Bradford-White Corp EF operation manual Typical Vertical Direct Vent System Installation

Page 24

Figure 14. Typical Vertical Direct Vent System Installation

(Note: Intake and exhaust terminals may be on different outside walls.)

Through The Wall Venting With Low Ground Clearance:

When venting cannot exit through the wall at a height greater than or equal to 12 inches (30.5 cm) (and above expected snow level) from the ground, then the installation must be modified as shown below (see Figure 15).

Figure 15. Vent Terminal (Low Ground Clearance)

24

Image 24
Contents With Troubleshooting Guide What to do if YOU Smell GASTable of Contents Page If YOU Smell GAS Do not Operate the Appliance Until the Leakage is CorrectedSection II Specifications Dimensions InchesFeatures Section III General InformationTemperature and Pressure Relief Valve Dishwashing Machine Requirements Condensate Elbow With TrapSection IV Installation Instructions Unpacking Minimum Clearance To Combustible MaterialRecommended Minimum Clearances For Service Access Remove CrateLocation AIR RequirementsMechanical Exhausting of Room AIR Unconfined SpaceTypical Installation Illustration Chemical Vapor CorrosionTypical Two Water Heater Connection Section V Water Connections Instructions for ConnectionsScalding Approximate TIME/TEMPERATURE Relationships in Scalds Alternate Space Heating Water ConnectionsSection VI Venting Approved Venting Materials Direct Vent Installation VentingCanadian US Installations2 Installations1 Clearance above Direct Vent Terminal Clearances Page Typical Horizontal Direct Vent System Typical Vertical Direct Vent System Installation Power Vent Installation Determining required vent lengthPage Typical Horizontal Power Vent System Typical Vertical Power Vent System Installation Power Vent Maximum Vent Length Multiple INTAKE/EXHAUST Terminal Separation Distances Concentric Vent Terminal Installation Procedure Dimensional Layout of Concentric Vent KitRain Cap to Small Vent Pipe Ass’y Concentric Vent Side Wall Attachment Models Vent Pipe PreparationSection VII GAS Connections Initial PreparationSelection of Materials GAS Meter Size Natural Gases only GAS Pressure RegulationWiring Diagram and Schematic Section Viii Electrical ConnectionsSection IX Operating Instructions General InstructionsTo Fill the Water Heater Sequence of OperationTemperature Adjustment Lighting InstructionsBurner Flame Check Sight Glass LocationSection X Maintenance Maintenance ScheduleGeneral Flushing Water HeaterDraining Water Heater Filling Water HeaterSediment and Lime Scale Removal Anode Inspection and Replacement To inspect or replace an anodeDrain Valve and Tank Access Panel Vent and AIR Intake SystemSection XI Troubleshooting Guide Combustion System InspectionSection XII Parts List EF Series Water HeaterCombustion Surround Assy Ignition Control Assy

EF specifications

Bradford-White Corporation, a leader in water heating technology, has long been recognized for its innovation and quality in the industry. One of its standout offerings is the EF series, a line of high-efficiency water heaters designed to meet the growing demand for energy efficiency and reliable performance in residential and commercial applications.

The Bradford-White EF (Energy Factor) series features advanced, state-of-the-art technologies that optimize energy use while providing consistent hot water availability. One of the most notable aspects of these systems is their impressive energy efficiency ratings. The EF series utilizes cutting-edge insulation materials and advanced combustion technology, helping to minimize heat loss and reduce energy consumption. Customers benefit not only from lower utility bills but also from a product that is environmentally friendly.

Key features of the EF series include a patented Hydrojet Total Performance System, which enhances efficiency by reducing sediment buildup within the tank. This system contributes to a longer lifespan and optimal performance of the water heater, ensuring users have reliable hot water even during peak demand periods. Additionally, the EF series incorporates an intelligent electronic control system that monitors and adjusts the operation of the unit, further maximizing efficiency and providing precise temperature control.

Safety is another major consideration in the design of the EF series. Bradford-White has integrated advanced safety features, including a flame arrestor and a robust pressure relief valve, which ensure that the units operate safely and adhere to the highest industry standards. This commitment to safety demonstrates Bradford-White’s focus on providing peace of mind to homeowners and business owners alike.

Ease of installation and maintenance is a significant advantage of the EF series. Its compact design allows for flexible installation options, making it suitable for a variety of spaces, including tight or hard-to-reach areas. Moreover, the EF model is designed for simplified maintenance, which helps reduce labor costs and downtime for both homeowners and professionals.

Overall, the Bradford-White EF series is an excellent choice for those seeking a reliable, efficient, and safe water heating solution. With a blend of innovative technology, energy efficiency, and user-friendly features, the EF series exemplifies Bradford-White’s commitment to quality and customer satisfaction, making it a trusted name in the water heating industry.