Viking Access Systems Q7 manual Control Board References, EMI Board Connector

Page 6

CONTROL BOARD REFERENCES:

1.POWER HARNESS CONNECTOR provides power to the control board. pg 18-19

2.“OPEN LEFT” & “OPEN RIGHT” provides power to the motor. pg 20

3.LIMIT SETUP BUTTONS

sets limit positions. pg 20-21

4.FEATURE ACTIVATION TRIM POTS activate and set features. pg 24

5.“EPS1” CONNECTOR

monitors manual release operation.

6.“EPS2” CONNECTOR monitors the limit positions.

7.EMI BOARD CONNECTOR

monitors the high voltage power supply.

8.“CHECK MOTOR” Status LED indicates motor power status. pg 36

9.“BATTERY LOW” Status LED

indicates battery power status. pg 36

10.“POWER” Status LED

control board power status. pg 18,36

11.“MAGNETIC LOCK RELAY” Status LED status of this on-board relay. pg 34, 36

12.“MAGNETIC LOCK RELAY” Terminal Block connect electric locks here. pg 34, 36

13.INPUT STATUS LEDs

indicates input status. pg 36-37

14.ACCESS CONTROL TERMINAL BLOCKS accessory connections. pg 29-32, 42-44

15.“MASTER/SLAVE” Terminal Block wired master/slave connection. pg 22

16.CONTROL BOARD MOUNTING HOLES secures and grounds the control board.

17.“Siren” Terminal Block

Vikings UL Siren is connected here.

18.ON-BOARD 3 BUTTON STATION controls the gate during set up.

19.“AUX PWR” Terminal Block

used for solar applications & in-motion warning devices. pg 19, 25

20.FEATURE ACTIVATION PIN HEADERS activate features by placing a jumper onto the pin headers. pg 25

21.“DIAGNOSE” Button

allows you to navigate through the Diagnostics LCD Display. pg 38-40

22.“DIAGNOSE” LED

informs that errors have been detected and available on LCD Display. pg 38-40

23.LCD DIAGNOSTICS DISPLAY

provides error messages, diagnostics settings and operator status information. pg 38-40

24.EXPANSION PRODUCT CONNECTIONS connections for additional products from Viking Access Systems. pg 46

25.“FAIL SAFE/SECURE” Jumper

not applicable to this model.

26.NOT USED

27.FUSE HOLDER - 4 AMP for charging circuit.

28.HEAT SINK

secures the control board and dissipates heat.

4	VIKING TECHNICAL SUPPORT 1.800.908.0884

Image 6

Contents Instructions Viking Q-7 Slide Gate Operator Vehicular Gate Operator Revision Q7NXMN10.E December Parts Diagram DescriptionOperator References EMI Board Connector Control Board ReferencesTable of Contents Important Safety Information Important Safety InstructionsImportant Installation Instructions Important Installation Instructions Maintenance General Safety PrecautionsUL325 Gate Operator Classifications GlossaryPhoto Beam non-contact sensor Installation Secondary Entrapment ProtectionManual Release Edge Sensor contact sensor InstallationWhen manual operation is required To resume normal operationAudible Alarm Reset Switch Installation Manual Reset for the Audible AlarmSpecifications Single Phase 50Hz / 60HzLocate Control Buttons Gate Operator Installation Concrete Pad InstallationPositive Stop Installation Suggested Positive Stop TypesOperator Positioning Technical TIP Before completing the installation procedure StepElectrical Installation Tips for proper ground installationHigh Voltage Supply Option Electrical Installation Solar Supply OptionLimits Setup To Readjust the Close Limit To Readjust the Open LimitCable Requirements MASTER/SLAVE SetupTwo Wire Communication MS1 MS2Wireless Communication Options Required ADD-ONTimer Hold Open Timer Control Board SetupInitial Settings ODSAuto Open Power Failure Option Last Open Power Failure OptionObstruction Sensor Primary Entrapment Protection ODS Obstruction Detection SensorViking Lock Mode Viking HeaterThis page Left Blank Intentionally COM + Accessory ConnectionsRe-Open Photo Beam vehicular Safety Check for proper operationRadio Receiver Typical Open-Stop-CloseOpen Only Guard Station Anti-Tailgate, Open Commands & Guard StationOpen Commands ATG Anti-TailgateViking Loop Rack Accessory Connections Guidelines for Loop InstallationPower for the Locks Magnetic Lock, Lock SolenoidMagnetic Lock Lock Solenoid Synchronization with B-12 Barrier Arm B-12 Synchronization OptionTroubleshooting LED ReferencesTroubleshooting LCD MSG Meaning LCD Display ReferencesTroubleshooting Error Messages Solutions CheckAccess Control Connections Power ConnectionsGeneral Appendix aRelays In General Technical TIP Viking usesCommon Radio Receivers Connections Panels Appendix CSolar Applications Batteries & FuseViking Konnect Diagnostic Tool On-site remote Viking Expansion ProductsViking Konnect Master/Slave Kit Secure and reliable OUR Continuous Commitment to Excellence Standard Features