Rheem HE80-160N Failure to Operate, Fuel Conversions, Corrosive Atmospheres, Condensate

Page 13

FAILURE TO OPERATE

Should the burner fail to light, the control will perform two more ignition trials prior to entering a lockout state (flash- ing “LOC”). Note that each subsequent ignition trial will not occur immediately. After a failed ignition trial, the blower must run for approximately 10 seconds to purge the system, then the ignitor element must complete a 30 second warm-up period. Therefore, a time period of approximately 40 to 90 seconds will expire between each ignition trial. If the burner lights during any one of these three ignition trials, normal operation will resume. If the burner lights, but goes off in about 4 seconds, check the polarity of the wiring. See electrical on page 6. If the burner does not light after the third ignition trial, the control will enter a lockout state. This lockout state indicates that a problem exists with either the appli- ance, the controls, or the gas supply. Under such cir- cumstances, a qualified service technician should be contacted immediately to properly service the appliance and correct the problem. If a technician is not available, depressing the red button once will remove the lockout state so additional trials for ignition can be performed.

Any time flashing double zero’s are shown, you must look for an LED out, or flashing. The LED that is out or flashing will assist you in diagnosing lock out con- dition.

FUEL CONVERSIONS

This product may be converted from L.P. gas (propane) to Natural gas or from Natural gas to L.P. gas (propane). For information and requirements about this procedure call the Technical Service Department at 1-800-432- 8373.

!WARNING

Should overheating occur or the gas supply fail to shut off, turn off the manual gas control valve to the appliance.

!WARNING

DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace the water heater if the control system or any gas control which has been under water.

CORROSIVE ATMOSPHERES

The heater should not be installed near an air supply con- taining halogenated hydrocarbons. For example, the air in beauty salons, dry cleaning establishments, photo pro- cessing labs, and storage areas for liquid and powdered bleaches or swimming pool chemicals often contain hydrocarbons. The air there may be safe to breathe, but when it passes through a gas flame, corrosive elements are released that will shorten the life of any gas burning appliance. Propellants from common spray cans or gas leaks from refrigeration equipment are highly corrosive after passing through a flame. The limited warranty is voided when failure of water heater is due to a corrosive atmosphere. (Reference is made to the limited warranty for complete terms and conditions.)

CONDENSATE

This is a condensing high efficiency appliance, therefore this unit has a condensate removal system. Condensate is nothing more than water vapor, derived from the com- bustion products, similar to an automobile when it is ini- tially started. This condensate does have a low pH and should be treated with a condensate filter. This filter con- tains either lime crystals or marble crystals, which will neutralize the condensate. The outlet of the filter is sized for 5/8" ID (inside diameter) plastic tubing. It is very important that the condensate line is sloped away from and down to a suitable inside drain. If the condensate outlet on the AdvantagePlus is lower than the drain, you must use a condensate removal pump. It is also very important that the condensate line is not exposed to freezing temperatures, or any other type of blockage. Plastic tubing should be the only material used for the condensate line. Steel, brass, copper, or other metals will be subject to corrosion and deterioration. A second vent may be necessary to prevent condensate line vacuum lock if a long horizontal run is used. Also an increase to 1" tubing may be necessary.

NOTE: Always check local codes for proper evacuation of condensate.

INSTALLATION OF A CONDENSATE NEUTRALIZER AND PUMP (Not Supplied)

CONDENSATE LINE

CONDENSATE LINE WITH PUMP

FROM ADVANTAGE PLUS

FROM ADVANTAGE PLUS

TO DRAIN

TO DRAIN

CONDENSATE LINE MUST BE PITCHED AT LEAST 1/4" PER FOOT TO PROPERLY DRAIN. IF THIS CANNOT BE DONE OR A VERY LONG LENGTH OF CONDENSATE HOSE IS USED YOU MUST INCREASE THE CONDENSATE HOSE TO A MINIMUM OF 1" I.D. AND PLACE A TEE IN THE LINE AFTER THE CONDENSATE NEUTRALIZER TO PROPERLY REDUCE VACUUM LOCK IN THE DRAIN LINE.

CONTACT YOUR LOCAL WHOLESALE PLUMBING SUPPLY STORE FOR MORE INFORMATION ON CONDENSATE NEUTRALIZERS AND PUMPS

13

Image 13
Contents USE & Care Manual With Installation Instructions for the ContractorSpecifications If LP GAS is Present or Suspected Liquefied Petroleum ModelsN G E R Temperature and Pressure Relief Valve Local Installation RegulationsLocation Expansion TankDomestic Water Connections Special Instructions for Booster InstallationsGAS Connection Electrical ConnectionPipe / Fittings When Using 3 Vent Pipe Venting When Using 3 Vent PipeFor Longer Vent Lengths When Using 3 Vent Pipe Pipe / Fittings When Using 2 Vent Pipe Special Venting Instructions Using 2 Vent PipeFor Longer Vent Lengths When Using 2 Vent Pipe Cleaner / CementFriction Loss Equivalence Tables Temperature SET Point Adjustment Procedure Start UP ProcedureControl Description Never Purge from the T&P ValveStatus Indicators Thermostat Differential Adjustment ProcedureMaintenance Internal WiringFuel Conversions Failure to OperateCorrosive Atmospheres CondensateComponents of the AdvantagePlus Replacement Parts not ShownT E S GAS Valve AdjustmentIf There WAS no Ignition If Ignition WAS PoorStatus Indications Under Normal Conditions Status Indications Under Normal Operating Conditions Ignitor Lockout No Incoming Line Voltage or 24 VoltPossible Cause Remedy Ignition Lockout ECO Switch OpenPossible Cause Control Health Temperature Probe FaultCombustion AIR Blockage Page Integrated Water Heater Control Very Important SET-UP Instructions Venting Samples AdvantagePlus with Storage Tank Sequence of Operations Water is heating Verify flame presence through sight window Green LED on Main Trouble Shooting Guide Most Common Advantageplus Installation Concerns