Sears 139.53971SRT, 139.53960SRT, 139.53968SRT owner manual StrJctural, Hardwareshownactualsize

Page 17

INSTALLATION STEP 5

Hang the Opener

Two representatLve installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are not provided. (See Accessories.)

1.Measure the distance from each side of the motor unit to the structural support.

2, Cut both pieces of the hanging bracket to required lengths.

3.Drill 3/16" pilot holes in the structural supports.

4.Attach one end of each bracket to a support with 5/16"-18xl-7/8" lag screws.

5.Fasten the opener to the hanging brackets with 5/16"-18x7/8" hex screws, lock washers and nuts.

6.Check to make sure the rail is centered over the door (or in line with the header bracket if the bracket is not centered above the door).

7.Remove the 2x4. Operate the door manually. If the door hits the rail, raise the header bracket.

NOTE: Do NOT connect power to opener at this time.

To avoid possibleSERIOUSINJURYfrom a falling garagedoor opener,fasten it SECURELYto structural supports of the garage.ConcreteanchorsMUSTbeused if installingany bracketsinto masonry.

Figure 1

Str'Jctural

Lag Screws 5/16"-18xl-7/8"

Measure \,

Distance ',

5/16"-!8×718"Screw 5/16" Lock Washer 5/16"-18 Nut

Figure 2

Hidden..-

 

.-_

5/16"-18xl-718"

_.-

 

 

Bracket

 

--_

(NotProvided)

 

(Not Provided)_-

_ . .- :::..-"_'_ _._._J

_

5/16"-18x7/e" Screw

 

"'_

 

 

5/16" Lock Washer

 

"--

 

 

5/16"-18 Nut

 

5/16"-18x718"$crew

 

 

 

HARDWARESHOWNACTUALSIZE

 

 

 

 

Ll,l llLlllltI,LIlllll.

5/165/16"LockWasher18_i_,

 

.TI::]_ !_;'_'

 

 

 

 

Lag Screw 5116"-18x1-7/8"

5/16"- 18x7/8"

Nut 5/16"-18

Lock Washer 5/16"

