Hearth and Home Technologies CASTILE-MBK1 Castile Pellet Stove Thermostat Installation

Page 20

R

Castile Pellet Stove

F. Thermostat Installation

1. A 12 volt AC thermostat is required to operate this pellet appliance. You may use the included wall mount thermo- stat or purchase an optional programmable thermostat or remote control. It is equipped with an adjustable heat anticipator. The current rating is .05 amps. The anticipator needs to be adjusted to the lowest setting available.

2.When mounting a thermostat on a wall, be sure to follow your thermostat installation instructions carefully.

NOTE: Thermostat must be mounted level for accurate readings. The thermostat should be mounted on an inside wall and not in direct line with the appliance convection air.

NOTE: If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home.

3.There is a 4 screw terminal block located on the back lower right corner of the stove directly above the power cord inlet. The center 2 screws are for the thermostat wires.

FUSE

Fuse

TERMINAL BLOCK

CENTER 2 SCREWS FOR

THERMOSTAT WIRES

POWER OUTLET

Figure 20.1

CAUTION

Shock hazard.

•Do NOT remove grounding prong from plug.

•Plug directly into properly grounded 3 prong receptacle.

•Route cord away from appliance.

•Do NOT route cord under or in front of appliance.

Page 20

250-6422E

September 1, 2008

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Castile Pellet Stove Castile Pellet Stove Location Back side of left side panelTable of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationFire Risk Castile Pellet Stove Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsCastile Pellet Stove Clearances to Combustibles UL and ULC Hearth Pad Requirements Exception for Horizontal InstallationsCastile Pellet Stove Hearth Pad Requirements UL and ULC Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Pipe Selection Chart Castile Pellet Stove Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculaton See Figure5Venting Systems AlcoveCastile Pellet Stove Through The Wall Straight OutDegree Castile Pellet Stove Vertical Through The Wall & VerticalCastile Pellet Stove Masonry Alternate Masonry6Mobile Home 7Appliance Set-Up Outside Air Kit InstructionsTop Vent Adapter Installation Rear Vent and Rear Vent to Top Vent Adapter InstallationInstalling the Top Vent Adapter Castile Pellet Stove Leg Leveling SystemOptional TOP LOG Castile Pellet Stove Thermostat Installation 8Operating Instructions Fuel Size And Material General Operating InformationFire Characteristics Feed Rate Adjustment InstructionsCastile Pellet Stove Before Your First Fire Starting Your First FireFrequently Asked Questions Castile Pellet Stove Iginition CyclesPossible Cause Corrective Action TroubleshootingSymption Page Symptoms Possible Cause Corrective Action Quick Reference Maintenance Chart 10Maintaining & Servicing Your ApplianceFrequency Daily Weekly Monthly YearlyCleaning Firepot with Cleaning Rod & Firepot Scraper Cleaning Ash PanCleaning Heat Exchanger Chambers & Drop Tube Ash Removal from FireboxCleaning Beneath Heat Exchanger Cleaning the Exhaust PathCleaning the Hopper Cleaning the GlassCleaning Convection Blower Requires No Lubrication Cleaning Exhaust Blower Requires No LubricationCleaning the Top Vent Adapter Preparing Firebox for Non-Burn Season Frequency YearlyCastile Pellet Stove High Ash Fuel Content Maintenance Convection Blower ReplacementCombustion Blower Replacement Remove 6 screws Combustion BlowerIgniter Replacement Glass Replacement Component Function Vacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Stove Component Locations Castile Pellet Stove Exploded Views Description Part NumberPart Description Castile Pellet Stove Service Parts and Accessories Service PartsCastile Pellet Stove Accessories AppliancesCastile Pellet Stove Service and Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Stove Service and Maintenance Log Cont’d Castile Pellet Stove Homeowner’s Notes Castile Pellet Stove Warranty Policy EPAHearth & Home Technologies Limited Warranty Cont’d T O T O Telephone

CASTILE-PMH1, CASTILE-CSB, CASTILE-MBK1, CASTILE-CWL specifications

Hearth and Home Technologies is renowned for its innovative and efficient heating solutions, among which the CASTILE line of products stands out. The CASTILE-CWL, CASTILE-MBK1, CASTILE-CSB, and CASTILE-PMH1 represent a blend of tradition and modern technology, designed to enhance home comfort while prioritizing energy efficiency and ease of use.

The CASTILE-CWL is a versatile unit featuring a sleek design that fits effortlessly into various decors. It incorporates an advanced combustion system that promotes cleaner burning, reducing emissions while delivering robust heat output. Its large hopper capacity minimizes the frequency of refueling, making it ideal for continuous heating. Additionally, the intuitive control panel offers user-friendly operation, allowing homeowners to set their ideal temperature easily.

Next, the CASTILE-MBK1 model boasts a unique design compatible with many different settings. It features enhanced insulation that ensures maximum heat retention and minimizes heat loss. The automatic ignition and advanced safety features ensure that use is not only efficient but also worry-free. Moreover, this model includes a programmable thermostat, giving users the ability to set heating schedules according to their preferences.

The CASTILE-CSB is particularly notable for its integration of modern technology with traditional aesthetics. Its compact design doesn’t skimp on performance, and its high-efficiency rating translates to lower energy bills. With features like a quiet operation system and a digital display for monitoring, the CASTILE-CSB is perfect for homes of any size. The model also offers customizable options for different finishes, allowing homeowners to match their heating source with their interior design.

Finally, the CASTILE-PMH1 rounds out this impressive lineup. This model is designed for reliable performance, providing consistent warmth with its state-of-the-art heat exchanger technology. The chimney venting system enables optimal heat distribution throughout the home while maintaining safety standards. Additionally, it includes features such as an easy-clean design and multiple heat settings, allowing users to tailor their heating experience.

In summary, Hearth and Home Technologies’ CASTILE product line offers an impressive combination of style, efficiency, and advanced features. Each model caters to specific needs while upholding the brand's commitment to quality and innovation, ensuring homeowners can enjoy a warm and inviting living environment.
Top Page Image Contents