Hearth and Home Technologies ST-550TM-IPI owner manual Service Parts List, Stocked, At Depot

Page 60

Service Parts List			ST-550TM-IPI
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
1	Non-comb Board		2142-139
2	Basepan Ledge	Qty 2 req	2142-118
3	Refractory Panels	Qty 2 req	2142-117
4	Base Pan		2142-115
5	Glass Door Assembly		GLA-550TR	Y
6	Mesh Assembly	Qty 2 req	2142-031	Y
7	Burner Leg	Qty 2 req	2142-120
8	Burner NG, LP		2142-007	Y
9	Junction Box Bracket		2128-128
10	Junction Box		4021-013	Y

	Exhaust Restrictor		530-299
	Fiberglass Rope Ring		045-455
	Gasket Assembly
	Contains Vent, Seal Cap, Burner Neck, Shutter Bracket		2128-081
	and Valve Plate Gaskets

	Glass Latch Assembly	Qty 4 req	386-122A	Y
	Pilot Bracket		2142-124
	Surround Overlay (contains overlay for top, bottom and sides)		SRV2126-FACE
	Touch Up Paint		203-9

	Conversion Kit NG	NGK-550TM	Y
	Conversion Kit LP	LPK-550TM	Y
	Pilot Oriﬁce NG	593-528	Y
	Pilot Oriﬁce LP	593-527	Y
	Regulator NG	NGK-DXV	Y
	Regulator LP	LPK-DXF	Y

Additional service part numbers appear on following page.

60	Heat & Glo • ST-550TM-IPI • 2142-900 Rev. B • 11/08

Image 60

Contents Models What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideAppliance Setup TroubleshootingFinishing Reference MaterialsCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsGas Fireplace Safety Operating Instructions User GuideYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesClear Space Decorative Doors and FrontsLighting Instructions IPI Final inspection byFrequently Asked Questions After Fireplace is LitMaintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlPorcelain Firebox Panel Cleaning Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection VentingBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesNon-Combustible Mantel Fireplace OpeningTermination Locations Vent Termination Minimum ClearancesCovered Alcove Applications Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components Vent Information and Diagrams Approved PipeVent Table Key Use of ElbowsUse of Flex Vent Vent Diagrams Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum Top Vent Horizontal Termination Two Elbows V1 Minimum H1 + H2 MaximumTop Vent Horizontal Termination Three Elbows V1 Minimum H1 + H2 Maximum V1 + V2 MinExhaust restrictor Instructions Two Elbows Three Elbows Minimum Maximum + V 2 MinV1 Minimum Maximum V1 + V2 Min Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationInstall the Ceiling Firestop Pipe SLPInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Securing and Leveling the ApplianceInstalling Vent Pipe Assemble Vent SectionsAssemble Slip Sections Secure the Vent SectionsInstall Decorative Ceiling Components Disassemble Vent SectionsInstall Metal Roof Flashing Assemble and Install Storm CollarInstall RF4-8 Apply Sealant TOP & Partial SidesInstall Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap 22 Venting through the wallGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements Intelliﬁre Ignition System WiringOptional Accessories Requirements Electrical Service and RepairIntelliﬁre Ignition Wiring Diagram with Remote Receiver Junction Box Installation Wall Switch Installation for Fan OptionTo install the Splatter Guard FinishingSplatter Guard To Close the Lower Access Panel To Remove the Splatter GuardMantel and Wall Projections Combustible Mantel 15 Non-Combustible ZoneFacing Material Finishing MaterialWithout Front Shown Appliance Setup Install Trim Kits and Surrounds Air Shutter SettingTroubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Remove any contaminants that may have accumulated on Appliance Dimension Diagram Reference MaterialsVent Components Diagrams Snorkel Black Support Box-Black Wall Thimble-BlackAdapter SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP Service Parts ST-550TM-IPIService Parts List StockedAt Depot Intermittent Pilot Ignition Valve Assembly Contact Information