Sears 139.53960SRT, 139.53968SRT Install the Door Control, Llilllllliltltl Illliillllil

Page 18

INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet where small children cannot reach, away from moving parts of door and door hardware.

If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in

new home construction), it may be mounted to a single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of bell wire and connect to the two terminal screws on back of door

control by color: white to 2 and white/red to 1.

2.Door Control Button: Fasten securely with 6ABx1-l/2" screws.

Console Model: Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4"self-tapping screws (standard

installation) or 6-32x1" machine screws (into gang box) as follows:

•Install bottom screw, allowing 1//8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. 13onot overtighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Be careful not to pierce wire with a staple, creating a short or open circuit.

4.Connect the bell wire to the terminal screws on the motor unit panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

6.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

DO NOT connect power and operate opener at this time, The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

TopreventpossibleSERIOUSINJURYor DEATHfrom electrocution:

•Besurepoweris not connectedBEFOREinstallingdoor control.

•ConnectONLYto 24 VOLTlow voltagewires. TopreventpossibleSERIOUSINJURYor DEATHfroma closinggaragedoor:

•Installdoorcontrolwithinsightof garagedoor,out of reachof childrenat aminimumheightof 5feet,andaway fromall movingpartsof door.

•NEVERpermitchildrento operateor playwithdoorc0ntrol pushbuttonsor remotecontroltransmitters.

•ActivatedoorONLYwhenit canbeseenclearly,is properly adjusted,andthereareno obstructionsto doortravel.

ALWAYSkeepgaragedoor insight untilcompletelyclosed. NEVERpermitanyoneto crosspathof closinggaragedoor.

Outside Keylock Accessory Connections

To opener terminal screws: white to 2; white/red to 1

_] I_!ll_illlllliltltl Illliillllil_>

HARDWARE

SHOWN

 

ACTUAL

SIZE

6AB x 1-1/2"Screw

 

 

 

 

Door Control Button

 

 

 

H; IAI212Il1111/12,,tiSIcl'el/VJ_

_

nsulated

 

Control Console (std installation)

 

Staples

I 116!; I21IxII ,! ':Ictrle!; II

 

 

 

Control Console (pre-wired)

Dry

Wall Anchors

Figure 1

 

Figure 2

REMOVE & REPLACE

COVER

PRE-WtRED

TO Replace,

To Remove,

INSTALLATION

 

Insert Top

Twist

 

Tabs._. First.

Here

24 Volt

 

 

2-Conductor

 

 

Bell Wire in

 

 

Gang Box

Lighted

 

 

Push Button

 

 

 

 

 

:_F==_===_==

Top

 

 

 

_v

Mounting

 

 

 

 

- Hole

 

 

/

.

> Terminal

 

 

_

Sorews

Screws

Bell

 

 

Bottom

Wire

 

 

Terminal

Ben

 

Mounting

 

 

 

 

 

Wire

_

Hole

(BACK V_EW)

 

(BACK VIEW)

 

 

DOOR CONTROL BUTTON

 

