Brother Computerized Embroidery Machine Turning on the machine, Turning off the machine

Page 20

————————————————————————————————————————————————————

Turning on the machine

Before turning on the machine, be sure to attach the embroidery unit to it. If the embroidery unit is not attached, the machine does not operate. (For details, refer to “Attaching the Embroidery Unit” (page 15).)

Prepare the included power cord.

aMake sure that the machine is turned off (the main power switch is set to “ ”), and then plug the power supply cord into the power supply jack on the right side of the machine.

bInsert the plug of the power supply cord into a household electrical outlet.

1

aPower supply jack

cPress the right side of the main power switch on the right side of the machine to turn the machine on (set it to “”).

XThe lamps, LCD and (Start/stop button) light up when the machine is turned on.

Turning off the machine

When you are finished using the machine, turn it off.
In addition, before transporting the machine to	1
another location, be sure to turn it off.	1

aMakestopped.sure that the machine is completely

bPress the left side of the main power switch on the right side of the machine to turn the machine off (set it to “ ”).

XThe lamps go off when the machine is turned off.

cUnplug the power supply cord from the electrical outlet.

Grasp the plug when unplugging the power supply cord.

dUnplug the power supply cord from the power supply jack.

Note

zIf a power outage occurs while the machine is being operated, turn off the machine and unplug the power supply cord. When restarting the machine, follow the necessary procedure to correctly operate the machine.

(For U.S.A. only)

zThis appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

Turning the Machine On/Off 19

Image 20

Contents Getting Ready Embroidery Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Contents Appendix Machine Features Introduction75/11 3 needles 90/14 1 needle AccessoriesIncluded accessories Optional accessories Following are available as optional accessoriesNames of Machine Parts and Their Functions Front viewNeedle and embroidery foot section Right-side/rear viewOperation buttons Start/stop buttonOperation panel Previous page keyPage Installing the bobbin Upper Threading Getting ReadyEmbroidery Step by Step Basic steps for embroidery are as followsEmbroidery unit precautions Attaching the embroidery unit Attaching the Embroidery UnitBarm CTurn on the machineRemoving the embroidery unit Remove the embroidery framePress , and then press CTurn off the machineEmbroidery unit separates from the machine Power supply precautions Turning the Machine On/OffCUnplug the power supply cord from the electrical outlet Unplug the power supply cord from the power supply jackTurning on the machine Turning off the machinePattern type selection screen LCD Liquid Crystal Display OperationViewing the LCD Changing the machine settings DetailsBPresspanel. Settings key on the operation DWhenkey. settings are complete, press BackTurn on the machine CPress the item to be setChecking machine operating procedures DPressnext page. Next page key to switch toPress Help key on the operation panel CPress the item to be displayedWinding/Installing the Bobbin Bobbin precautionsWinding the bobbin BOpen the top coverPlace the spool of thread for the bobbin onto the spool pin GSlide the spool cap onto the spool pinMake sure that the thread passes under the pretension disk Guide slit in bobbin winder seat with built-in cutter Installing the bobbin Slide the bobbin cover latch to the rightGReattach the bobbin cover Threading the upper thread Upper ThreadingAbout the spool of thread Upper Threading DOpen the top coverThreading the needle CLower the presser foot lever to lower the embroidery foot AThreadguide. the machine to the needle bar thread BLower the presser foot leverChecking the needle Needle precautionsReplacing the Needle Replacing the needle Needle stopper Getting Ready Removing the embroidery frame Selecting Embroidery Patterns Sold separately EmbroideringEditing and Saving Patterns ResewingEmbroidering Neatly What to prepareFabric Stabilizer materialNeedle OtherAttaching a stabilizer material to the fabric † When it cannot be ironed or placed in the hoopPreparing the Fabric Setting the fabric in the embroidery frame Embroidery frame largeEmbroidery frame mediumoption Embroidery frame smalloptionCPressfabric.the inner frame in from the top ERemove the embroidery sheet Using embroidery sheetsBPlace the embroidery sheet on the inner frame We recommend stabilizer material for all embroidery Raise the presser foot lever Attaching the Embroidery FrameAttaching the embroidery frame Removing the embroidery frame Selecting Embroidery Patterns Copyright informationEmbroidery pattern types Alphabet patternsLCD liquid crystal display operation Operation keysLCD button Selecting characters † Example WelcomeSelecting an embroidery pattern Embroidery patternsSelecting a frame pattern Press the frame patternBSelect the frame shape CSelect the stitchUsing an embroidery card sold separately Select a patternEmbroidering Embroidering attractive finishesThread Upper thread Bobbin threadEmbroidering a pattern Prepareon the screen.embroidery thread of the color shown cCLower the presser foot lever DPress Start/stop buttonAfter progressing 5-6 stitches, press GPress Start/stop button againAppliquéing Select an appliqué patternILower the presser foot lever, and press Start/stop button Adjusting the layout CCheck and adjust the layoutEditing and Saving Patterns After.selecting the embroidery pattern, pressPress Back key to return to the previous screen Storing patterns DPress Back key to return to the original screenStoring a pattern AAfter selecting the pattern to be stored, press Memory keyAdjusting the thread tension Restart the embroidery ResewingThread runs out partway through a design Stopping while embroidering CPress Embroidery keyDPress Turn off the machineKRestart the embroidery Embroidery Appendix Care and Maintenance Cleaning the machine surfaceCleaning the race Remove the bobbin caseCare and Maintenance Attaching the Embroidery Foot Attaching the embroidery Foot QCRaise the presser foot lever DHold the embroidery foot with your right hand, as shownAttaching the Embroidery Foot Troubleshooting Not operateTroubleshooting Is tangled orSkipped Carriage or embroidery frame Place objects within the range Error messages Error Message Probable CauseRefer to Error Message Probable Cause CPress or DTurn off the machine, then turn it on again Adjusting the LCDOperation beep Canceling the operation beep Index Settings key English 882-U30 XD1628-051