GTO SL-1000, SL-2000 installation manual Step

Page 21

STEP 9

Run the low voltage wire from the electrical outlet to the control box. Do not exceed 1000'.

NOTE: Pull approximately 1 foot of extra low voltage wire into the control box to accommodate terminal connections. To maintain adequate charging power, use appropriate gauge, stranded, direct burial wire (see Accessory Catalog). Do not use telephone wire or any solid core wire because it will not provide adequate current. Never splice wires together.

INSTALLATION OF THE GTO TRANSFORMER CONT.

Illustration I

Transformer

Spade Tongue terminal

Red

Black

STEP 10:

Strip 3/16" off the ends of the low voltage wire and attach ends to the transformer terminals; red wire to [RED], black wire to [BLK], (see Illustration I). A dab of household petroleum jelly on each terminal will help prevent corrosion.

We recommend crimping a spade-tongue terminal (not provided) to the end of each wire before attaching it to the transformer.

To prevent damage to transformer, make sure the exposed wire ends do not touch each other!

DO NOT plug the transformer into outlet.

The transformer will be plugged in during STEP 13.

NOTE: Wires coming from the ground to the control box should be run through PVC conduit to protect them from lawn mowers, weed eaters and grazing animals (see illustrations on page 13).

STEP 11:

Feed the low voltage wires upward through the strain relief on the bottom of the control box (see Illustration J). Pull 6" to 8" of wire into the control box.

If accessories (i.e. safety loops, card readers, etc.) are to be added during this installation, do not tighten the strain relief screw against the wires until the accessories have been connected. When all accessories have been connected, fully tighten the strain relief screw against the wires.

Illustration J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLOSE

 

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

 

 

 

 

 

.

 

ST

 

 

 

 

 

+

 

 

 

 

 

INERTIA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OBSTRUC

T

 

 

 

 

 

 

 

 

 

SENS.

 

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

 

 

 

 

 

 

 

 

LEARN

 

 

 

 

 

 

 

BLU GRN CLSEDG OPNEDG

GRN ORG BLU WHT

R G B

 

 

 

 

 

OPNEDG

 

 

 

SOLAR RED BLK

ORG BLU GRN CLSEDG

RED BLK ORG

 

RCVR

 

ACCESSORY

 

 

18VAC~ ~

+

 

 

 

OPERATOR

ALARM

 

 

 

 

 

 

 

SECOND

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

 

IN

FIRST OPERATOR

 

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿￿￿￿￿￿￿￿￿￿

 

18

 

 

 

 

 

 

 

 

 

 

Image 21
Contents Automatic Gate Operator Vehicular Gate Operator Class Categories When You Know Multiply By To Find SymbolTable of Contents Important Safety Instructions Before Installation For the InstallerII. During Installation For the System DesignerIII. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325No ONE should Cross the Path of the Moving Gate For the CONSUMER/END UserPoint hazard Required Safety Precautions for GatesSeries Moving Gate Can Cause Injury Or Death GTO PRO SL-1000 Series Technical Specifications GTO PRO SL-2000 Series Technical Specifications Parts Identification Single Gate Operator Installation Overview of Operator InstallationGate Preparation Mounting the Legs on the Slide Gate Operator Recommended Wiring and USE of ConduitOperator side of the gate see Overview Illustration, Determining the Mounting Position and Mounting the OperatorTo Open the Gate Manually Installing the ChainPowering the System Connecting the BatteryInstallation of the GTO Transformer Estimated Maximum Number of Cycles Per Day Solar Zones and Gate ActivityStep 18VAC Another see Illustration KRight Control Board SettingsPotentiometers Setting the Personal Transmitter Code FCC Regulation Mounting the ReceiverIf your gate opens from Right to Left Adjusting the Limit SwitchesHowever, if your gate opens from Left to Right Counter ClockwiseConnecting Additional Safety Devices Connecting Safety DevicesWHT White Used with GRN Green Connecting AccessoriesBLU Blue Used with GRN Green ORG Orange Used with GRN GreenAttaching the Housing Is especially important for safety devices MaintenanceMaintenance Trouble Shooting GuideConnected to these terminals System Test SpecificationsWarranty and Repair Service Limited Two Year WarrantyInstructions for the Installation Dual Slide Gate System Second Gate Auxiliary Operator Parts & Hardware Dual Gate System InstallationControl Unit This Step is for SL-2000/ 2200 Installation only Wiring the Second OperatorRefer to the illustrations on the next Setting the Control Board for Dual Gate InstallationsStep GTO Digital Keypad F300 Accessories Available Through Your DealerACCESS-ORIES Replacement Batteries Installation of this operator conforms to Class Installation Check List

SL-1000, SL-2000 specifications

The GTO SL-2000 and SL-1000 are advanced gate operators designed for efficient and reliable automation of heavy-duty swing gates. These models are renowned for their robust construction and innovative technologies that enhance both performance and security.

The SL-2000 is particularly suited for large, dual-swing gates weighing up to 2,000 pounds, making it a perfect choice for commercial and industrial settings. In comparison, the SL-1000 is designed for lighter gates that weigh up to 1,000 pounds, suitable for residential and light commercial applications. Both models are engineered to provide smooth, quiet operation, which is vital for residential areas where noise reduction is essential.

One of the standout features of both the SL-2000 and SL-1000 is their advanced DC motor technology. This allows for variable speed operation, providing a slower, more controlled movement during the opening and closing cycles. Such functionality not only enhances safety but also minimizes wear and tear on the gate mechanism, ensuring longevity.

Both models are equipped with obstacle detection technology that halts the gate's movement if an obstruction is encountered. This safety feature helps prevent accidents and damage, a critical aspect in environments where individuals and vehicles are present.

In terms of installation, the GTO SL series is designed for ease of use, featuring a straightforward setup process with clear instructions and minimal tools required. Additionally, the SL-2000 and SL-1000 include a built-in rechargeable battery backup, ensuring that the gate operates even during power outages.

Security is a top priority with both gate operators. They incorporate rolling code technology in their remote controls, which changes the access code with each activation, significantly reducing the risk of unauthorized access. Furthermore, the SL series supports multiple remote controls, allowing for convenient access for users while maintaining security.

Durability is another hallmark of the GTO SL-2000 and SL-1000. Both operators are built with weather-resistant materials, ensuring they can withstand various environmental conditions. This resilience makes them a solid investment for long-term use.

In conclusion, the GTO SL-2000 and SL-1000 are state-of-the-art gate operators that combine cutting-edge technology with superior safety features, making them a reliable choice for enhancing the automation of swing gates in diverse applications. Their ease of installation, robust construction, and advanced functionalities are significant advantages for property owners seeking secure and efficient access solutions.