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Garage Door Opener Abridor DE Puerta DE Cochera 4tI Warning Sectional Door One-Piece Door Preparing your garage doorTools needed Level DrillSectional Door Installations Sectional Door InstallationPlanning Closed PositionONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track Finished CeilingCarton Inventory Hardware Inventory Assembly HardwareInstallation Hardware To Motor Unit Assemble the Rail & Install the TrolleyBack Rails On TOP and Sides Bracket Install the Idler PulleyHardware Shown Actual Size Master Link Cap Inside Dispensin9Sha SprocketChain Tighten the ChainII/2 Inch Base fRail Mid length of RailProceed to , Determine the Header Bracket LocationSectional Door ONE-PIECEDOOR with Track Proceed toStep ExampleOne-piece door without track jamb hardware One-piece door without track pivot hardwareCeiling Header Bracket Installation Wall Header Bracket InstallationTempora Suppo Attach the Rail to the Header BracketHole Sectional Door or ONE-PIECE Door with Track Position the OpenerONE-PIECEDOOR Without Track EngagedreleasedHardwareshownactualsize StrJcturalLlilllllliltltl Illliillllil Install the Door ControlOutside Keylock Accessory Connections Overhand Attach the Emergency Release Rope and HandleLens Guide Permanent Wiring Connection Reinstall the coverElectrical Requirements Ground Tab Green Ground ScrewImportant Information about Safety Reversing Sensor Install The Safety Reversing SensorFacing the door from inside the garage Above floorGarage door track installation preferred Installing the BracketsWall installation Floor installationAligning the Safety Sensors Mounting and Wiring the Safety Sensors FigureTroubleshooting the Safety Sensors Opener Terminal ScrewsBracket Fasten the Door BracketSectional Doors ONE-PIECE Doors IIIIIIIIIIIIIIIIIIII!IIIIIII!IIIIIINut5,16HiiBo,tLkwa6rSectional Doors only Connect Door Arm to TrolleyClosed door adjustment decrease Down travel limit Adjustment procedures, FigureAssemble the door arm, Figure ALL ONE-PIECE DoorsHOW and When to Adjust the Limits Adjust the UP and Down Travel LimitsAdjust the UP open force as explained in Adjustment Step If door does not open at least 5 feetHOW and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceAdjust Test the Safety Reversal SystemImportant Safety Check Test the Safety Reversing SensorUsing Your Garage Door Opener Important Safety InstructionsLight feature Using the Wall.Mounted Door ControlLock feature To Open the Door ManuallyOnce a Year Care Your OpenerTwice a Year Having a Problem? To Add an Additional Hand.held Remote Using the Learn ButtonControl To Erase All Codes From Motor Unit MemoryTo Add or Change a Keyless Entry PIN Using the Learn ButtonInstallation Parts Rail Assembly PartsKEY Part NO. NO.DESCRIPTION KEY Part DescriptionLimit Switch Motor Unit Assembly Parts1817 Not ShownSears Warranty Available only through Sears Parts & ServiceGarantia AccesoriosNbmeros Servicio Contra Tapa IntroduccionPuerta seccional Puerta de una sola pieza Preparaci6n de la puerta de su cocheraHerramientas NecesariasInstalacion CON UNA Puerta Seccional PlanificacienFesortede torsi n Control dl La puertaPuerta DE UNA Sola Pieza SIN Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Pieza CON Carril53970,5393 Inventario de las cajasEntrada sin Ilave Reversa de segurdadun ojo transmisorTORNILLERiA Y Piezas Para EL Armado Inventario de piezasTORNILLERiA Y Piezas Para LA Instalacion LA Puerta Monte el riel e instale el troleInstale la polea Ioca MONTAJE, PasoSujete el riel al motor Estas Piezas SE Muestran /..= EN SU Tamaio NormalInstale la cadena o cable y coloque La cubierta de la polea Paraercaapretarinterna Apriete la cadenaContinUe con el Paso 2, paglna Determine dnde va a instalar La mnsula del cabezaPuerta Seccional Puerta DE UNA Sola Pieza CON Carril Puerta DE UNA Sola Pieza SIN Carril Puerta de una pieza sin carril tornilleria del pivoteEjemplo SumeInstalacion DE LA Mensula DEL Cabezal EN EL Cielo Raso Instale la mnsula del cabezalInstalacion DE LA M#NSULA DEL Cabezal EN LA Pared Delantera Estas Piezas SE Muestran EN SU Tamaio Normal Coloque el riel en la mnsula del cabezalCon un PJL Trole ixterno Trie interno Coloque el abridorPuerta Seccional O Puerta DE UNA Sola Peza CON Carril Fgura INSTALACION,PASOCuelgue el abridor Flgura Instale la unidad de control PremiumNo apriete en exceso Coloque la cuerda y la manija de emergencia Instale la luce y lenteRequisitos para la instalaci6n elctrica INSTALACION, PasoConexioncon Cableado Permanente LangetaVista de la puerta desde el interior de la cochera Instale el sensor del sistema de Reversa de seguridadFstas Piezas SE Muestran EN SU Tamaio Normal Sistema DE Reversa DE Seguridad Montaje Y Cableado DE LOS Sensores DELCMO Alinear LOS Sensores DE Seguridad Las terminales del abridor Cabe de campanaUra Sujete la mnsula de la puertaPuertas Seccionales Si su puerta es de metal, aluminioDe pulgadaRoldana de 5/16 de pulgada Puertas DE UNA Sola PiezaCielo raso Estas Piezas SE Muestran EN SU Tamano Normal Conecte el brazo de la puerta al troleSolo Para Puertas Seccionales Procedimiento de ajuste, Figura Arme el brazo de la puerta, FiguraConecte el brazo de la puerta al trole Posicion Completamente CerradaArriba y hacia abajo Ajuste el Iimite del recorrido haciaRecorrldo COMe Y Cuando Ajustar LOS LiMITESComo Y Cuando Ajustar LA Fuerza DEL Abridor Ajuste la fuerzaPruebe la fuerza del recorrido hacia abajo cerrar Pruebe la fuerza del recorrido hacia arriba abrirPruebe el sistema de reversa de seguridad AJUSTES, PasoPruebe el sensor del sistema de reversa de seguridad Active su abridor de alguna de las siguientes maneras Cno usar su abridor de puerta de cocheraSeguro C6mo usar la unidad de control de paredCdmo abrir la puerta manualmente LA Bateriadel Controlremoto Mantenimiento De su abridor de puerta De cocheraCalendario DE Mantenimiento Dos veces al aoEl control remote tiene corto alcance Si tiene algbn problemaComo Usarel BOT3NAPRENDER Learn Cbmo agregar un control remoto manual adicionaJControles remotos de 3 funciones Todos los cSdigosPara poner o cambiar el PIN de la Entrada sin Ilaves Control remoto compacto de 3 funciones Pies se abra completarnenteEntrada sin Ilave de funciones mOltiples Mdnsulas de extensi6nLE-FOYER Www, sears.com

139.53960SRT, 139.53968SRT, 139.53971SRT specifications

Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT are a series of garage door openers that have gained recognition for their reliability and advanced features. These models represent a shift towards smarter technology in home automation, providing homeowners with increased convenience, security, and control over their garage doors.

One of the standout features of these models is their Smart Technology integration. Each unit is equipped with the ability to connect to Wi-Fi, allowing users to control their garage doors remotely through a smartphone app. This means that you can open or close your garage door from anywhere, check its status, and receive notifications if the door is left open for an extended period. This feature enhances home security by providing real-time updates, giving users peace of mind when they are away from home.

The 139.53971SRT model is designed with a powerful motor that ensures smooth and quiet operation, making it suitable for homes with bedrooms adjacent to the garage. It features a built-in battery backup system, which is crucial during power outages, providing peace of mind that your garage door can still be operated.

Meanwhile, the 139.53968SRT and 139.53960SRT models come with a range of safety features such as the security keypad and 3-button remote control, which allow multiple users to gain access without the need for a physical key. The Smart Technology also incorporates advanced encryption protocols that help prevent unauthorized access, ensuring the garage remains secure.

Additionally, all three models are designed for easy installation and come with a variety of installation accessories. Their adaptability makes them compatible with a wide range of garage doors, enhancing their appeal for different homeowners.

In terms of longevity, the garage door openers are built with high-quality materials, promising durability and a longer lifespan. They also feature a noise-dampening design that minimizes operational sound, making them an excellent choice for residential applications.

Overall, the Sears 139.53971SRT, 139.53968SRT, and 139.53960SRT garage door openers combine modern technology with user-friendly features to offer a secure, efficient, and convenient garage solution for today's smart homes. Their innovative approach addresses the traditional needs of homeowners while embracing new technological advancements, making them a relevant choice in today's market.
Top Page Image Contents