KitchenAid 8574116 Secure dishwasher in cabinet opening, Complete installation

Page 20

Secure dishwasher in cabinet opening

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

1.If you have not already done so, open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This will prevent screws from falling into pump area when securing dishwasher to countertop.

2.Check that dishwasher is still level and centered side to side in the opening.

3.Secure dishwasher to countertop or sides of cabinet with two, #10 x 1/2" Phillips-head screws. The dishwasher must be secured to keep it from tipping when door is opened. Do not drop screws into bottom of dishwasher.

	screw to
OR	side cabinet
OR

screw to countertop

4.Open door about 3 inches (7.6 cm) and check that space between inner door and tub is equal on both sides. If spacing is not equal, loosen bracket screws and shift tub. Tighten bracket screws.

5.Check that top of door does not contact screws, brackets, or countertop. If it does, dishwasher must be lowered and re-leveled.

6.If securing to sides of cabinet, replace the plastic buttons.

plastic button

7.Remove towel from dishwasher.

8.Reinstall the lower dishrack.

Bottom sound pad installation (on some models)

1.Remove the bottom sound pad from inside the dishwasher and take it out of the plastic bag.

2.Place pad on the floor in front of the dishwasher, making sure lettering is facing up and vinyl pad faces down.

3.Fold up and hold the side panels down. Carefully slide the pad toward the back of the dishwasher as far as it will go, making sure not to push or pull any wires or hoses. (Do not force.) Side panels will open to proper position.

NOTE: If there are pipes or other obstructions coming up through the floor, you will need to cut a slit in the pad to fit around the obstacle.

4.Fold the front end of the pad up into position. Make sure the vinyl pad is tucked up behind the door and the dishwasher front legs, as shown.

Complete installation

1.Check that grounding clip is attached to the lower panel.

2.Place the lower panel behind the access panel. Some models have insulation on the access panel which must fall behind the insulation on the lower panel.

access panel

lower panel

grounding clip

20

Image 20

Contents Installation Instructions Undercounter Dishwasher You need to Dishwasher SafetyTable of Contents Installation Requirements All installationsAddition, for new installations Tools and PartsProduct dimensions Cutout dimensionsIf direct wiring dishwasher If connecting dishwasher with a power supply cordDrain Requirements Water Supply RequirementsInstallation Instructions Prepare cabinet opening using existing utility hookupsInstall the drain hose Option 1 Waste disposer with air gapOption1 Direct wire method Electrical connectionOption 2 No waste disposer with air gap Option 4 No waste disposer no air gapInstall the water line Option 2 Power supply cord methodInstall moisture barrier on some models Prepare dishwasher If you have built-up floorsInstall door panel-Pro Line series Install the door handle on some modelsInstall the door handle-Pro Line series Custom panel dimensions For dishwashers with the control panel shown belowInstall custom panel Option 1 For models KUDP02FSPA, KUDS02FSPA, KUDU02FSPAOption 2 For models KUDI02FR, KUDP02FR, KUDS02FR, KUDU02FR Option 3 For models KUDC02IR, KUDI02IR, KUDP02IR KUDS02IR Option 1 Countertop attachment Choose attachment optionOption 2 Dishwasher side attachment Level the dishwasher Check door spring tension Move dishwasher into cabinet opening Helpful Tip Option 1 Direct wire methodMake Electrical Connection Connect to water supply Connect to drainSecure dishwasher in cabinet opening Bottom sound pad installation on some modelsComplete installation Check operation If dishwasher does not operateTenir compte de ceci Sécurité du lave-vaisselleTable des matières Exigences d’installation Emplacement d’installationPour toutes les configurations d’installation Outillage et piècesDimensions du produit Dimensions de l’espace d’installationSpécifications de la canalisation d’évacuation Spécifications de l’alimentation en eauSpécifications électriques Pour le raccordement direct du lave-vaisselleOption 1 broyeur à déchets avec brise-siphon Instructions d’installationInstallation du tuyau d’évacuation Raccordement électrique Option 2 pas de broyeur à déchets avec brise-siphonOption 4 pas de broyeur à déchets sans brise-siphon Option 3 broyeur à déchets sans brise-siphonImportant Utiliser toujours un tuyau d’évacuation neuf Installation de la canalisation d’eauOption 2 raccordement par cordon d’alimentation Installation de la barrière contre lhumidité Préparation du lave-vaisselle Plancher rehaussé Installation de la poignée de porte Installation de la poignée de porte Série Pro LineInstallation du panneau de la porte- série Pro Line Dimensions du panneau personnaliséModèles KUDI02FR, KUDP02FR, KUDS02FR, KUDU02FR Installation du panneau personnalisé Option 1 Pour les modèles KUDP02FSPA, KUDS02FSPA, KUDU02FSPALes angles supérieurs du Placer délicatement le panneau externe à part Vis Option 1 Fixation sur le plan de travail Choix de la méthode d’immobilisation de l’appareilContrôle de la tension des ressorts de la porte Insertion du lave-vaisselle dans l’espace d’installation Établissement de l’aplomb du lave-vaisselleOption 1 Câblage direct Conseil utileRaccordement à la canalisation d’eau Raccordement à la canalisation d’évacuation Alimentation de l’appareil par câblage direct Installation du panneau d’insonorisationDernières opérations de l’installation Contrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctementImprimé aux É.-U