Brother Computerized Embroidery Machine operation manual GReattach the bobbin cover

Page 30

————————————————————————————————————————————————————

fPass the thread through the slot as shown, and then pull the thread out toward the front.

1

aCutter

XThe cutter cuts the thread.

Note

zMake sure that the thread is correctly inserted through the tension-adjusting spring of the bobbin case. If it is not inserted correctly, reinsert the thread.

1

aTension-adjusting spring

gReattach the bobbin cover.

Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side.

2

1

XThe lower threading is finished.

Next, thread the upper thread. Continue with the procedure in “Upper Threading” (page 30).

Memo

zYou can start embroidering without pulling up the bobbin thread.

1

Winding/Installing the Bobbin 29

Image 30

Contents Getting Ready Embroidery Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Contents Appendix Machine Features IntroductionAccessories Included accessories75/11 3 needles 90/14 1 needle Optional accessories Following are available as optional accessoriesNames of Machine Parts and Their Functions Front viewNeedle and embroidery foot section Right-side/rear viewOperation buttons Start/stop buttonOperation panel Previous page keyPage Installing the bobbin Upper Threading Getting ReadyEmbroidery Step by Step Basic steps for embroidery are as followsBarm Embroidery unit precautions Attaching the embroidery unitAttaching the Embroidery Unit CTurn on the machinePress , and then press Removing the embroidery unitRemove the embroidery frame CTurn off the machineEmbroidery unit separates from the machine Power supply precautions Turning the Machine On/OffTurning on the machine CUnplug the power supply cord from the electrical outletUnplug the power supply cord from the power supply jack Turning off the machineLCD Liquid Crystal Display Operation Viewing the LCDPattern type selection screen Changing the machine settings DetailsTurn on the machine BPresspanel. Settings key on the operationDWhenkey. settings are complete, press Back CPress the item to be setPress Help key on the operation panel Checking machine operating proceduresDPressnext page. Next page key to switch to CPress the item to be displayedWinding the bobbin Winding/Installing the BobbinBobbin precautions BOpen the top coverPlace the spool of thread for the bobbin onto the spool pin GSlide the spool cap onto the spool pinMake sure that the thread passes under the pretension disk Guide slit in bobbin winder seat with built-in cutter Installing the bobbin Slide the bobbin cover latch to the rightGReattach the bobbin cover Upper Threading About the spool of threadThreading the upper thread Upper Threading DOpen the top coverThreading the needle CLower the presser foot lever to lower the embroidery foot AThreadguide. the machine to the needle bar thread BLower the presser foot leverNeedle precautions Replacing the NeedleChecking the needle Replacing the needle Needle stopper Getting Ready Editing and Saving Patterns Removing the embroidery frame Selecting Embroidery PatternsSold separately Embroidering ResewingFabric Embroidering NeatlyWhat to prepare Stabilizer materialNeedle Other† When it cannot be ironed or placed in the hoop Preparing the FabricAttaching a stabilizer material to the fabric Embroidery frame mediumoption Setting the fabric in the embroidery frameEmbroidery frame large Embroidery frame smalloptionCPressfabric.the inner frame in from the top Using embroidery sheets BPlace the embroidery sheet on the inner frameERemove the embroidery sheet We recommend stabilizer material for all embroidery Attaching the Embroidery Frame Attaching the embroidery frameRaise the presser foot lever Removing the embroidery frame Embroidery pattern types Selecting Embroidery PatternsCopyright information Alphabet patternsLCD liquid crystal display operation Operation keysLCD button Selecting characters † Example WelcomeSelecting an embroidery pattern Embroidery patternsBSelect the frame shape Selecting a frame patternPress the frame pattern CSelect the stitchUsing an embroidery card sold separately Select a patternThread Upper thread EmbroideringEmbroidering attractive finishes Bobbin threadEmbroidering a pattern Prepareon the screen.embroidery thread of the color shown cAfter progressing 5-6 stitches, press CLower the presser foot leverDPress Start/stop button GPress Start/stop button againAppliquéing Select an appliqué patternILower the presser foot lever, and press Start/stop button Editing and Saving Patterns Adjusting the layoutCCheck and adjust the layout After.selecting the embroidery pattern, pressPress Back key to return to the previous screen Storing a pattern Storing patternsDPress Back key to return to the original screen AAfter selecting the pattern to be stored, press Memory keyAdjusting the thread tension Resewing Thread runs out partway through a designRestart the embroidery DPress Stopping while embroideringCPress Embroidery key Turn off the machineKRestart the embroidery Embroidery Appendix Cleaning the race Care and MaintenanceCleaning the machine surface Remove the bobbin caseCare and Maintenance CRaise the presser foot lever Attaching the Embroidery FootAttaching the embroidery Foot Q DHold the embroidery foot with your right hand, as shownAttaching the Embroidery Foot Troubleshooting Not operateTroubleshooting Is tangled orSkipped Carriage or embroidery frame Place objects within the range Error messages Error Message Probable CauseRefer to Error Message Probable Cause Adjusting the LCD Operation beepCPress or DTurn off the machine, then turn it on again Canceling the operation beep Index Settings key English 882-U30 XD1628-051