Windsor 10080480 operating instructions Maintenance-Troubleshooting, Problem Cause Solution

Page 28

MAINTENANCE-TROUBLESHOOTING

	PROBLEM	CAUSE	SOLUTION
	No Power, Nothing	Is the cord plugged in.	Plug in cord.
	No Power, Nothing	Circuit breaker tripped in building.	Reset breaker.
	Runs	Circuit breaker tripped in building.	Reset breaker.
	Runs	Faulty switch.	Call for service.
		Faulty switch.	Call for service.
		Faulty power cord or pigtail.	Call for service.
		Vacuum circuit breaker tripped.	Reset breaker.
	Vacuum Motor Will Not	Faulty main vacuum switch.	Call for service.
	Run	Loose wiring.	Call for service.
		Faulty vac motor.	Call for service.
		Debris lodged in vac shoe.	Remove debris from vac shoe.
	Vacuum Motor Runs	Dome gasket defective or missing.	Replace as necessary.
	But Suction Is Poor	Vacuum hose cracked or hose cuff loose.	Replace or repair as necessary.
		Recovery tank full / float ball stuck in the	Turn off vac motor. Drain and rinse
		up position.	recovery tank.
		Pump switch in intermittent position.	Turn to continuous or use buttons on
	Poor Or No Water Flow		handle
	(Carpet Is Streaky)	Jets clogged or missing.	Clean using a vinegar /water solution or
			replace.
		Solution filter clogged.	Drain solution tank and clean solution
			filter.
		Faulty solenoid.	Call for service.
	Brush Does Not Spin	Main switch off or in hand tool mode.	Turn main switch to machine mode.
	Brush Does Not Spin	Brush circuit breaker tripped.	Reset circuit breaker.
		Brush circuit breaker tripped.	Reset circuit breaker.
		Brush belt broken.	Replace as necessary.
		Faulty brush motor.	Call for service.

4-8	86302100 CLIPPER DUO 10/02/07

Image 28

Contents Carpet Extractor Machine Data LOG/OVERVIEW Table of Contents HOW to USE this Manual Important Safety Instructions SafetyHazard Intensity Level Do not Operate MachineVolt Models Safety Label Location Technical Specifications OperationsOperations Special Notes MeasureHOW this Machine Works OPERATIONS-COMPONENTS OPERATIONS-COMPONENTS OPERATIONS-FILLING the Solution Tank Dry spills from top of solution tankOPERATIONS-PRE RUN Setup OPERATIONS-PRE RUN Setup OPERATIONS-OPERATING the Machine Shut Recovery OPERATIONS-USING the Hand Tool MAINTENANCE-SERVICE Schedule Service ScheduleMAINTENANCE-COMPONENTS MAINTENANCE-PERIODIC Periodic MaintenanceMAINTENANCE-CIRCUIT Protection Circuit BreakersMAINTENANCE-SCRUB Deck Scrub Head MAINTENANCE-VACUUM Motor Vacuum Motor Carbon Brushes ReplacementMAINTENANCE-TROUBLESHOOTING Problem Cause SolutionParts List Brush Deck HOUSING, Brush Drive HOUSING, Brush ClipPRV no QTY Description Serial no From SCR, M4X8, SET, ISO4029,CP,BLKBrush Deck Motor Brush Deck Motor Brush Deck Mounting Brush Deck Mounting Control Panel BOOT, 3/8 Circuit Breaker SWITCH, Dpdt 2-POSITION RockerSWITCH, DPDT3-POSITION Rocker SWITCH, Spst 2- Position RockerDecal LABEL, Accessory LABEL, Brush InstallPRV no QTY Description LABEL, Clipper DUOHand Tool RETAINER, Solution Hose Hand ToolNIPPLE, 1/8 FPT QD FEM Brass HOSE, 1/4 RetractableHandle Handle Handle Bracket BRKT, Handle Pivot PLATE, Handle Pivot LatchLEVER, Handle Release Left LEVER, Handle Release RightHandle Mounting PANEL, CONN. Access CAP, HANDLE, OuterCAP, HANDLE, Inner BRUSH, Handle CAPHandle Release Lever Handle Release Lever Recovery Tank HOOK, WIREFORM, Handtool DOME, 2 HoseGASKET, Dome Float SHUT-OFFSolution Solution 26 29 30 27 HARNESS, Handle Connector LABEL, Ground SymbolCLAMP, 1/4 ID Hose HOSE, 1/4 ID Nylobrd XSolution Tank COVER, CLP Solution NIPPLE, 1/8FPT QD ,MALE BrassHose ASM, FCT Adptr X 60 Nbrd CLAMP, 1.0 Worm GearVAC Shoe VAC Shoe VAC Shoe Mounting VAC Shoe Mounting Vacuum SCR, #8 X 2 Pphsms COVER, VAC MotorASSY, VAC Motor CLAMP, 1.75 Worm GearWheel & Axle Wheel & Axle HUBCAP, 9.75 WheelHUBCAP, 5/8 Shaft Axle ASM, Clipper DUOWiring Diagram Wiring Diagram Brush Deck Wiring HarnessHARNESS, Handle HARNESS, Brush DeckSuggested Spare Parts Serial Numbers Model Serial #