BreakerSWITCH, Dpdt 2-POSITION Rocker SWITCH, Spst 2- Position RockerDecal PRV no QTY Description LABEL, AccessoryLABEL, Brush Install LABEL, Clipper DUOHand Tool NIPPLE, 1/8 FPT QD FEM Brass RETAINER, Solution HoseHand Tool HOSE, 1/4 RetractableHandle Handle Handle Bracket LEVER, Handle Release Left BRKT, Handle PivotPLATE, Handle Pivot Latch LEVER, Handle Release RightHandle Mounting CAP, HANDLE, Inner PANEL, CONN. AccessCAP, HANDLE, Outer BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank GASKET, Dome HOOK, WIREFORM, HandtoolDOME, 2 Hose Float SHUT-OFFSolution Solution 26 29 30 27 CLAMP, 1/4 ID Hose HARNESS, Handle ConnectorLABEL, Ground Symbol HOSE, 1/4 ID Nylobrd XSolution Tank Hose ASM, FCT Adptr X 60 Nbrd COVER, CLP SolutionNIPPLE, 1/8FPT QD ,MALE Brass CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum ASSY, VAC Motor SCR, #8 X 2 PphsmsCOVER, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle HUBCAP, 5/8 Shaft Wheel & AxleHUBCAP, 9.75 Wheel Axle ASM, Clipper DUOWiring Diagram HARNESS, Handle Wiring DiagramBrush Deck Wiring Harness HARNESS, Brush DeckSuggested Spare Parts Serial Numbers Model Serial #