Brother Computerized Embroidery Machine operation manual Attaching the Embroidery Foot

Page 74

————————————————————————————————————————————————————

fSecure the embroidery foot with the presser foot holder screw.

Set the embroidery foot perpendicular.

gFirmly tighten the presser foot holder screw. Turn the screwdriver toward the front.

CAUTION

●Do not hit the needle with your finger or the embroidery foot when attaching it. The needle may break or cause injury.

●Be sure to tighten the screw with the included screwdriver. If the screw is loose, the needle may hit the embroidery foot and break or bend.

●Before embroidering, always turn the handwheel toward you (counterclockwise) slowly to make sure that the needle does not hit the embroidery foot. Otherwise, the needle may break or bend.

3

Attaching the Embroidery Foot 73

Image 74

Contents Getting Ready Embroidery Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Contents Appendix Machine Features Introduction75/11 3 needles 90/14 1 needle AccessoriesIncluded accessories Optional accessories Following are available as optional accessoriesNames of Machine Parts and Their Functions Front viewNeedle and embroidery foot section Right-side/rear viewOperation buttons Start/stop buttonOperation panel Previous page keyPage Installing the bobbin Upper Threading Getting ReadyEmbroidery Step by Step Basic steps for embroidery are as followsBarm Embroidery unit precautions Attaching the embroidery unitAttaching the Embroidery Unit CTurn on the machinePress , and then press Removing the embroidery unitRemove the embroidery frame CTurn off the machineEmbroidery unit separates from the machine Power supply precautions Turning the Machine On/OffTurning on the machine CUnplug the power supply cord from the electrical outletUnplug the power supply cord from the power supply jack Turning off the machinePattern type selection screen LCD Liquid Crystal Display OperationViewing the LCD Changing the machine settings DetailsTurn on the machine BPresspanel. Settings key on the operationDWhenkey. settings are complete, press Back CPress the item to be setPress Help key on the operation panel Checking machine operating proceduresDPressnext page. Next page key to switch to CPress the item to be displayedWinding the bobbin Winding/Installing the BobbinBobbin precautions BOpen the top coverPlace the spool of thread for the bobbin onto the spool pin GSlide the spool cap onto the spool pinMake sure that the thread passes under the pretension disk Guide slit in bobbin winder seat with built-in cutter Installing the bobbin Slide the bobbin cover latch to the rightGReattach the bobbin cover Threading the upper thread Upper ThreadingAbout the spool of thread Upper Threading DOpen the top coverThreading the needle CLower the presser foot lever to lower the embroidery foot AThreadguide. the machine to the needle bar thread BLower the presser foot leverChecking the needle Needle precautionsReplacing the Needle Replacing the needle Needle stopper Getting Ready Editing and Saving Patterns Removing the embroidery frame Selecting Embroidery PatternsSold separately Embroidering ResewingFabric Embroidering NeatlyWhat to prepare Stabilizer materialNeedle OtherAttaching a stabilizer material to the fabric † When it cannot be ironed or placed in the hoopPreparing the Fabric Embroidery frame mediumoption Setting the fabric in the embroidery frameEmbroidery frame large Embroidery frame smalloptionCPressfabric.the inner frame in from the top ERemove the embroidery sheet Using embroidery sheetsBPlace the embroidery sheet on the inner frame We recommend stabilizer material for all embroidery Raise the presser foot lever Attaching the Embroidery FrameAttaching the embroidery frame Removing the embroidery frame Embroidery pattern types Selecting Embroidery PatternsCopyright information Alphabet patternsLCD liquid crystal display operation Operation keysLCD button Selecting characters † Example WelcomeSelecting an embroidery pattern Embroidery patternsBSelect the frame shape Selecting a frame patternPress the frame pattern CSelect the stitchUsing an embroidery card sold separately Select a patternThread Upper thread EmbroideringEmbroidering attractive finishes Bobbin threadEmbroidering a pattern Prepareon the screen.embroidery thread of the color shown cAfter progressing 5-6 stitches, press CLower the presser foot leverDPress Start/stop button GPress Start/stop button againAppliquéing Select an appliqué patternILower the presser foot lever, and press Start/stop button Editing and Saving Patterns Adjusting the layoutCCheck and adjust the layout After.selecting the embroidery pattern, pressPress Back key to return to the previous screen Storing a pattern Storing patternsDPress Back key to return to the original screen AAfter selecting the pattern to be stored, press Memory keyAdjusting the thread tension Restart the embroidery ResewingThread runs out partway through a design DPress Stopping while embroideringCPress Embroidery key Turn off the machineKRestart the embroidery Embroidery Appendix Cleaning the race Care and MaintenanceCleaning the machine surface Remove the bobbin caseCare and Maintenance CRaise the presser foot lever Attaching the Embroidery FootAttaching the embroidery Foot Q DHold the embroidery foot with your right hand, as shownAttaching the Embroidery Foot Troubleshooting Not operateTroubleshooting Is tangled orSkipped Carriage or embroidery frame Place objects within the range Error messages Error Message Probable CauseRefer to Error Message Probable Cause CPress or DTurn off the machine, then turn it on again Adjusting the LCDOperation beep Canceling the operation beep Index Settings key English 882-U30 XD1628-051