Brother Computerized Embroidery Machine For Users in the UK, EIRE, Malta and Cyprus only

Page 3

———————————————————————————————————————————————————

6 This machine is not a toy:

•Your close attention is necessary when the machine is used by or near children.

•Do not use outdoors.

7 For a longer service life:

•When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects.

•Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.

•Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.

8 For repair or adjustment:

•If the Light unit is damaged, it must be replaced by authorized dealer.

•In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.

Use this machine only for its intended use as described in the manual.

Use accessories recommended by the manufacturer as contained in this manual.

Save these instructions.

The contents of this manual and specifications of this product are subject to change without notice. For additional product information and updates, visit our web site at www.brother.com

FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY

IMPORTANT

•In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

•Always replace the fuse cover. Never use plugs with the fuse cover omitted.

•If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.

FOR USERS IN AUSTRALIA AND NEW ZEALAND

This embroidery machine is not intended to be used by young children, and assistance may be required if used by a person with a disability.

2

Image 3

Contents Getting Ready Embroidery Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Contents Appendix Introduction Machine FeaturesAccessories Included accessories75/11 3 needles 90/14 1 needle Following are available as optional accessories Optional accessoriesFront view Names of Machine Parts and Their FunctionsRight-side/rear view Needle and embroidery foot sectionStart/stop button Operation buttonsPrevious page key Operation panelPage Getting Ready Installing the bobbin Upper ThreadingBasic steps for embroidery are as follows Embroidery Step by StepCTurn on the machine Embroidery unit precautions Attaching the embroidery unitAttaching the Embroidery Unit BarmCTurn off the machine Removing the embroidery unitRemove the embroidery frame Press , and then pressEmbroidery unit separates from the machine Turning the Machine On/Off Power supply precautionsTurning off the machine CUnplug the power supply cord from the electrical outletUnplug the power supply cord from the power supply jack Turning on the machineLCD Liquid Crystal Display Operation Viewing the LCDPattern type selection screen Details Changing the machine settingsCPress the item to be set BPresspanel. Settings key on the operationDWhenkey. settings are complete, press Back Turn on the machineCPress the item to be displayed Checking machine operating proceduresDPressnext page. Next page key to switch to Press Help key on the operation panelBOpen the top cover Winding/Installing the BobbinBobbin precautions Winding the bobbinGSlide the spool cap onto the spool pin Place the spool of thread for the bobbin onto the spool pinMake sure that the thread passes under the pretension disk Guide slit in bobbin winder seat with built-in cutter Slide the bobbin cover latch to the right Installing the bobbinGReattach the bobbin cover Upper Threading About the spool of threadThreading the upper thread DOpen the top cover Upper ThreadingThreading the needle CLower the presser foot lever to lower the embroidery foot BLower the presser foot lever AThreadguide. the machine to the needle bar threadNeedle precautions Replacing the NeedleChecking the needle Replacing the needle Needle stopper Getting Ready Resewing Removing the embroidery frame Selecting Embroidery PatternsSold separately Embroidering Editing and Saving PatternsStabilizer material Embroidering NeatlyWhat to prepare FabricOther Needle† When it cannot be ironed or placed in the hoop Preparing the FabricAttaching a stabilizer material to the fabric Embroidery frame smalloption Setting the fabric in the embroidery frameEmbroidery frame large Embroidery frame mediumoptionCPressfabric.the inner frame in from the top Using embroidery sheets BPlace the embroidery sheet on the inner frameERemove the embroidery sheet We recommend stabilizer material for all embroidery Attaching the Embroidery Frame Attaching the embroidery frameRaise the presser foot lever Removing the embroidery frame Alphabet patterns Selecting Embroidery PatternsCopyright information Embroidery pattern typesOperation keys LCD liquid crystal display operationLCD button † Example Welcome Selecting charactersEmbroidery patterns Selecting an embroidery patternCSelect the stitch Selecting a frame patternPress the frame pattern BSelect the frame shapeSelect a pattern Using an embroidery card sold separatelyBobbin thread EmbroideringEmbroidering attractive finishes Thread Upper threadPrepareon the screen.embroidery thread of the color shown c Embroidering a patternGPress Start/stop button again CLower the presser foot leverDPress Start/stop button After progressing 5-6 stitches, pressSelect an appliqué pattern AppliquéingILower the presser foot lever, and press Start/stop button After.selecting the embroidery pattern, press Adjusting the layoutCCheck and adjust the layout Editing and Saving PatternsPress Back key to return to the previous screen AAfter selecting the pattern to be stored, press Memory key Storing patternsDPress Back key to return to the original screen Storing a patternAdjusting the thread tension Resewing Thread runs out partway through a designRestart the embroidery Turn off the machine Stopping while embroideringCPress Embroidery key DPressKRestart the embroidery Embroidery Appendix Remove the bobbin case Care and MaintenanceCleaning the machine surface Cleaning the raceCare and Maintenance DHold the embroidery foot with your right hand, as shown Attaching the Embroidery FootAttaching the embroidery Foot Q CRaise the presser foot leverAttaching the Embroidery Foot Not operate TroubleshootingIs tangled or TroubleshootingSkipped Carriage or embroidery frame Place objects within the range Error Message Probable Cause Error messagesRefer to Error Message Probable Cause Adjusting the LCD Operation beepCPress or DTurn off the machine, then turn it on again Canceling the operation beep Index Settings key English 882-U30 XD1628-051