American Water Heater COMMERCIAL ELECTRIC WATER HEATERS Economy Mode Settings Time Clock Settings

Page 59

Economy Mode Settings

ELECTRONIC CONTROL SYSTEM

Economy Mode Settings

Time Clock Settings

ACTION

DISPLAY

From the Desktop Screen navigate to the Economy Mode Setup menu - see page 56 for instructions.

Use the Up/Down buttons to select (highlight in black) Current Time sub menu. Press the Operational Button underneath “CHANGE” to enter the Current Time sub menu.

Use the Up/Down buttons to select the “Weekday” setting.

Press the Operational Button underneath “CHANGE” to activate the adjustment mode for this setting.

Press the Up and Down buttons to adjust the Weekday setting to the current day.

Notice how the text above the Operational Buttons on the display changes to “ACCEPT” & “CANCEL” when the adjustment mode is activated and how the current setting is outlined rather than highlighted in black.

Press the Operational Button underneath “ACCEPT” to enter and confirm the new setting. Pressing the Operational Button underneath “CANCEL” would discard the new setting and retain the previous setting.

Use the Up/Down and the CHANGE/ACCEPT Operational Buttons to individually select and change the remaining time settings (Hour, Minutes, AM/PM) to the current time in the same way as outlined above.

When finished making changes press the Operational Button underneath “BACK” to confirm all new settings and update the control system. The display will automatically return to the Economy Mode Setup menu.

The new settings should be displayed as the Current

Time.

