Hearth and Home Technologies CASTILE-CWL Castile Pellet Stove Tools And Supplies Needed

Page 6

R

Castile Pellet Stove

C. Tools And Supplies Needed

Tools and building supplies normally required for installation, unless installing into an existing masonry fireplace:

Reciprocating Saw

Safety Glasses

Channel Locks

Framing Square

Hammer

Electric Drill & Bits (1/4”)

Phillips Screwdriver

1/4” Self-Tapping Screws

Tape Meausre

 

Plumb Line

May also need:

Level

Vent Support Straps

Framing Material

Venting Paint

Hi-temp Caulking Material

 

Gloves

 

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components.

Report damaged parts to dealer.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance.

Modification of the appliance.

Installation other than as instructed by Hearth & Home Technologies.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Operating appliance without fully assembling all components.

Operating appliance without legs attached (if supplied with unit).

Do NOT Overfire

Or any such action that may cause a fire hazard.

D. Inspect Appliance & Components and Pre-Use Check List

1.

 

Place the appliance in a location near the

 

 

final installation area and follow the proce-

 

 

dures below:

2.

 

Open the appliance and remove all the parts

 

 

and articles packed inside the Component

 

 

Pack. Inspect all the parts and glass for ship-

 

 

ping damage. Contact your dealer if any irregu-

 

 

larities are noticed.

3.

 

All safety warnings have been read and fol-

 

 

lowed.

4.

 

This Owner’s Manual has been read.

5.

 

Floor protection requirements have been met.

6.

 

Venting is properly installed.

7.

 

The proper clearances from the appliance and

 

 

chimney to combustible materials have been

 

 

met.

8.

 

The masonry chimney is inspected by a profes-

 

 

sional and is clean, or the factory built metal

 

 

chimney is installed according to the manufac-

 

 

turer’s instructions and clearances.

9.

 

The chimney meets the required minimum

 

 

height.

10.

 

All labels have been removed from the glass

 

 

door.

11.

 

Plated surfaces have been wiped clean, if

 

 

applicable.

12.

 

Thermostat or remote has been installed.

13.

 

A power outlet is available nearby.

Page 6

250-6422E

September 1, 2008

Image 6
Contents Castile Pellet Stove Castile Pellet Stove Location Back side of left side panelTable of Contents Listing and Code Approvals Getting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCastile Pellet Stove Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check ListFire Risk 3Dimensions and Clearances Appliance DimensionsCastile Pellet Stove Clearances to Combustibles UL and ULC Exception for Horizontal Installations Castile Pellet Stove Hearth Pad Requirements UL and ULCHearth Pad Requirements 4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Example of 3 Elbow-Rear Vent Termination Calculaton Pipe Selection ChartCastile Pellet Stove Equivalent Feet of Pipe See Figure5Venting Systems AlcoveStraight Out DegreeCastile Pellet Stove Through The Wall Castile Pellet Stove Vertical Through The Wall & VerticalCastile Pellet Stove Masonry Alternate Masonry6Mobile Home 7Appliance Set-Up Outside Air Kit InstructionsInstalling the Top Vent Adapter Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation Castile Pellet Stove Leg Leveling SystemOptional TOP LOG Castile Pellet Stove Thermostat Installation 8Operating Instructions Fuel Size And Material General Operating InformationCastile Pellet Stove Before Your First Fire Fire CharacteristicsFeed Rate Adjustment Instructions Starting Your First FireFrequently Asked Questions Castile Pellet Stove Iginition CyclesTroubleshooting SymptionPossible Cause Corrective Action Page Symptoms Possible Cause Corrective Action Frequency Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Daily Weekly Monthly YearlyCleaning Heat Exchanger Chambers & Drop Tube Cleaning Firepot with Cleaning Rod & Firepot ScraperCleaning Ash Pan Ash Removal from FireboxCleaning the Hopper Cleaning Beneath Heat ExchangerCleaning the Exhaust Path Cleaning the GlassCleaning the Top Vent Adapter Cleaning Convection Blower Requires No LubricationCleaning Exhaust Blower Requires No Lubrication Preparing Firebox for Non-Burn Season Frequency YearlyCastile Pellet Stove High Ash Fuel Content Maintenance Convection Blower ReplacementCombustion Blower Replacement Remove 6 screws Combustion BlowerIgniter Replacement Glass Replacement Component Function Snap Disc #1 Convection Blower 110F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Stove Component Locations Castile Pellet Stove Exploded Views Description Part NumberPart Description Castile Pellet Stove Service Parts and Accessories Service PartsCastile Pellet Stove Accessories AppliancesCastile Pellet Stove Service and Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Stove Service and Maintenance Log Cont’d Castile Pellet Stove Homeowner’s Notes Castile Pellet Stove Warranty Policy EPAHearth & Home Technologies Limited Warranty Cont’d T O T O Telephone

CASTILE-PMH1, CASTILE-CSB, CASTILE-MBK1, CASTILE-CWL specifications

Hearth and Home Technologies is renowned for its innovative and efficient heating solutions, among which the CASTILE line of products stands out. The CASTILE-CWL, CASTILE-MBK1, CASTILE-CSB, and CASTILE-PMH1 represent a blend of tradition and modern technology, designed to enhance home comfort while prioritizing energy efficiency and ease of use.

The CASTILE-CWL is a versatile unit featuring a sleek design that fits effortlessly into various decors. It incorporates an advanced combustion system that promotes cleaner burning, reducing emissions while delivering robust heat output. Its large hopper capacity minimizes the frequency of refueling, making it ideal for continuous heating. Additionally, the intuitive control panel offers user-friendly operation, allowing homeowners to set their ideal temperature easily.

Next, the CASTILE-MBK1 model boasts a unique design compatible with many different settings. It features enhanced insulation that ensures maximum heat retention and minimizes heat loss. The automatic ignition and advanced safety features ensure that use is not only efficient but also worry-free. Moreover, this model includes a programmable thermostat, giving users the ability to set heating schedules according to their preferences.

The CASTILE-CSB is particularly notable for its integration of modern technology with traditional aesthetics. Its compact design doesn’t skimp on performance, and its high-efficiency rating translates to lower energy bills. With features like a quiet operation system and a digital display for monitoring, the CASTILE-CSB is perfect for homes of any size. The model also offers customizable options for different finishes, allowing homeowners to match their heating source with their interior design.

Finally, the CASTILE-PMH1 rounds out this impressive lineup. This model is designed for reliable performance, providing consistent warmth with its state-of-the-art heat exchanger technology. The chimney venting system enables optimal heat distribution throughout the home while maintaining safety standards. Additionally, it includes features such as an easy-clean design and multiple heat settings, allowing users to tailor their heating experience.

In summary, Hearth and Home Technologies’ CASTILE product line offers an impressive combination of style, efficiency, and advanced features. Each model caters to specific needs while upholding the brand's commitment to quality and innovation, ensuring homeowners can enjoy a warm and inviting living environment.