APPENDIX
Symptom | Probable Cause | Remedy | Reference | |
|
|
|
| |
| The upper thread was not | Correct the upper threading. | page 30 | |
| threaded correctly. | |||
|
|
| ||
|
|
|
| |
Stitches are | The needle is bent or blunt. | Replace the needle. | page 35 | |
|
|
| ||
skipped. | The needle is incorrectly installed. | Correctly install the needle. | page 36 | |
| ||||
|
|
|
| |
| Dust has accumulated under the | Remove the needle plate cover and | page 70 | |
| needle plate or in the bobbin case. | clean the race. | ||
|
| |||
|
|
|
| |
| Dust has accumulated in the | Clean the race. | page 70 | |
| bobbin case. | |||
|
|
| ||
|
|
|
| |
| The upper thread was not | Correct the upper threading. | page 30 | |
| threaded correctly. | |||
A |
|
| ||
|
|
| ||
| Replace the bobbin case. Contact |
| ||
noise is made | The bobbin case is scratched, or |
| ||
while | your retailer or the nearest authorized | – | ||
has a burr on it. | ||||
embroidering. | service center. |
| ||
|
| |||
|
|
|
| |
|
| Incorrect bobbins will not work |
| |
| A bobbin designed specifically for | properly. Only use a bobbin | page 24 | |
| this machine is not used. | designed specifically for this | ||
|
| |||
|
| machine. |
| |
|
|
|
| |
The thread does | The needle has not been raised to | Press the needle position button. | page 32 | |
not pass through | the correct position. | |||
|
| |||
the eye of the |
|
|
| |
The needle is incorrectly installed. | Correctly install the needle. | page 36 | ||
needle. | ||||
|
|
|
| |
| The thread tension is incorrect. | Adjust the tension of the upper | page 64 | |
| thread. | |||
The stitch is not |
|
| ||
|
|
| ||
| Remove the tangle thread. If the |
| ||
sewn correctly. | The thread is tangled, for example, |
| ||
| thread is tangled in the bobbin case, | page 70 | ||
| in the bobbin case. | |||
| clean the race. |
| ||
|
|
| ||
|
|
|
| |
The lamps do not | The lamps are damaged. | Contact your retailer or the nearest | – | |
authorized service center. | ||||
|
| |||
come on. |
|
|
| |
The machine is not turned on. | Turn on the machine. | page 19 | ||
| ||||
|
|
|
| |
Nothing appears | The brightness of the LCD is either | Adjust the brightness of the LCD. | page 81 | |
on the LCD. | too light or too dark. | |||
|
| |||
|
|
|
| |
Machine does not | An animation is displayed on the | Touch the LCD with your finger, and |
| |
operate when | page 20 | |||
LCD. | the animation will disappear. | |||
button is pressed. |
| |||
|
|
| ||
|
|
|
| |
Embroidery unit | No pattern selected. | Select a pattern. | page 49 | |
|
|
| ||
The embroidery unit is not set up |
|
| ||
does not move. | Set up the embroidery unit correctly. | page 15 | ||
| correctly. | |||
|
|
| ||
|
|
|
| |
Embroidering |
|
|
| |
continues | Dust has collected on the bobbin | Remove any dust from the bobbin |
| |
although the | page 70 | |||
thread sensor. | thread sensor. | |||
bobbin thread |
| |||
|
|
| ||
ran out. |
|
|
| |
|
|
|
|
76