Brother Computerized Embroidery Machine operation manual Important Safety Instructions

Page 2

————————————————————————————————————————————————————

Important Safety Instructions

Please read these safety instructions before attempting to use the machine. This machine is intended for household use.

DANGER - To reduce the risk of electric shock

1Always unplug the machine from the electrical outlet immediately after using, when cleaning,

when making any user servicing adjustments mentioned in this manual, or if you are leaving the

machine unattended.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons. 2Always unplug the machine from the electrical outlet when removing covers, lubricating, or

when making any adjustments mentioned in the instruction manual.

•To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull it out of the electrical outlet. Do not pull on the cord.

•Plug the machine directly into the electrical outlet. Do not use an extension cord.

•Always unplug your machine if the power is cut.

3 Never operate this machine if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest

authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

4 Always keep your work area clear:

•Never operate the machine with any air openings blocked. Keep ventilation openings of the machine free from the build up of lint, dust, and loose cloth.

•Do not use extension cords. Plug the machine directly into the electrical outlet.

•Never drop or insert any object into any opening.

•Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

5 Special care is required when embroidering:

•Always pay close attention to the needle. Do not use bent or damaged needles.

•Keep fingers away from all moving parts. Special care is required around the machine needle.

•Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.

•Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

•Do not push or pull the fabric when embroidering.

1

Image 2

Contents Getting Ready Embroidery Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Contents Appendix Machine Features Introduction75/11 3 needles 90/14 1 needle AccessoriesIncluded accessories Optional accessories Following are available as optional accessoriesNames of Machine Parts and Their Functions Front viewNeedle and embroidery foot section Right-side/rear viewOperation buttons Start/stop buttonOperation panel Previous page keyPage Installing the bobbin Upper Threading Getting ReadyEmbroidery Step by Step Basic steps for embroidery are as followsBarm Embroidery unit precautions Attaching the embroidery unitAttaching the Embroidery Unit CTurn on the machinePress , and then press Removing the embroidery unitRemove the embroidery frame CTurn off the machineEmbroidery unit separates from the machine Power supply precautions Turning the Machine On/OffTurning on the machine CUnplug the power supply cord from the electrical outletUnplug the power supply cord from the power supply jack Turning off the machinePattern type selection screen LCD Liquid Crystal Display OperationViewing the LCD Changing the machine settings DetailsTurn on the machine BPresspanel. Settings key on the operationDWhenkey. settings are complete, press Back CPress the item to be setPress Help key on the operation panel Checking machine operating proceduresDPressnext page. Next page key to switch to CPress the item to be displayedWinding the bobbin Winding/Installing the BobbinBobbin precautions BOpen the top coverPlace the spool of thread for the bobbin onto the spool pin GSlide the spool cap onto the spool pinMake sure that the thread passes under the pretension disk Guide slit in bobbin winder seat with built-in cutter Installing the bobbin Slide the bobbin cover latch to the rightGReattach the bobbin cover Threading the upper thread Upper ThreadingAbout the spool of thread Upper Threading DOpen the top coverThreading the needle CLower the presser foot lever to lower the embroidery foot AThreadguide. the machine to the needle bar thread BLower the presser foot leverChecking the needle Needle precautionsReplacing the Needle Replacing the needle Needle stopper Getting Ready Editing and Saving Patterns Removing the embroidery frame Selecting Embroidery PatternsSold separately Embroidering ResewingFabric Embroidering NeatlyWhat to prepare Stabilizer materialNeedle OtherAttaching a stabilizer material to the fabric † When it cannot be ironed or placed in the hoopPreparing the Fabric Embroidery frame mediumoption Setting the fabric in the embroidery frameEmbroidery frame large Embroidery frame smalloptionCPressfabric.the inner frame in from the top ERemove the embroidery sheet Using embroidery sheetsBPlace the embroidery sheet on the inner frame We recommend stabilizer material for all embroidery Raise the presser foot lever Attaching the Embroidery FrameAttaching the embroidery frame Removing the embroidery frame Embroidery pattern types Selecting Embroidery PatternsCopyright information Alphabet patternsLCD liquid crystal display operation Operation keysLCD button Selecting characters † Example WelcomeSelecting an embroidery pattern Embroidery patternsBSelect the frame shape Selecting a frame patternPress the frame pattern CSelect the stitchUsing an embroidery card sold separately Select a patternThread Upper thread EmbroideringEmbroidering attractive finishes Bobbin threadEmbroidering a pattern Prepareon the screen.embroidery thread of the color shown cAfter progressing 5-6 stitches, press CLower the presser foot leverDPress Start/stop button GPress Start/stop button againAppliquéing Select an appliqué patternILower the presser foot lever, and press Start/stop button Editing and Saving Patterns Adjusting the layoutCCheck and adjust the layout After.selecting the embroidery pattern, pressPress Back key to return to the previous screen Storing a pattern Storing patternsDPress Back key to return to the original screen AAfter selecting the pattern to be stored, press Memory keyAdjusting the thread tension Restart the embroidery ResewingThread runs out partway through a design DPress Stopping while embroideringCPress Embroidery key Turn off the machineKRestart the embroidery Embroidery Appendix Cleaning the race Care and MaintenanceCleaning the machine surface Remove the bobbin caseCare and Maintenance CRaise the presser foot lever Attaching the Embroidery FootAttaching the embroidery Foot Q DHold the embroidery foot with your right hand, as shownAttaching the Embroidery Foot Troubleshooting Not operateTroubleshooting Is tangled orSkipped Carriage or embroidery frame Place objects within the range Error messages Error Message Probable CauseRefer to Error Message Probable Cause CPress or DTurn off the machine, then turn it on again Adjusting the LCDOperation beep Canceling the operation beep Index Settings key English 882-U30 XD1628-051