Brother Computerized Embroidery Machine Names of Machine Parts and Their Functions, Front view

Page 9

———————————————————————————————————————————————————

Names of Machine Parts and Their Functions

The names of the various parts of the machine and their functions are described below. Before using the machine, carefully read these descriptions to learn the names of the machine parts.

Front view

aThread guide plate

Pass the thread around the thread guide plate when threading the upper thread.

bThread guide cover

Like with the thread guide plate, pass the thread around the thread guide cover when threading the upper thread.

cSpool pin

Place a spool of thread on the spool pin.

dBobbin winding thread guide

Pass the thread around this thread guide when winding the bobbin thread.

eTop cover

Open the top cover to place the spool of thread on the spool pin.

fBobbin winder

Use the bobbin winder when winding the bobbin.

gOperation panel

From the operation panel, patterns can be selected and edited, and operations for using the machine can be displayed (page 11).

hEmbroidery unit connector slot

Plug in the connector for the embroidery unit.

iPresser foot lever

Raise and lower the presser foot lever to raise and lower the presser foot

jOperation buttons

Use these buttons to operate the machine.

kEmbroidery unit

Attach the embroidery unit to the machine, and then attach the embroidery frame.

lThread cutter

Pass the threads through the thread cutter to cut them.

mNeedle threader lever

Use the needle threader lever to thread the needle.

nThread take-up lever check window

Look through the window to check the position of the take-up lever.

8

Image 9

Contents Getting Ready Embroidery Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Contents Appendix Introduction Machine FeaturesAccessories Included accessories75/11 3 needles 90/14 1 needle Following are available as optional accessories Optional accessoriesFront view Names of Machine Parts and Their FunctionsRight-side/rear view Needle and embroidery foot sectionStart/stop button Operation buttonsPrevious page key Operation panelPage Getting Ready Installing the bobbin Upper ThreadingBasic steps for embroidery are as follows Embroidery Step by StepAttaching the Embroidery Unit Embroidery unit precautions Attaching the embroidery unitBarm CTurn on the machineRemove the embroidery frame Removing the embroidery unitPress , and then press CTurn off the machineEmbroidery unit separates from the machine Turning the Machine On/Off Power supply precautionsUnplug the power supply cord from the power supply jack CUnplug the power supply cord from the electrical outletTurning on the machine Turning off the machineLCD Liquid Crystal Display Operation Viewing the LCDPattern type selection screen Details Changing the machine settingsDWhenkey. settings are complete, press Back BPresspanel. Settings key on the operationTurn on the machine CPress the item to be setDPressnext page. Next page key to switch to Checking machine operating proceduresPress Help key on the operation panel CPress the item to be displayedBobbin precautions Winding/Installing the BobbinWinding the bobbin BOpen the top coverGSlide the spool cap onto the spool pin Place the spool of thread for the bobbin onto the spool pinMake sure that the thread passes under the pretension disk Guide slit in bobbin winder seat with built-in cutter Slide the bobbin cover latch to the right Installing the bobbinGReattach the bobbin cover Upper Threading About the spool of threadThreading the upper thread DOpen the top cover Upper ThreadingThreading the needle CLower the presser foot lever to lower the embroidery foot BLower the presser foot lever AThreadguide. the machine to the needle bar threadNeedle precautions Replacing the NeedleChecking the needle Replacing the needle Needle stopper Getting Ready Sold separately Embroidering Removing the embroidery frame Selecting Embroidery PatternsEditing and Saving Patterns ResewingWhat to prepare Embroidering NeatlyFabric Stabilizer materialOther Needle† When it cannot be ironed or placed in the hoop Preparing the FabricAttaching a stabilizer material to the fabric Embroidery frame large Setting the fabric in the embroidery frameEmbroidery frame mediumoption Embroidery frame smalloptionCPressfabric.the inner frame in from the top Using embroidery sheets BPlace the embroidery sheet on the inner frameERemove the embroidery sheet We recommend stabilizer material for all embroidery Attaching the Embroidery Frame Attaching the embroidery frameRaise the presser foot lever Removing the embroidery frame Copyright information Selecting Embroidery PatternsEmbroidery pattern types Alphabet patternsOperation keys LCD liquid crystal display operationLCD button † Example Welcome Selecting charactersEmbroidery patterns Selecting an embroidery patternPress the frame pattern Selecting a frame patternBSelect the frame shape CSelect the stitchSelect a pattern Using an embroidery card sold separatelyEmbroidering attractive finishes EmbroideringThread Upper thread Bobbin threadPrepareon the screen.embroidery thread of the color shown c Embroidering a patternDPress Start/stop button CLower the presser foot leverAfter progressing 5-6 stitches, press GPress Start/stop button againSelect an appliqué pattern AppliquéingILower the presser foot lever, and press Start/stop button CCheck and adjust the layout Adjusting the layoutEditing and Saving Patterns After.selecting the embroidery pattern, pressPress Back key to return to the previous screen DPress Back key to return to the original screen Storing patternsStoring a pattern AAfter selecting the pattern to be stored, press Memory keyAdjusting the thread tension Resewing Thread runs out partway through a designRestart the embroidery CPress Embroidery key Stopping while embroideringDPress Turn off the machineKRestart the embroidery Embroidery Appendix Cleaning the machine surface Care and MaintenanceCleaning the race Remove the bobbin caseCare and Maintenance Attaching the embroidery Foot Q Attaching the Embroidery FootCRaise the presser foot lever DHold the embroidery foot with your right hand, as shownAttaching the Embroidery Foot Not operate TroubleshootingIs tangled or TroubleshootingSkipped Carriage or embroidery frame Place objects within the range Error Message Probable Cause Error messagesRefer to Error Message Probable Cause Adjusting the LCD Operation beepCPress or DTurn off the machine, then turn it on again Canceling the operation beep Index Settings key English 882-U30 XD1628-051