C. Doors
Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. Once you have determined what kind of door and finishing material is going to be used on the fireplace, you may use the table below which shows the door mod- els and the finishing material thickness allowed. For an inside fit there is an available template to assist with siz- ing the finishing material.
|
| FINISH |
| |
DOOR | FIT | MATERIAL | SEE | |
MAXIMUM | FIGURE | |||
|
| |||
|
| THICKNESS |
| |
Folio | Inside | Any | 13.4 | |
Arcadia | Overlap | 1 inch | 13.5 | |
Inside | Any | 13.6 | ||
| ||||
Halston | Overlap | 1 inch | 13.5 | |
Inside | 1 inch - 3 inch | 13.7 | ||
| ||||
Chateau | Overlap | 1 inch | 13.5 | |
Inside | Any | 13.6 | ||
| ||||
Valencia | Overlap | 1 inch | 13.5 | |
Inside | Any | 13.6 | ||
| ||||
Galleria | Overlap | 1 inch | 13.5 | |
Inside | 1 inch - 3 inch | 13.7 | ||
|
| ELBOW |
|
FINISHING | HEAT | FINISHING |
MATERIAL | SHIELD | MATERIAL |
|
DOOR
37 in.
(Outside door width)
(Includes 1/8 in. opening each side of door)
34 in. | ||
37 in. | ||
| ||
(Outside door width) |
| |
|
(Includes 1/8 in. opening each side of door)
Finishing materials over 1 inch thick.
Figure 13.6 Inside fit door
ELBOW
HEAT
SHIELD
Stop finishing material flush with opening.
Figure 13.4 Folio Door
Finishing materials 1 inch maximum thick. Stop finishing material flush with opening.
Figure 13.5 Overlap Fit Door
FINISHING | FINISHING |
MATERIAL | MATERIAL |
*IF FINISHING MATERIAL IS THICKER THAN
2 IN., DOORS WILL ONLY OPEN
AS FAR AS PICTURED
DOORS
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 33 3/4 |
|
|
|
|
|
|
|
|
| 34 IN. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| IN. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
37 1/4 IN.
Finishing material between 1 and 3 inches thick.
Figure 13.7 Operable hinge door
Heat & Glo • | 51 |