Hearth and Home Technologies CB1200-B Cleaning Beneath Heat Exchanger Door Latch Inspection

Page 30

R

CB 1200 Pellet Stove

7. Cleaning Beneath Heat Exchanger

10. Door Latch Inspection

 

•Frequency: Monthly or after burning 1 ton of fuel

•By: Homeowner

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off

.b. A more thorough cleaning is needed to remove the excess ash that is left behind from the use of the cleaning rods for the heat exchanger tubes.

c.The ash will be resting on the back of the baffles. This will require removing the baffles. Please refer to page 33 for instructions on removing the baffles.

8.Cleaning Exhaust Path

•Frequency: Yearly or more frequently depending on ash build-up.

•By: Homeowner

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off

b.Open the hinged access door on the left of the appli- ance.

c.Reach in and unlatch the trap door that is connected to the rear of exhaust blower.

d.Use a small vacuum hose attachment to clean area.

e.Re-latch and close trap door.

NOTE: There are heavy duty vacuum cleaners specifically designed for solid fuel appliance cleaning.

•Frequency: Prior to heating season

•By: Homeowner

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off

b.To adjust, open the latch and pivot the holding rod out. Loosen the jam nut on the rod.

c.With a Phillips head screw driver, turn the rod clockwise to tighten. The latch handle should snap securely in place when adjusted properly.

d.After adjusting the latch, be sure to tighten the jam nut on the rod to hold the adjustment.

11.Door Gasket Inspection

•Frequency: Prior to heating season

•By: Homeowner

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off

b.To inspect the door rope (gasket), open the door and see that the door rope extends approximately 1/8 inch (3mm) to 3/16 inch (9.5mm) from the door rope chan- nel.

c.It should show signs of compaction all the way around the door where the rope contacts the face of the appli- ance. Confirm there are no air leaks.

12.Cleaning the Hopper

9.Cleaning the Glass

•Frequency: When clear view of the firepot becomes obscure.

•By: Homeowner

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off.

b.Use a damp paper towel or any nonabrasive glass cleaner. Wipe off with dry towel.

CAUTION

Handle glass assembly with care.

When cleaning glass:

• Avoid striking, scratching or slamming glass.

•Do NOT clean glass when it is hot.

•Do NOT use abrasive cleaners.

•Use a hard water deposit glass cleaner on white film.

•Refer to maintenance instructions.

•Frequency: Monthly or after burning 1 ton of fuel

•By: Homeowner

After burning approximately 1 ton of fuel or changing fuels you will need to clean the hopper to prevent saw- dust build-up.

A combination of sawdust and pellets on the auger reduces the amount of fuel supply to the firepot. This can result in nuisance shutdowns and mis-starts.

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off.

bEmpty the hopper of any remaining pellets.

c. Vacuum the hopper and feed tube.

13.Cleaning Exhaust Blower - Requires No Lubrication

•Frequency: Yearly or as needed

•By: Quality Service Technician/Homeowner

•Task:: Contact your local dealer.

14.Cleaning Convection Blower - Requires No Lubrication

• Frequency: Yearly or as needed

• By: Qualified Service Technician

• Task: Contact your local dealer.

Page 30

7014-082D

September 1, 2008

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Classic BAY 1200 Pellet Stove Hot glass will cause burnsTesting Lab & Report Number Serial Number Model Mfg Date CB 1200 Pellet StoveBehind left side curtain on outside of hopper wall Table of Contents Listing and Code Approvals Getting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCB 1200 Pellet Stove Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check List3Dimensions and Clearances Appliance DimensionsCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Exception for Horizontal Installations CB 1200 Pellet Stove Hearth Pad Requirements UL and ULCHearth Pad Requirements 4Vent Information Example of 3 Elbow-Rear Vent Termination Calculaton Pipe Selection ChartCB 1200 Pellet Stove Equivalent Feet of Pipe Example5Venting Systems AlcoveStraight Out DegreeCB 1200 Pellet Stove Through The Wall CB 1200 Pellet Stove Vertical Through The Wall & VerticalMasonry Alternate Masonry6Mobile Home Rear Installation Floor Installation 7Appliance Set-UpOutside Air Kit Instructions Installing the Top Vent Adapter CB 1200 Pellet Stove Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation See FigureInstalled Clip Top Log, Left Installing Logo Nickel OnlyCharred Areas in the Back RightTo install door CB 1200 Pellet Stove Door InstallationThermostat Installation To adjust latches8Operating Instructions Fuel Size And Material General Operating InformationFeed Rate Adjustment Instructions Starting Your First FireFrequently Asked Questions Button. See .1, page 22 . When you pressCB 1200 Pellet Stove Ignition Cycles Troubleshooting SymptomPossible Cause Corrective Action Page Page 10Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Frequency Daily Weekly Monthly YearlyCleaning Heat Exchanger Chambers & Drop Tube Cleaning Firepot with Cleaning Rod & Firepot ScraperCleaning Ash Pan Ash Removal from FireboxCleaning the Hopper Cleaning the Glass Cleaning Beneath Heat Exchanger Door Latch InspectionCleaning Exhaust Path Cleaning Exhaust Blower Requires No LubricationCleaning the Top Vent Adapter Preparing Firebox for Non-Burn Season Frequency YearlyCB 1200 Pellet Stove High Ash Fuel Content Maintenance Convection Blower ReplacementExhaust Blower Replacement Remove existing blower Install new blowerRe-install blower to blower housing Glass Replacement Replacing Side Glass ScrewsReference Materials Component Function & LocationSnap Disc #1 Convection Blower 145F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Thermostat Override 200FCB 1200 Pellet Stove Component Locations CB 1200 Pellet Stove Exploded Views Glass Size Center 13-7/8 wide x 11 highGlass Size Sides 8 wide x 11 high Nbr Description CB 1200 Pellet Stove CB 1200 Pellet Stove Service Parts and Accessories Item # Parts Alphabetical OrderItem # Service Parts Alphabetical Order Accessories ApplianceCB 1200 Pellet Stove Service And Maintenance Log Date of Service Performed By Description of ServiceCB 1200 Pellet Stove Homeowner’s Notes CB 1200 Pellet Stove Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information
Top Page Image Contents