Sears 139.53960SRT Determine the Header Bracket Location, Sectional Door ONE-PIECEDOOR with Track

Page 12

INSTALLATION STEP 1

Determine the Header Bracket Location

To preventpossibleSERIOUSiNJURYor DEATH:

•HeaderbracketMUSTbe RIGIDLYfastenedto structural support on headerwall or ceiling,otherwise garagedoor might not reversewhen required.DO NOT install headerbracketover drywall

•ConcreteanchorsMUST beused if mounting header bracketor 2x4 into masonry,

•NEVERtry to loosen, moveor adjust garagedoor,

springs, cables,pulleys, brackets,or their hardware,all of which areunder EXTREMEtension.

•ALWAYScall atrained door systemstechnicianif garagedoor binds,sticks, or is out of balance.An unbalancedgaragedoor might not reversewhen required.

Installation procedures vary according to garage door types. Follow the instructions which apply to your door.

SECTIONAL DOOR

AND ONE-PIECEDOOR WITH TRACK

1.Close the door and mark the inside vertical centerline of the garage door.

2.Extend the line onto the header wall above the door.

You can fasten the header bracket within 4 feet of the left or right of the door center only if a torsion spring or center bearing plate is in the way; or you can attach it to the ceiling (see page 14) when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain approximately 1/2".)

If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not provided) to securely fasten the 2x4 to structural supports as shown here and on page 13.

3.Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point, This height will provide travel clearance for the top edge of the door.

Vertical

Centerline

Ceiling

I

Header Wall

._L--_2" Track

Highest Point

of Travel

--DoOr

__ Finished-

Ceiling

2x4 StrucJural

Sectional door with curved track

Header Wall

Track

'--2"

NOTE: Door clearance brackets are available for sectional doors when headroom clearance is less

than 2". See accessory page 39.

Proceed to Step 2, page 14.

One-piece

of Travel

door with

 

horizontal

 

track

 

