Sears 139.53960SRT, 139.53968SRT Assemble the door arm, Figure, Adjustment procedures, Figure

Page 27

ALL ONE-PIECE DOORS

1.Assemble the door arm, Figure 4:

•Fasten the straight and curved door arm sections together to the tongest possible length (with a 2 or 3 hole overlap).

•With the door closed, connect the straight door arm section to the door bracket with the

5/16"xl -1/4" clevis pin.

•Secure with a ring fastener.

2.Adjustment procedures, Figure 5:

On one-piece doors, before connectingthe door arm to the trolley,the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 28. Follow , adjustment procedures below.

•Open door adjustment: decrease UP travel limit

-Turn the UP limit adjustment screw counter- clockwise 5 1/2 turns.

-Press the Door Control push button. The trolley will travel to the fully open position.

-Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer to the fully open trolley/door arm positions in the illustration. If the arm does not extend far enough, adjust the limit further. One full turn equals 2" of trolley travel.

•Closed door adjustment: decrease DOWN travel limit

-Turn the DOWN limit adjustment screw clockwise 5 complete turns.

I

FULLY CLOSED POSITION

 

Inner Trolley

Outer Trolley

Door Bracket

_

Ring

 

 

 

 

Fastener

 

 

 

 

 

Nuts

 

 

 

Lock

5/16"-16

 

 

 

5/16"

 

Clevis

Pin

Arm

 

 

 

 

 

Washers

 

rigi=_:-ur-

4

 

5/16"-18x7/8

Curved Door Arm

-Press the Door Control push button. The trolley will travel to the fully closed position.

-Manually close the door and lift the door arm to the trolley. The arm should touch the trolley just ahead of the door arm connector hole. Refer to

the fully closed trolley/door arm positions in the illustration. If the arm is behind the connector

hole, adjust the limit further. One full turn equals 2" of trolley travel.

3.Connect the door arm to the trolley:

•Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be necessary to lift the door slightly to make the connection.

•Secure with a ring fastener.

•Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor.