Servicing should only be performed by a Qualified Service Agent

57

Image 59

Contents Technical Support and Parts Service HandbookCOMMERCIAL ELECTRIC WATER HEATERS MODELS STCE3-52/80/119 & ITCE3-52/80/119Page COMMERCIAL ELECTRIC WATER HEATER TABLE OF CONTENTSSERVICE MANUAL INTRODUCTION QUALIFICATIONS - QUALIFIED SERVICE AGENTSERVICE WARNING IMPORTANT SERVICE REMINDERTOOLS REQUIRED INSTRUCTION MANUALTHERMAL EXPANSION INSTALLATION CONSIDERATIONSCLOSED WATER SYSTEMS Grounding Power SupplyELECTRICAL REQUIREMENTS SERVICE PRECAUTIONS PRE SERVICE CHECKSWIRING CONNECTIONS ELECTRONIC CONTROL MODELS HEATING ELEMENT CONFIGURATIONSWATER HEATER CONSTRUCTION SURFACE MOUNT CONTROL MODELSWATER HEATER CONSTRUCTION SURFACE MOUNT CONTROL MODELSWATER HEATER CONSTRUCTION Amperage OPERATION & SERVICEPRINCIPLES OF ELECTRICITY VoltageCalculating Amps/Ohms/Volts/Watts Ohms Law applied to “SINGLE PHASE” 1Ø powerOhms Law L1 L2 L3 SINGLE AND THREE PHASE POWERChecking Single Phase 1Ø Power 3 L1 and L3 terminals of the water heater’s Power Distribution Block Checking Three Phase 3Ø Power1 L1 and L2 terminals of the water heater’s Power Distribution Block 2 L2 and L3 terminals of the water heater’s Power Distribution BlockSurface Mount Control Models Single Phase to Three Phase PHASE CONVERSIONS - SURFACE MOUNT CONTROL MODELSSurface Mount Control Models Three Phase to Single Phase Electronic Control Models Single Phase to Three Phase PHASE CONVERSIONS - ELECTRONIC CONTROL MODELSElectronic Control Models Three Phase to Single Phase Volt Meter Method FUSESOhm Meter Method SURFACE MOUNT THERMOSTATS Thermostat & ECO Test Wire conductor inside tube HEATING ELEMENTSHeating Element Construction TOTAL Heating Element ConfigurationsNUMBER OF FACTORY INSTALLED Heating Element Ratings208 VAC Heating Element AmperageELEMENT APPROXIMATE CURRENT - AMPSHeating Element Amperage Test Heating Element Voltage Test Measuring Resistance Heating Element Resistance & Ground TestsReplacing Heating Elements Heating Element Ground TestThree Current Sensors Element Sensor Functions ELEMENT SENSORSElement Sensor Construction Element SensorElement Sensor Operation Contactor Construction - How They Work CONTACTORSContactors Contactor ConfigurationsPower Connection Terminals Element Numbers/Connections Wire Colors to ElementsPhysically Operate Mechanical Contactor InspectionContactor Coil Voltage - At Contactor Contactor Coil Voltage - At CCB H1 H2 H3 H4 H5 N/A Primary Winding Secondary Winding 120 VAC Control Circuit Transformer WiringX1 120 VAC TRANSFORMERSSecondary Winding Voltage Test 120 VAC Control Circuit Transformer TestPrimary Winding Voltage Test 24 VAC Transformer Test Temperature Sensor ECO High Temperature Limit SwitchIMMERSION TEMPERATURE PROBE WATER TEMPERATURE Temperature Sensor Resistance TestTemperature Sensor Resistance Data Checking Temperature Sensor ResistanceDC Voltage To Temperature Sensor Temperature Sensor DC Voltage TestECO Continuity Test Checking ECO Switch ContinuityGround Connection ECO Voltage Test120 VAC To ECO 120 VAC From ECOUIM User Interface Module CCB Central Control Board ELECTRONIC CONTROLSCCB - CENTRAL CONTROL BOARD J4 Wiring Terminals - Contactor Coils CCB Socket & Wiring Terminal IdentificationJ2 Socket - 120 VAC Power Supply J3 Wiring Terminals - Alarm Output Relay see pageJ13 Socket - Heating Element Sensors Bank J7 Socket - Enable / Disable Circuits 1 & 2 see pages 45J16 Socket - Not Used J17 Wiring Terminals - Not Used J8 Socket - Not Used J9 Socket - Not Used J10 Socket - Not UsedCCB Enable/Disable Circuits Test Checking for Ground Checking Power and Ground To The CCBChecking for 120 VAC UIM Circuit Board Front Service Notes - Button Pad Ribbon CableUIM - USER INTERFACE MODULE UIM Circuit Board BackUIM - User Interface Module CONTROL SYSTEM FEATURESELECTRONIC CONTROL SYSTEM CONTROL SYSTEM NAVIGATIONTHE DESKTOP SCREEN ICON Table 1 Status IconsMENUS† Table 2 - Operating StatesTable 3 - Control System Menus STATETank Temperature Differential SettingsTEMPERATURES MENU Operating Set PointTemperature Settings HEATER STATUS MENU Enable / Disable 1Alarm Condition Alarm Relay OutputCurrent Time ECONOMY MODE SETUP MENUSetpoint Adjustment Desktop Screen During Economy Mode Economy Mode Setup MenuEconomy Mode Settings Setpoint Adjustment Value Economy Mode Settings Time Clock Settings Normal Operation Between Economy Mode Settings Daily Operating Mode SettingsEconomy Mode All Day Alarm Output Settings ALARM OUTPUT SETUP MENUTemp Alarm SP Used for external Alarm SPBacklight Delay DISPLAY SETTINGS MENUDisplay Settings Temperature UnitsBank # Cycles HEATER INFORMATION MENUElapsed Time Total Heating TimeMain Menu - Current Fault Selected Fault History Menu CURRENT FAULT / ALERT MENUFAULT HISTORY MENU FAULT OCCURRENCE MENUFactory Default User Settings RESTORE FACTORY DEFAULTS MENURestore Factory Defaults Not Enough Hot Water TROUBLESHOOTINGCOMMON SERVICE PROBLEMS No Hot WaterAlert Conditions Fault ConditionsResetting Control System CONTROL SYSTEM UNRESPONSIVEUIM is Inoperable Heating Cycle DisabledControl System Unresponsive cont “No Current Detected” FAULT AND ALERT MESSAGES“Temp Probe Short” Fault & Alert Messages“Temp Probe Open” “Energy Cut Out ECO” Page Page Page Page Technical Support and Parts