Hearth and Home Technologies ST-550TM-IPI Install RF4-8, Apply Sealant TOP & Partial Sides

Page 39

H. Install RF4-8

The RF4-8 may be used in place of the roof ﬂashing and storm collar (Sections 10.F. and 10.G.)

Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flashing. Refer to Section 10.C. Secure Vent Sections.

SECURE WITH 4

SCREWS NO LONGER

THAN 1 IN. (25 MM)

SLP-FS

Figure 10.15 Secure Pipe with SLP-FS

•Trim the rubber boot (using scissors or a utility knife), cutting along the marked measurement lines. See Figure 10.19. Use the 150 mm line.

•Lubricate pipe or ﬂue with water and slide the ﬂashing down. It may be necessary to trim the top shingles around the base of the rubber boot to ensure a good ﬁt.

•Draw around ﬂashing, remove.

•Apply silicone sealant to roof inside the lines (Figure 10.17).

•Lubricate pipe or ﬂue with water and slide ﬂashing down. Seat ﬁrmly in sealant. Nail roof ﬂashing to the roof.

•Apply silicone sealant on the top outside of the base plate on the sides and on top edge. See Figure 10.19. Install shingles, Apply sealant at the top edge of the rubber boot. See Figure 10.19.

•We recommend that you top coat with conventional acrylic house paint to improve the appearance of your galvanized base ﬂashing.

Figure 10.16 Trim Rubber Boot

Figure 10.17 Apply Sealant

APPLY SEALANT

TOP & PARTIAL SIDES

Figure 10.18 Slide Flashing Down, Secure & Apply Sealant

SILICONE SEALANT (TOP OF BOOT)

SHINGLES TRIMMED

	FLASHING OVER	SHINGLES OVER
	SHINGLES
		FLASHING

Figure 10.19 Installation Complete

Heat & Glo • ST-550TM-IPI • 2142-900 Rev. B • 11/08

39

Image 39

Contents What to do if you smell gas ModelsHomeowner Reference Information CongratulationsUser Guide Table of ContentsReference Materials Appliance SetupTroubleshooting FinishingCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsGas Fireplace Safety Operating Instructions User GuideYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear SpaceFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningVenting Porcelain Firebox Panel CleaningMaintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseFireplace Opening Non-Combustible MantelVent Termination Minimum Clearances Termination LocationsCovered Alcove Applications Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table KeyUse of Flex Vent Vent Diagrams Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Two ElbowsV1 Minimum H1 + H2 Maximum V1 + V2 Min Top Vent Horizontal Termination Three ElbowsExhaust restrictor Instructions Two Elbows Three Elbows Minimum Maximum + V 2 MinV1 Minimum Maximum V1 + V2 Min Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration FramingPipe SLP Install the Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Securing and Leveling the Appliance Appliance PreparationAssemble Vent Sections Installing Vent PipeSecure the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Install Decorative Ceiling ComponentsAssemble and Install Storm Collar Install Metal Roof FlashingApply Sealant TOP & Partial Sides Install RF4-8Install Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination 22 Venting through the wall Install Horizontal Termination CapGas Connection Gas InformationFuel Conversion Gas PressureElectrical Service and Repair Wiring RequirementsIntelliﬁre Ignition System Wiring Optional Accessories RequirementsIntelliﬁre Ignition Wiring Diagram with Remote Receiver Wall Switch Installation for Fan Option Junction Box InstallationTo install the Splatter Guard FinishingSplatter Guard To Remove the Splatter Guard To Close the Lower Access Panel15 Non-Combustible Zone Mantel and Wall Projections Combustible MantelFinishing Material Facing MaterialWithout Front Shown Appliance Setup Air Shutter Setting Install Trim Kits and SurroundsTroubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Remove any contaminants that may have accumulated on Reference Materials Appliance Dimension DiagramVent Components Diagrams Snorkel Black Support Box-Black Wall Thimble-BlackAdapter SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP ST-550TM-IPI Service PartsService Parts List StockedAt Depot Intermittent Pilot Ignition Valve Assembly Contact Information