Bradford-White Corp EF Section VII GAS Connections, Initial Preparation, Selection of Materials

Page 35

INITIAL PREPARATION

1.Make sure the solvent cement you are planning to use is designed for the specific application you are attempting.

2.Know the physical and chemical characteristics and limitations of the PVC, PVC cellular core, ABS or CPVC piping materials that you are about to use.

3.Know the reputation of your pipe and cement manufacturer and their products.

4.Know your own qualifications or those of your contractor. The solvent welding technique of joining PVC, PVC cellular core, ABS or CPVC pipe is a specialized skill just as any other pipe fitting technique.

5.Closely supervise the installation and inspect the finished job before start-up.

6.Contact the manufacturer, supplier, or competent consulting agency if you have any questions about the application or installation of PVC, PVC cellular core, ABS or CPVC pipe.

7.Take the time and effort to do a professional job. Shortcuts will only cause you problems and delays in start-up. The majority of failures in these systems are the result of shortcuts and/or improper joining techniques.

SELECTION OF MATERIALS

PRIMER – It is recommended that Tetrahydrofuran (THF) be used to prepare the surfaces of pipe and fittings for solvent welding. Do not use water, rags, gasoline or any other substitutes for cleaning PVC cellular core, ABS or CPVC surfaces. A chemical cleaner such as MEK may be used.

CEMENT – The cement should be a bodied cement of approximately 500 to 1600 centipoises viscosity containing 10-20% (by weight) virgin PVC material solvated with tetrahydrofuran (THF). Small quantities of dimethylformamide (DMF) may be included to act as a retarding agent to extend curing time. Select the proper cement; Schedule 40 cement should be used for Schedule 40 pipe. Never use all-purpose cements, commercial glues and adhesives or ABS cement to join PVC or CPVC pipe and fittings.

SAFETY PRECAUTION: PRIMERS AND CEMENTS ARE EXTREMELY FLAMMABLE AND MUST NOT BE STORED OR USED NEAR HEAT OR OPEN FLAME. ALSO, USE ONLY IN A WELL VENTILATED AREA.

SECTION VII: GAS CONNECTIONS

WARNING

Connect this water heater only to the type of gas as shown on the rating plate. Use clean black iron pipe or equivalent material approved by local codes and ordinances. (Dirt and scale from the pipe can enter the gas valve and cause it to malfunction). The inlet gas line must have at least a 3 inch (7.62 cm) drip leg (sediment trap) installed as close to the water heater’s gas valve as possible. A ground joint union must be installed in the gas supply line, as close to the water heater as possible, to permit servicing of the water heater. Compounds used on the threaded joints of the gas piping must be resistant to the action of liquefied petroleum gases/propane gas. DO NOT apply pipe dope to the gas valve inlet and make certain that no pipe dope has become lodged in the inlet screen of the gas valve. Extreme care must be taken to ensure no pipe dope enters the gas valve and to avoid excessive torque when tightening the gas supply line to the gas valve. Excessive torque may result in cracking of the gas valve housing. The suggested maximum torque is 31.5 foot lbs. (4.4 kg-m). The manufacturer of this water heater will not be liable for any damage or injury caused as a result of a cracked gas inlet as a result of excessive torque.

This water heater and its gas connection must be leak tested before placing the water heater in operation. Check for gas leaks with a soap and water solution and a brush or a commercial leak detector fluid.

NEVER USE A MATCH OR OPEN FLAME FOR TESTING!