PREMIUM

CONTROL CONSOLE

Back Panel

of Opener

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Garage Door Opener Abridor DE Puerta DE Cochera 4tI Warning Tools needed Preparing your garage doorSectional Door One-Piece Door Level DrillPlanning Sectional Door InstallationSectional Door Installations Closed PositionONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track Finished CeilingCarton Inventory Assembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Back RailsTo Motor Unit Install the Idler Pulley Hardware Shown Actual SizeOn TOP and Sides Bracket Sha Inside Dispensin9Master Link Cap SprocketII/2 Inch Tighten the ChainChain Base fRail Mid length of RailDetermine the Header Bracket Location Sectional Door ONE-PIECEDOOR with TrackProceed to , One-piece door without track jamb hardware ExampleProceed toStep One-piece door without track pivot hardwareWall Header Bracket Installation Ceiling Header Bracket InstallationAttach the Rail to the Header Bracket HoleTempora Suppo ONE-PIECEDOOR Without Track Position the OpenerSectional Door or ONE-PIECE Door with Track EngagedreleasedStrJctural HardwareshownactualsizeInstall the Door Control Outside Keylock Accessory ConnectionsLlilllllliltltl Illliillllil Attach the Emergency Release Rope and Handle Lens GuideOverhand Electrical Requirements Reinstall the coverPermanent Wiring Connection Ground Tab Green Ground ScrewFacing the door from inside the garage Install The Safety Reversing SensorImportant Information about Safety Reversing Sensor Above floorWall installation Installing the BracketsGarage door track installation preferred Floor installationTroubleshooting the Safety Sensors Mounting and Wiring the Safety Sensors FigureAligning the Safety Sensors Opener Terminal ScrewsFasten the Door Bracket Sectional DoorsBracket IIIIIIIIIIIIIIIIIIII!IIIIIII!IIIIIINut5,16HiiBo,tLkwa6r ONE-PIECE DoorsConnect Door Arm to Trolley Sectional Doors onlyAssemble the door arm, Figure Adjustment procedures, FigureClosed door adjustment decrease Down travel limit ALL ONE-PIECE DoorsAdjust the UP open force as explained in Adjustment Step Adjust the UP and Down Travel LimitsHOW and When to Adjust the Limits If door does not open at least 5 feetTest the Down close force Adjust the ForceHOW and When to Adjust the Forces Test the UP open forceImportant Safety Check Test the Safety Reversal SystemAdjust Test the Safety Reversing SensorImportant Safety Instructions Using Your Garage Door OpenerLock feature Using the Wall.Mounted Door ControlLight feature To Open the Door ManuallyCare Your Opener Twice a YearOnce a Year Having a Problem? Control Using the Learn ButtonTo Add an Additional Hand.held Remote To Erase All Codes From Motor Unit MemoryUsing the Learn Button To Add or Change a Keyless Entry PINKEY Part NO. NO.DESCRIPTION Rail Assembly PartsInstallation Parts KEY Part Description1817 Motor Unit Assembly PartsLimit Switch Not ShownAvailable only through Sears Parts & Service Sears WarrantyNbmeros Servicio Contra Tapa AccesoriosGarantia IntroduccionHerramientas Preparaci6n de la puerta de su cocheraPuerta seccional Puerta de una sola pieza NecesariasFesortede torsi n PlanificacienInstalacion CON UNA Puerta Seccional Control dl La puertaInstalacion CON Puertas DE UNA Sola Pieza Planificaci6n continbaPuerta DE UNA Sola Pieza SIN Carril Puerta DE UNA Pieza CON CarrilEntrada sin Ilave Inventario de las cajas53970,5393 Reversa de segurdadun ojo transmisorInventario de piezas TORNILLERiA Y Piezas Para LA InstalacionTORNILLERiA Y Piezas Para EL Armado Monte el riel e instale el trole LA PuertaSujete el riel al motor MONTAJE, PasoInstale la polea Ioca Estas Piezas SE Muestran /..= EN SU Tamaio NormalInstale la cadena o cable y coloque La cubierta de la polea Apriete la cadena ParaercaapretarinternaDetermine dnde va a instalar La mnsula del cabeza Puerta Seccional Puerta DE UNA Sola Pieza CON CarrilContinUe con el Paso 2, paglna Ejemplo Puerta de una pieza sin carril tornilleria del pivotePuerta DE UNA Sola Pieza SIN Carril SumeInstale la mnsula del cabezal Instalacion DE LA M#NSULA DEL Cabezal EN LA Pared DelanteraInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Coloque el riel en la mnsula del cabezal Con unEstas Piezas SE Muestran EN SU Tamaio Normal Coloque el abridor Puerta Seccional O Puerta DE UNA Sola Peza CON CarrilPJL Trole ixterno Trie interno INSTALACION,PASO Cuelgue el abridorFgura Instale la unidad de control Premium No apriete en excesoFlgura Instale la luce y lente Coloque la cuerda y la manija de emergenciaConexioncon Cableado Permanente INSTALACION, PasoRequisitos para la instalaci6n elctrica LangetaInstale el sensor del sistema de Reversa de seguridad Vista de la puerta desde el interior de la cocheraFstas Piezas SE Muestran EN SU Tamaio Normal CMO Alinear LOS Sensores DE Seguridad Montaje Y Cableado DE LOS Sensores DELSistema DE Reversa DE Seguridad Las terminales del abridor Cabe de campanaPuertas Seccionales Sujete la mnsula de la puertaUra Si su puerta es de metal, aluminioPuertas DE UNA Sola Pieza Cielo rasoDe pulgadaRoldana de 5/16 de pulgada Conecte el brazo de la puerta al trole Solo Para Puertas SeccionalesEstas Piezas SE Muestran EN SU Tamano Normal Conecte el brazo de la puerta al trole Arme el brazo de la puerta, FiguraProcedimiento de ajuste, Figura Posicion Completamente CerradaRecorrldo Ajuste el Iimite del recorrido haciaArriba y hacia abajo COMe Y Cuando Ajustar LOS LiMITESPruebe la fuerza del recorrido hacia abajo cerrar Ajuste la fuerzaComo Y Cuando Ajustar LA Fuerza DEL Abridor Pruebe la fuerza del recorrido hacia arriba abrirAJUSTES, Paso Pruebe el sensor del sistema de reversa de seguridadPruebe el sistema de reversa de seguridad Cno usar su abridor de puerta de cochera Active su abridor de alguna de las siguientes manerasC6mo usar la unidad de control de pared Cdmo abrir la puerta manualmenteSeguro Calendario DE Mantenimiento Mantenimiento De su abridor de puerta De cocheraLA Bateriadel Controlremoto Dos veces al aoSi tiene algbn problema El control remote tiene corto alcanceControles remotos de 3 funciones Cbmo agregar un control remoto manual adicionaJComo Usarel BOT3NAPRENDER Learn Todos los cSdigosPara poner o cambiar el PIN de la Entrada sin Ilaves Entrada sin Ilave de funciones mOltiples Pies se abra completarnenteControl remoto compacto de 3 funciones Mdnsulas de extensi6nWww, sears.com LE-FOYER

