Windsor 10080480 operating instructions OPERATIONS-OPERATING the Machine

Page 17

OPERATIONS-OPERATING THE MACHINE

1.This machine can be operated in either direction. For smaller areas operate the machine by pulling rearward.

2.For larger unobstructed areas, flip the handle and use the machine’s brush assisted propelling motion.

Start at wall closest to power outlet. For small areas, pull straight back without pushing down on handle.

Release intermittent trigger switches or turn off continuous setting on solution switch approximately 1 foot before ending cleaning pass.

2	1
	STEP 1

STEP 2

1 ft.

(30 cm)

STEP 3

Push down on handle to raise vacuum shoe and	1 in.
Push down on handle to raise vacuum shoe and	(25mm)
brush before moving to the next cleaning pass.
Overlap brush contact area approximately 1 inch.
		STEP 4
86302100 CLIPPER DUO 10/02/07		3-9

Image 17

Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Safety Important Safety InstructionsDo not Operate Machine Hazard Intensity LevelVolt Models Safety Label Location Operations Technical SpecificationsSpecial Notes Measure OperationsHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS Dry spills from top of solution tank OPERATIONS-FILLING the Solution TankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool Service Schedule MAINTENANCE-SERVICE ScheduleMAINTENANCE-COMPONENTS Periodic Maintenance MAINTENANCE-PERIODICCircuit Breakers MAINTENANCE-CIRCUIT ProtectionMAINTENANCE-SCRUB Deck Scrub Head Vacuum Motor Carbon Brushes Replacement MAINTENANCE-VACUUM MotorProblem Cause Solution MAINTENANCE-TROUBLESHOOTINGParts List Brush Deck HOUSING, Brush Clip HOUSING, Brush DrivePRV no QTY Description Serial no From SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel SWITCH, Dpdt 2-POSITION Rocker BOOT, 3/8 Circuit BreakerSWITCH, DPDT3-POSITION Rocker SWITCH, Spst 2- Position RockerDecal LABEL, Brush Install LABEL, AccessoryPRV no QTY Description LABEL, Clipper DUOHand Tool Hand Tool RETAINER, Solution HoseNIPPLE, 1/8 FPT QD FEM Brass HOSE, 1/4 RetractableHandle Handle Handle Bracket PLATE, Handle Pivot Latch BRKT, Handle PivotLEVER, Handle Release Left LEVER, Handle Release RightHandle Mounting CAP, HANDLE, Outer PANEL, CONN. AccessCAP, HANDLE, Inner BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank DOME, 2 Hose HOOK, WIREFORM, HandtoolGASKET, Dome Float SHUT-OFFSolution Solution 26 29 30 27 LABEL, Ground Symbol HARNESS, Handle ConnectorCLAMP, 1/4 ID Hose HOSE, 1/4 ID Nylobrd XSolution Tank NIPPLE, 1/8FPT QD ,MALE Brass COVER, CLP SolutionHose ASM, FCT Adptr X 60 Nbrd CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum COVER, VAC Motor SCR, #8 X 2 PphsmsASSY, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle HUBCAP, 9.75 Wheel Wheel & AxleHUBCAP, 5/8 Shaft Axle ASM, Clipper DUOWiring Diagram Brush Deck Wiring Harness Wiring DiagramHARNESS, Handle HARNESS, Brush DeckSuggested Spare Parts Model Serial # Serial Numbers