The water heater is not intended for operation at higher than 14 inches (3483.8 Pa) water column (½ psi (3.5 kPa)) supply gas pressure. Higher gas supply pressures require supplemental reducing service regulation. Exposure to higher gas supply pressure may cause damage to the gas controls, which could result in fire or explosion. If overpressure has occurred such as through improper testing of gas lines or emergency malfunction of the supply system, the gas valve must be checked for safe operation. Make sure that the outside vents on the supply regulators and the safety vent valves are protected against blockage. These are parts of the gas supply system, not the water heater.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents What to do if YOU Smell GAS With Troubleshooting GuideTable of Contents Page Do not Operate the Appliance Until the Leakage is Corrected If YOU Smell GASDimensions Inches Section II SpecificationsSection III General Information FeaturesTemperature and Pressure Relief Valve Condensate Elbow With Trap Dishwashing Machine RequirementsSection IV Installation Instructions Minimum Clearance To Combustible Material UnpackingRemove Crate Recommended Minimum Clearances For Service AccessUnconfined Space LocationAIR Requirements Mechanical Exhausting of Room AIRChemical Vapor Corrosion Typical Installation IllustrationTypical Two Water Heater Connection Scalding Section V Water ConnectionsInstructions for Connections Alternate Space Heating Water Connections Approximate TIME/TEMPERATURE Relationships in ScaldsSection VI Venting Approved Venting Materials Venting Direct Vent InstallationCanadian US Installations2 Installations1 Clearance above Direct Vent Terminal Clearances Page Typical Horizontal Direct Vent System Typical Vertical Direct Vent System Installation Determining required vent length Power Vent InstallationPage Typical Horizontal Power Vent System Typical Vertical Power Vent System Installation Power Vent Maximum Vent Length Multiple INTAKE/EXHAUST Terminal Separation Distances Dimensional Layout of Concentric Vent Kit Concentric Vent Terminal Installation ProcedureRain Cap to Small Vent Pipe Ass’y Concentric Vent Side Wall Attachment Vent Pipe Preparation ModelsSelection of Materials Section VII GAS ConnectionsInitial Preparation GAS Pressure Regulation GAS Meter Size Natural Gases onlySection Viii Electrical Connections Wiring Diagram and SchematicSequence of Operation Section IX Operating InstructionsGeneral Instructions To Fill the Water HeaterLighting Instructions Temperature AdjustmentSight Glass Location Burner Flame CheckFlushing Water Heater Section X MaintenanceMaintenance Schedule GeneralSediment and Lime Scale Removal Draining Water HeaterFilling Water Heater To inspect or replace an anode Anode Inspection and ReplacementVent and AIR Intake System Drain Valve and Tank Access PanelCombustion System Inspection Section XI Troubleshooting GuideEF Series Water Heater Section XII Parts ListCombustion Surround Assy Ignition Control Assy

EF specifications

Bradford-White Corporation, a leader in water heating technology, has long been recognized for its innovation and quality in the industry. One of its standout offerings is the EF series, a line of high-efficiency water heaters designed to meet the growing demand for energy efficiency and reliable performance in residential and commercial applications.

The Bradford-White EF (Energy Factor) series features advanced, state-of-the-art technologies that optimize energy use while providing consistent hot water availability. One of the most notable aspects of these systems is their impressive energy efficiency ratings. The EF series utilizes cutting-edge insulation materials and advanced combustion technology, helping to minimize heat loss and reduce energy consumption. Customers benefit not only from lower utility bills but also from a product that is environmentally friendly.

Key features of the EF series include a patented Hydrojet Total Performance System, which enhances efficiency by reducing sediment buildup within the tank. This system contributes to a longer lifespan and optimal performance of the water heater, ensuring users have reliable hot water even during peak demand periods. Additionally, the EF series incorporates an intelligent electronic control system that monitors and adjusts the operation of the unit, further maximizing efficiency and providing precise temperature control.

Safety is another major consideration in the design of the EF series. Bradford-White has integrated advanced safety features, including a flame arrestor and a robust pressure relief valve, which ensure that the units operate safely and adhere to the highest industry standards. This commitment to safety demonstrates Bradford-White’s focus on providing peace of mind to homeowners and business owners alike.

Ease of installation and maintenance is a significant advantage of the EF series. Its compact design allows for flexible installation options, making it suitable for a variety of spaces, including tight or hard-to-reach areas. Moreover, the EF model is designed for simplified maintenance, which helps reduce labor costs and downtime for both homeowners and professionals.

Overall, the Bradford-White EF series is an excellent choice for those seeking a reliable, efficient, and safe water heating solution. With a blend of innovative technology, energy efficiency, and user-friendly features, the EF series exemplifies Bradford-White’s commitment to quality and customer satisfaction, making it a trusted name in the water heating industry.
Top Page Image Contents