Hearth and Home Technologies CASTILE-CSB, CASTILE-MBK1, CASTILE-PMH1, CASTILE-CWL Optional TOP LOG

Page 19

R

Castile Pellet Stove

E. Optional Log Set Placement Instructions

CAUTION

Logs are FRAGILE. Use extreme care when handling or cleaning logs.

4 PIECE LOG SET INSTALLATION

1.

Open the hinged cast face and open the glass door

 

 

 

 

assembly.

 

 

 

2.

To position the logs, place the right rear log as shown in

Figure 19.3

 

 

Figure 19.1. There is a notch in the bottom of the log for

 

 

 

 

clearance for the thermocouple and thermocouple cover

 

 

 

 

(ceramic protection tube).

 

 

 

 

 

 

 

3.Continue placing the last 3 logs around the firepot as show in Figures 19.2, 19.3 and 19.4. Be careful not to block the drop tube in the back of the firebox where pel- lets feed into the firepot.

Notch

Thermocouple

Cover

Figure 19.1

Drop Tube

Figure 19.2

NOTE:

Due to the abrasive nature of a pellet appliance fire, the logs are not covered under warranty. Any placement varia- tion other than shown here can cause excessive heat and shall void the appliance warranty.

Figure 19.4

OPTIONAL TOP LOG

Place the log over the firepot. The charred area on the back of the log is turned toward the back, not the front.

The log will be about 2-1/2 inches above the firepot when in place. It must rest on the 3 logs in a stable position to prevent it from falling into the firepot.

Figure 19.5

September 1, 2008

250-6422E

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Castile Pellet Stove Location Back side of left side panel Castile Pellet StoveTable of Contents Listing and Code Approvals Appliance Location Design, Installation & Location ConsiderationsFire Safety Getting StartedInspect Appliance & Components and Pre-Use Check List Castile Pellet Stove Tools And Supplies NeededFire Risk Appliance Dimensions 3Dimensions and ClearancesCastile Pellet Stove Clearances to Combustibles UL and ULC Castile Pellet Stove Hearth Pad Requirements UL and ULC Exception for Horizontal InstallationsHearth Pad Requirements Chimney and Exhaust Connection 4Vent InformationVenting Termination Requirements See Figure Pipe Selection ChartCastile Pellet Stove Equivalent Feet of Pipe Example of 3 Elbow-Rear Vent Termination CalculatonAlcove 5Venting SystemsDegree Straight OutCastile Pellet Stove Through The Wall Through The Wall & Vertical Castile Pellet Stove VerticalAlternate Masonry Castile Pellet Stove Masonry6Mobile Home Outside Air Kit Instructions 7Appliance Set-UpCastile Pellet Stove Leg Leveling System Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation Installing the Top Vent AdapterOptional TOP LOG Castile Pellet Stove Thermostat Installation Fuel Size And Material General Operating Information 8Operating InstructionsStarting Your First Fire Fire CharacteristicsFeed Rate Adjustment Instructions Castile Pellet Stove Before Your First FireCastile Pellet Stove Iginition Cycles Frequently Asked QuestionsSymption TroubleshootingPossible Cause Corrective Action Page Symptoms Possible Cause Corrective Action Daily Weekly Monthly Yearly Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance FrequencyAsh Removal from Firebox Cleaning Firepot with Cleaning Rod & Firepot ScraperCleaning Ash Pan Cleaning Heat Exchanger Chambers & Drop TubeCleaning the Glass Cleaning Beneath Heat ExchangerCleaning the Exhaust Path Cleaning the HopperPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning Convection Blower Requires No LubricationCleaning Exhaust Blower Requires No Lubrication Cleaning the Top Vent AdapterConvection Blower Replacement Castile Pellet Stove High Ash Fuel Content MaintenanceRemove 6 screws Combustion Blower Combustion Blower ReplacementIgniter Replacement Glass Replacement Component Function Snap Disc #2 Fuel Delivery Interrupt 250F Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 110FCastile Pellet Stove Component Locations Description Part Number Castile Pellet Stove Exploded ViewsPart Description Service Parts Castile Pellet Stove Service Parts and AccessoriesCastile Pellet Stove Appliances AccessoriesDate of Service Performed By Description of Service Castile Pellet Stove Service and Maintenance LogCastile Pellet Stove Service and Maintenance Log Cont’d Castile Pellet Stove Homeowner’s Notes EPA Castile Pellet Stove Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d Telephone T O T O

CASTILE-PMH1, CASTILE-CSB, CASTILE-MBK1, CASTILE-CWL specifications

Hearth and Home Technologies is renowned for its innovative and efficient heating solutions, among which the CASTILE line of products stands out. The CASTILE-CWL, CASTILE-MBK1, CASTILE-CSB, and CASTILE-PMH1 represent a blend of tradition and modern technology, designed to enhance home comfort while prioritizing energy efficiency and ease of use.

The CASTILE-CWL is a versatile unit featuring a sleek design that fits effortlessly into various decors. It incorporates an advanced combustion system that promotes cleaner burning, reducing emissions while delivering robust heat output. Its large hopper capacity minimizes the frequency of refueling, making it ideal for continuous heating. Additionally, the intuitive control panel offers user-friendly operation, allowing homeowners to set their ideal temperature easily.

Next, the CASTILE-MBK1 model boasts a unique design compatible with many different settings. It features enhanced insulation that ensures maximum heat retention and minimizes heat loss. The automatic ignition and advanced safety features ensure that use is not only efficient but also worry-free. Moreover, this model includes a programmable thermostat, giving users the ability to set heating schedules according to their preferences.

The CASTILE-CSB is particularly notable for its integration of modern technology with traditional aesthetics. Its compact design doesn’t skimp on performance, and its high-efficiency rating translates to lower energy bills. With features like a quiet operation system and a digital display for monitoring, the CASTILE-CSB is perfect for homes of any size. The model also offers customizable options for different finishes, allowing homeowners to match their heating source with their interior design.

Finally, the CASTILE-PMH1 rounds out this impressive lineup. This model is designed for reliable performance, providing consistent warmth with its state-of-the-art heat exchanger technology. The chimney venting system enables optimal heat distribution throughout the home while maintaining safety standards. Additionally, it includes features such as an easy-clean design and multiple heat settings, allowing users to tailor their heating experience.

In summary, Hearth and Home Technologies’ CASTILE product line offers an impressive combination of style, efficiency, and advanced features. Each model caters to specific needs while upholding the brand's commitment to quality and innovation, ensuring homeowners can enjoy a warm and inviting living environment.
Top Page Image Contents