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Garage Door Opener Abridor DE Puerta DE Cochera 4tI Warning Preparing your garage door Sectional Door One-Piece DoorTools needed Level DrillSectional Door Installation Sectional Door InstallationsPlanning Closed PositionONE-PIECE Door Installations ONE-PIECE Door Without TrackONE-PIECE Door with Track Finished CeilingCarton Inventory Assembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Back RailsTo Motor Unit Install the Idler Pulley Hardware Shown Actual SizeOn TOP and Sides Bracket Inside Dispensin9 Master Link CapSha SprocketTighten the Chain ChainII/2 Inch Base fRail Mid length of RailDetermine the Header Bracket Location Sectional Door ONE-PIECEDOOR with TrackProceed to , Example Proceed toStepOne-piece door without track jamb hardware One-piece door without track pivot hardwareWall Header Bracket Installation Ceiling Header Bracket InstallationAttach the Rail to the Header Bracket HoleTempora Suppo Position the Opener Sectional Door or ONE-PIECE Door with TrackONE-PIECEDOOR Without Track EngagedreleasedStrJctural HardwareshownactualsizeInstall the Door Control Outside Keylock Accessory ConnectionsLlilllllliltltl Illliillllil Attach the Emergency Release Rope and Handle Lens GuideOverhand Reinstall the cover Permanent Wiring ConnectionElectrical Requirements Ground Tab Green Ground ScrewInstall The Safety Reversing Sensor Important Information about Safety Reversing SensorFacing the door from inside the garage Above floorInstalling the Brackets Garage door track installation preferredWall installation Floor installationMounting and Wiring the Safety Sensors Figure Aligning the Safety SensorsTroubleshooting the Safety Sensors Opener Terminal ScrewsFasten the Door Bracket Sectional DoorsBracket IIIIIIIIIIIIIIIIIIII!IIIIIII!IIIIIINut5,16HiiBo,tLkwa6r ONE-PIECE DoorsConnect Door Arm to Trolley Sectional Doors onlyAdjustment procedures, Figure Closed door adjustment decrease Down travel limitAssemble the door arm, Figure ALL ONE-PIECE DoorsAdjust the UP and Down Travel Limits HOW and When to Adjust the LimitsAdjust the UP open force as explained in Adjustment Step If door does not open at least 5 feetAdjust the Force HOW and When to Adjust the ForcesTest the Down close force Test the UP open forceTest the Safety Reversal System AdjustImportant Safety Check Test the Safety Reversing SensorImportant Safety Instructions Using Your Garage Door OpenerUsing the Wall.Mounted Door Control Light featureLock feature To Open the Door ManuallyCare Your Opener Twice a YearOnce a Year Having a Problem? Using the Learn Button To Add an Additional Hand.held RemoteControl To Erase All Codes From Motor Unit MemoryUsing the Learn Button To Add or Change a Keyless Entry PINRail Assembly Parts Installation PartsKEY Part NO. NO.DESCRIPTION KEY Part DescriptionMotor Unit Assembly Parts Limit Switch1817 Not ShownAvailable only through Sears Parts & Service Sears WarrantyAccesorios GarantiaNbmeros Servicio Contra Tapa IntroduccionPreparaci6n de la puerta de su cochera Puerta seccional Puerta de una sola piezaHerramientas NecesariasPlanificacien Instalacion CON UNA Puerta SeccionalFesortede torsi n Control dl La puertaPlanificaci6n continba Puerta DE UNA Sola Pieza SIN CarrilInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Pieza CON CarrilInventario de las cajas 53970,5393Entrada sin Ilave Reversa de segurdadun ojo transmisorInventario de piezas TORNILLERiA Y Piezas Para LA InstalacionTORNILLERiA Y Piezas Para EL Armado Monte el riel e instale el trole LA PuertaMONTAJE, Paso Instale la polea IocaSujete el riel al motor Estas Piezas SE Muestran /..= EN SU Tamaio NormalInstale la cadena o cable y coloque La cubierta de la polea Apriete la cadena ParaercaapretarinternaDetermine dnde va a instalar La mnsula del cabeza Puerta Seccional Puerta DE UNA Sola Pieza CON CarrilContinUe con el Paso 2, paglna Puerta de una pieza sin carril tornilleria del pivote Puerta DE UNA Sola Pieza SIN CarrilEjemplo SumeInstale la mnsula del cabezal Instalacion DE LA M#NSULA DEL Cabezal EN LA Pared DelanteraInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Coloque el riel en la mnsula del cabezal Con unEstas Piezas SE Muestran EN SU Tamaio Normal Coloque el abridor Puerta Seccional O Puerta DE UNA Sola Peza CON CarrilPJL Trole ixterno Trie interno INSTALACION,PASO Cuelgue el abridorFgura Instale la unidad de control Premium No apriete en excesoFlgura Instale la luce y lente Coloque la cuerda y la manija de emergenciaINSTALACION, Paso Requisitos para la instalaci6n elctricaConexioncon Cableado Permanente LangetaInstale el sensor del sistema de Reversa de seguridad Vista de la puerta desde el interior de la cocheraFstas Piezas SE Muestran EN SU Tamaio Normal Montaje Y Cableado DE LOS Sensores DEL Sistema DE Reversa DE SeguridadCMO Alinear LOS Sensores DE Seguridad Las terminales del abridor Cabe de campanaSujete la mnsula de la puerta UraPuertas Seccionales Si su puerta es de metal, aluminioPuertas DE UNA Sola Pieza Cielo rasoDe pulgadaRoldana de 5/16 de pulgada Conecte el brazo de la puerta al trole Solo Para Puertas SeccionalesEstas Piezas SE Muestran EN SU Tamano Normal Arme el brazo de la puerta, Figura Procedimiento de ajuste, FiguraConecte el brazo de la puerta al trole Posicion Completamente CerradaAjuste el Iimite del recorrido hacia Arriba y hacia abajoRecorrldo COMe Y Cuando Ajustar LOS LiMITESAjuste la fuerza Como Y Cuando Ajustar LA Fuerza DEL AbridorPruebe la fuerza del recorrido hacia abajo cerrar Pruebe la fuerza del recorrido hacia arriba abrirAJUSTES, Paso Pruebe el sensor del sistema de reversa de seguridadPruebe el sistema de reversa de seguridad Cno usar su abridor de puerta de cochera Active su abridor de alguna de las siguientes manerasC6mo usar la unidad de control de pared Cdmo abrir la puerta manualmenteSeguro Mantenimiento De su abridor de puerta De cochera LA Bateriadel ControlremotoCalendario DE Mantenimiento Dos veces al aoSi tiene algbn problema El control remote tiene corto alcanceCbmo agregar un control remoto manual adicionaJ Como Usarel BOT3NAPRENDER LearnControles remotos de 3 funciones Todos los cSdigosPara poner o cambiar el PIN de la Entrada sin Ilaves Pies se abra completarnente Control remoto compacto de 3 funcionesEntrada sin Ilave de funciones mOltiples Mdnsulas de extensi6nWww, sears.com LE-FOYER

139.53960SRT, 139.53968SRT, 139.53971SRT specifications

Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT are a series of garage door openers that have gained recognition for their reliability and advanced features. These models represent a shift towards smarter technology in home automation, providing homeowners with increased convenience, security, and control over their garage doors.

One of the standout features of these models is their Smart Technology integration. Each unit is equipped with the ability to connect to Wi-Fi, allowing users to control their garage doors remotely through a smartphone app. This means that you can open or close your garage door from anywhere, check its status, and receive notifications if the door is left open for an extended period. This feature enhances home security by providing real-time updates, giving users peace of mind when they are away from home.

The 139.53971SRT model is designed with a powerful motor that ensures smooth and quiet operation, making it suitable for homes with bedrooms adjacent to the garage. It features a built-in battery backup system, which is crucial during power outages, providing peace of mind that your garage door can still be operated.

Meanwhile, the 139.53968SRT and 139.53960SRT models come with a range of safety features such as the security keypad and 3-button remote control, which allow multiple users to gain access without the need for a physical key. The Smart Technology also incorporates advanced encryption protocols that help prevent unauthorized access, ensuring the garage remains secure.

Additionally, all three models are designed for easy installation and come with a variety of installation accessories. Their adaptability makes them compatible with a wide range of garage doors, enhancing their appeal for different homeowners.

In terms of longevity, the garage door openers are built with high-quality materials, promising durability and a longer lifespan. They also feature a noise-dampening design that minimizes operational sound, making them an excellent choice for residential applications.

Overall, the Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT garage door openers combine modern technology with user-friendly features to offer a secure, efficient, and convenient garage solution for today's smart homes. Their innovative approach addresses the traditional needs of homeowners while embracing new technological advancements, making them a relevant choice in today's market.
Top Page Image Contents