FULLY OPEN POSITION

Outer Trolley

Door Arm

Figure 5

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Garage Door Opener Abridor DE Puerta DE Cochera 4tI Warning Level Drill Preparing your garage doorSectional Door One-Piece Door Tools neededClosed Position Sectional Door InstallationSectional Door Installations PlanningFinished Ceiling ONE-PIECE Door InstallationsONE-PIECE Door Without Track ONE-PIECE Door with TrackCarton Inventory Assembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Back RailsTo Motor Unit Install the Idler Pulley Hardware Shown Actual SizeOn TOP and Sides Bracket Sprocket Inside Dispensin9Master Link Cap ShaBase fRail Mid length of Rail Tighten the ChainChain II/2 InchDetermine the Header Bracket Location Sectional Door ONE-PIECEDOOR with TrackProceed to , One-piece door without track pivot hardware ExampleProceed toStep One-piece door without track jamb hardwareCeiling Header Bracket Installation Wall Header Bracket InstallationAttach the Rail to the Header Bracket HoleTempora Suppo Engagedreleased Position the OpenerSectional Door or ONE-PIECE Door with Track ONE-PIECEDOOR Without TrackHardwareshownactualsize StrJcturalInstall the Door Control Outside Keylock Accessory ConnectionsLlilllllliltltl Illliillllil Attach the Emergency Release Rope and Handle Lens GuideOverhand Ground Tab Green Ground Screw Reinstall the coverPermanent Wiring Connection Electrical RequirementsAbove floor Install The Safety Reversing SensorImportant Information about Safety Reversing Sensor Facing the door from inside the garageFloor installation Installing the BracketsGarage door track installation preferred Wall installationOpener Terminal Screws Mounting and Wiring the Safety Sensors FigureAligning the Safety Sensors Troubleshooting the Safety SensorsFasten the Door Bracket Sectional DoorsBracket ONE-PIECE Doors IIIIIIIIIIIIIIIIIIII!IIIIIII!IIIIIINut5,16HiiBo,tLkwa6rSectional Doors only Connect Door Arm to TrolleyALL ONE-PIECE Doors Adjustment procedures, FigureClosed door adjustment decrease Down travel limit Assemble the door arm, FigureIf door does not open at least 5 feet Adjust the UP and Down Travel LimitsHOW and When to Adjust the Limits Adjust the UP open force as explained in Adjustment StepTest the UP open force Adjust the ForceHOW and When to Adjust the Forces Test the Down close forceTest the Safety Reversing Sensor Test the Safety Reversal SystemAdjust Important Safety CheckUsing Your Garage Door Opener Important Safety InstructionsTo Open the Door Manually Using the Wall.Mounted Door ControlLight feature Lock featureCare Your Opener Twice a YearOnce a Year Having a Problem? To Erase All Codes From Motor Unit Memory Using the Learn ButtonTo Add an Additional Hand.held Remote ControlTo Add or Change a Keyless Entry PIN Using the Learn ButtonKEY Part Description Rail Assembly PartsInstallation Parts KEY Part NO. NO.DESCRIPTIONNot Shown Motor Unit Assembly PartsLimit Switch 1817Sears Warranty Available only through Sears Parts & ServiceIntroduccion AccesoriosGarantia Nbmeros Servicio Contra TapaNecesarias Preparaci6n de la puerta de su cocheraPuerta seccional Puerta de una sola pieza HerramientasControl dl La puerta PlanificacienInstalacion CON UNA Puerta Seccional Fesortede torsi nPuerta DE UNA Pieza CON Carril Planificaci6n continbaPuerta DE UNA Sola Pieza SIN Carril Instalacion CON Puertas DE UNA Sola PiezaReversa de segurdadun ojo transmisor Inventario de las cajas53970,5393 Entrada sin IlaveInventario de piezas TORNILLERiA Y Piezas Para LA InstalacionTORNILLERiA Y Piezas Para EL Armado LA Puerta Monte el riel e instale el troleEstas Piezas SE Muestran /..= EN SU Tamaio Normal MONTAJE, PasoInstale la polea Ioca Sujete el riel al motorInstale la cadena o cable y coloque La cubierta de la polea Paraercaapretarinterna Apriete la cadenaDetermine dnde va a instalar La mnsula del cabeza Puerta Seccional Puerta DE UNA Sola Pieza CON CarrilContinUe con el Paso 2, paglna Sume Puerta de una pieza sin carril tornilleria del pivotePuerta DE UNA Sola Pieza SIN Carril EjemploInstale la mnsula del cabezal Instalacion DE LA M#NSULA DEL Cabezal EN LA Pared DelanteraInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Coloque el riel en la mnsula del cabezal Con unEstas Piezas SE Muestran EN SU Tamaio Normal Coloque el abridor Puerta Seccional O Puerta DE UNA Sola Peza CON CarrilPJL Trole ixterno Trie interno INSTALACION,PASO Cuelgue el abridorFgura Instale la unidad de control Premium No apriete en excesoFlgura Coloque la cuerda y la manija de emergencia Instale la luce y lenteLangeta INSTALACION, PasoRequisitos para la instalaci6n elctrica Conexioncon Cableado PermanenteVista de la puerta desde el interior de la cochera Instale el sensor del sistema de Reversa de seguridadFstas Piezas SE Muestran EN SU Tamaio Normal Las terminales del abridor Cabe de campana Montaje Y Cableado DE LOS Sensores DELSistema DE Reversa DE Seguridad CMO Alinear LOS Sensores DE SeguridadSi su puerta es de metal, aluminio Sujete la mnsula de la puertaUra Puertas SeccionalesPuertas DE UNA Sola Pieza Cielo rasoDe pulgadaRoldana de 5/16 de pulgada Conecte el brazo de la puerta al trole Solo Para Puertas SeccionalesEstas Piezas SE Muestran EN SU Tamano Normal Posicion Completamente Cerrada Arme el brazo de la puerta, FiguraProcedimiento de ajuste, Figura Conecte el brazo de la puerta al troleCOMe Y Cuando Ajustar LOS LiMITES Ajuste el Iimite del recorrido haciaArriba y hacia abajo RecorrldoPruebe la fuerza del recorrido hacia arriba abrir Ajuste la fuerzaComo Y Cuando Ajustar LA Fuerza DEL Abridor Pruebe la fuerza del recorrido hacia abajo cerrarAJUSTES, Paso Pruebe el sensor del sistema de reversa de seguridadPruebe el sistema de reversa de seguridad Active su abridor de alguna de las siguientes maneras Cno usar su abridor de puerta de cocheraC6mo usar la unidad de control de pared Cdmo abrir la puerta manualmenteSeguro Dos veces al ao Mantenimiento De su abridor de puerta De cocheraLA Bateriadel Controlremoto Calendario DE MantenimientoEl control remote tiene corto alcance Si tiene algbn problemaTodos los cSdigos Cbmo agregar un control remoto manual adicionaJComo Usarel BOT3NAPRENDER Learn Controles remotos de 3 funcionesPara poner o cambiar el PIN de la Entrada sin Ilaves Mdnsulas de extensi6n Pies se abra completarnenteControl remoto compacto de 3 funciones Entrada sin Ilave de funciones mOltiplesLE-FOYER Www, sears.com

139.53960SRT, 139.53968SRT, 139.53971SRT specifications

Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT are a series of garage door openers that have gained recognition for their reliability and advanced features. These models represent a shift towards smarter technology in home automation, providing homeowners with increased convenience, security, and control over their garage doors.

One of the standout features of these models is their Smart Technology integration. Each unit is equipped with the ability to connect to Wi-Fi, allowing users to control their garage doors remotely through a smartphone app. This means that you can open or close your garage door from anywhere, check its status, and receive notifications if the door is left open for an extended period. This feature enhances home security by providing real-time updates, giving users peace of mind when they are away from home.

The 139.53971SRT model is designed with a powerful motor that ensures smooth and quiet operation, making it suitable for homes with bedrooms adjacent to the garage. It features a built-in battery backup system, which is crucial during power outages, providing peace of mind that your garage door can still be operated.

Meanwhile, the 139.53968SRT and 139.53960SRT models come with a range of safety features such as the security keypad and 3-button remote control, which allow multiple users to gain access without the need for a physical key. The Smart Technology also incorporates advanced encryption protocols that help prevent unauthorized access, ensuring the garage remains secure.

Additionally, all three models are designed for easy installation and come with a variety of installation accessories. Their adaptability makes them compatible with a wide range of garage doors, enhancing their appeal for different homeowners.

In terms of longevity, the garage door openers are built with high-quality materials, promising durability and a longer lifespan. They also feature a noise-dampening design that minimizes operational sound, making them an excellent choice for residential applications.

Overall, the Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT garage door openers combine modern technology with user-friendly features to offer a secure, efficient, and convenient garage solution for today's smart homes. Their innovative approach addresses the traditional needs of homeowners while embracing new technological advancements, making them a relevant choice in today's market.
Top Page Image Contents