Harman Stove Company P61A manual Stocked at depot, #2 Pre Serial number 008085092 Feeder Assembly

Page 36

Service Parts

P61A Pellet

 

 

 

beginning Manufacturing date: n/A

 

ending Manufacturing date: Active

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

iteM

description

cOMMentS

PARt nuMbeR

Stocked at depot

 

 

Pre 008085803

1-10-08622

Y

1

Hopper Assembly

008085803

1-10-06819A

 

Thru 008087704

1-00-232108

 

 

 

Order both parts

 

 

 

Post 008087704

1-10-09685A

 

 

Hopper Switch 48”

Post 008087704

3-20-232108

Y

#2 Pre Serial number 008085092 Feeder Assembly

 

 

 

2.3

2.2

 

 

 

 

 

2.1

 

 

2.4

 

 

 

 

2.5

 

 

 

2.6

2.12

2.11 2.7

 

 

2.8

 

 

 

 

2.9

 

 

 

 

2.10

 

 

2

Feeder Assembly

Pre 008085803

1-10-09674A

 

2.1

Air Intake Damper Assembly

 

1-10-06466W

 

2.2

Air Intake Weldment

 

1-10-06461

 

2.3

Feeder Weldment

 

1-10-677150

Y

2.4

Slide Plate Assembly

 

1-10-08037

Y

2.5

Pusher Arm Assembly

 

1-10-06691

Y

2.6

Feed Cover and Gasket

2 Sets

1-00-677152

Y

2.7

Auger Assembly

 

3-50-00465

Y

2.8

Cam Bearing

 

3-31-3014

Y

2.9

Bearing Flange w/Hardware

 

1-00-04035

Y

2.10

Bracket, Gear Motor

 

1-00-01534

Y

2.11

Gear Motor, 4 RPM

 

3-20-60906

Y

2.12

Cast Cam Block

 

3-00-00153

Y

 

Feeder Repair kIt

 

1-10-677150

Y

 

Gasket, Feeder, Air Intake

Pkg of 6

3-44-72224-6

Y

Additional service parts on following page.

Image 36
Contents Installation & Operating Manual Safety NoticePage Label Table of Contents Important Notes Assembly and Installation Room Sensor InstallationInstallation InstallingMobile Home Installation With outside air installed, 6 feet VentingAddition, the following must be observed Negative Pressure, Shut-down, and Power Failure PL Vent, Must Be UsedOutside Air VentingVent Configurations #1 Preferred method #2 Preferred method#4 Installing into an existing chimney #5 Installing into an existingFireplace chimney #6 Installing into an existing fireplace chimney #7 Installing into an existing chimneyMinimum flue vent configuration #8 Installing through the ceilingStatus light error messages Automatic Ignition ESP ControlRoom Temperature Mode Automatic IGNITION/OPERATIONStove Temperature Mode Feed Adjuster KnobShut Down Procedure Igniter Switch to Auto up position Turn Mode Selector to OFFTurn Feed Adjuster to #4.4 Automatic Start UPManual IGNITION/Operation Igniter Switch to Manual down position Manual Start UPFill hopper with pellets and remove ashes as required.1 Low Draft Voltage Adjustment Low Draft Voltage AdjustmentMaintenance Glass ReplacementMinimizing Creosote Cleaning Scraping the burn potRemoving Ashes Not equipped with a fine dust filter may clog Disperse fly ash and soot into the roomSoot and Fly Ash Maintenance Burn Pot Burn Pot Cleaning and MaintenanceMaintenance Cleaning the Feeder Body Safety FeaturesTrouble-Shooting Cleaning Burn PotFire has Gone OUT- Check for status light Curing PaintFuel Specifications Fuel and Fuel StorageOperation in Stove Temp mode Operation in Room Temp modeChanges to Maintenance Schedule 30 P61A Pellet Stove Side Heat Shields Hopper Extension -Part#1-00-08636Direct Vent Wall Passthrough Kit Decorative Slate OptionsWiring Diagram SpecificationsLimited Lifetime Warranty Hearth & Home Technologies IncWarranty Conditions This warranty is void ifService Parts Part number list on following#2 Pre Serial number 008085092 Feeder Assembly Stocked at depot#3 Post Serial number 008085803 Feeder Assembly At depotStocked Clean Out Cover Sets 00-06623 P61A Pellet Service & Maintenance Log P61A Pellet Stove 42 P61A Pellet Stove Page Proudly Printed On 100% Recycled Paper