139.53960SRT, 139.53968SRT, 139.53971SRT specifications

Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT are a series of garage door openers that have gained recognition for their reliability and advanced features. These models represent a shift towards smarter technology in home automation, providing homeowners with increased convenience, security, and control over their garage doors.

One of the standout features of these models is their Smart Technology integration. Each unit is equipped with the ability to connect to Wi-Fi, allowing users to control their garage doors remotely through a smartphone app. This means that you can open or close your garage door from anywhere, check its status, and receive notifications if the door is left open for an extended period. This feature enhances home security by providing real-time updates, giving users peace of mind when they are away from home.

The 139.53971SRT model is designed with a powerful motor that ensures smooth and quiet operation, making it suitable for homes with bedrooms adjacent to the garage. It features a built-in battery backup system, which is crucial during power outages, providing peace of mind that your garage door can still be operated.

Meanwhile, the 139.53968SRT and 139.53960SRT models come with a range of safety features such as the security keypad and 3-button remote control, which allow multiple users to gain access without the need for a physical key. The Smart Technology also incorporates advanced encryption protocols that help prevent unauthorized access, ensuring the garage remains secure.

Additionally, all three models are designed for easy installation and come with a variety of installation accessories. Their adaptability makes them compatible with a wide range of garage doors, enhancing their appeal for different homeowners.

In terms of longevity, the garage door openers are built with high-quality materials, promising durability and a longer lifespan. They also feature a noise-dampening design that minimizes operational sound, making them an excellent choice for residential applications.

Overall, the Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT garage door openers combine modern technology with user-friendly features to offer a secure, efficient, and convenient garage solution for today's smart homes. Their innovative approach addresses the traditional needs of homeowners while embracing new technological advancements, making them a relevant choice in today's market.
Top Page Image Contents