Frymaster FR2 manual Calibrate fryer

Page 8

Calibrate fryer (continued)

5Read oil temperature.

Insert the fry vat probe of the pyrometer into the hot oil to within 1 inch (2.5 cm) of the probe’s tip. The tip should be approximately 3 inches (7.6 cm) below the surface of the oil. Allow the temperature reading to stabilize.

6Display temperature on fryer.

Press the temperature display switch for the vat where you took the pyrometer reading.

The display will show the temperature for the vat.

7Compare temperature readings.

Compare the temperature reading on the pyrometer with the corresponding tempera- ture on the display.

If the two temperatures are less than 5°F (3°C) apart (ei- ther plus or minus), you do not need to adjust the tem- perature setting.

If the two temperatures are more than 5°F (3°C) apart (either plus or minus), call a service technician to report the problem.

8Repeat for other side of split- vat.

If the vat you tested was a full vat, skip this step and go to step 9.

If the vat you tested was one side of a split-vat, repeat steps 5 through 7 on the other side of the split-vat.

9End calibration check.

When you have finished steps 5 through 7 for the vat (in- cluding both sides of a split- vat), press the on/off button to end the calibration check for the vat.

10Calibrate remaining fryers.

Repeat steps 1 through 9 for all remaining fryers.

©McDonald’s Corporation · Planned Maintenance Manual · Revised June 2008

Page 2 of 2

Frymaster Fryer All models using an M2000 Computer

Bi-weekly

FR 2 B1

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Weekly maintenance task Bi-weekly maintenance taskMonthly maintenance task Quarterly maintenance tasksFR 2 D1 Shut off and disconnect gas FR 2 W1Remove and empty grease trough and cup Clean area behind fryers Prepare fryer for cleaningClean fryer filters Disconnect fryer from electricityClean area behind fryer Ask manager to inspectWash fryer legs and casters Mop floor around fryerTurn on gas supply Reinstall fryer filters and grease troughClean area behind other fryers Procedure Calibrate pyrometer FR 2 B1Turn on fryer and heat oil Check oil levelCalibrate fryer Turn fryer off ProcedureCheck most recent recovery time Calibrate fryer recovery time Adjust fryer, if necessaryCheck recovery time again Recalibrate all remaining fryersFrymaster Fryer All models using an M2000 Computer FR 2 Q1Boil out fry vats electric fryers only Allow solution to heat up Clean fry basketsClean basket support rack Start boil-outDrain solution from fryer Drain solution from vatFill vat with water Rinse and dry vatBoil-out remaining fryers Skim oilSeason baskets and racks Procedure Prepare for tests Put fryer into programming modeFR 2 Q2 Decide which vat to testTest second mechanical high-limit control Verify high-limit controlsTest the first internal high- limit control Verify high-limit controls for all remaining fryers Decide what to do if either control failedDiscard oil Procedure Prepare fryer for procedure Reinstall filter panFR 2 Q3 Replace O-ringFR 2 S1 Boil out fry vats gas fryers only Start boil-out Drain solution from fryer Boil out remaining fryers FR 2 A1-T Cabinet inspectionCheck regulated gas pressure Check combustionAnnual Inspection gas fryers only FR 2 A2-T Element inspectionTilt inspection Amp-draw checkWiring connection inspection Annual Inspection electric fryers onlyProbe check Electrical component inspection

FR2 specifications

The Frymaster FR2 is a state-of-the-art commercial deep fryer designed to meet the demands of busy kitchens while delivering high-quality frying performance. It embodies innovative technology and user-friendly features that aim to enhance efficiency and productivity in food preparation.

One of the standout features of the Frymaster FR2 is its compact design, which makes it suitable for various kitchen layouts, including those with limited space. Despite its smaller footprint, it is equipped with a dual frying tank system, allowing for increased frying capacity without compromising on performance. This design means that operators can efficiently cook multiple products simultaneously, thereby boosting output during peak hours.

The FR2 integrates advanced heating technology, utilizing a high-efficiency heating element that ensures rapid heat-up times and precise temperature control. This feature is crucial for achieving consistent frying results and maintaining the quality of the food. The fryer's temperature ranges from 200°F to 400°F, providing the versatility needed for frying a wide variety of foods, from crispy French fries to delicate seafood.

Safety and ease of use are paramount in the Frymaster FR2. The fryer is equipped with a built-in oil filtration system that extends the life of the cooking oil by removing food particles and impurities. This not only enhances the flavor and quality of fried foods but also reduces oil replacement costs, making it a cost-effective choice for busy kitchens.

In addition, the FR2 features an intuitive digital control panel, complete with programmable cooking timers and temperature readouts. This helps kitchen staff monitor cooking times effectively and ensure that items are fried to perfection. The fryer also includes an automatic shut-off feature, providing peace of mind and enhancing safety by preventing overheating.

Durability is another key characteristic of the Frymaster FR2. Constructed with high-quality stainless steel, it is designed to withstand the rigorous conditions of a commercial kitchen. Its sturdy build ensures longevity and minimizes maintenance needs, making it a reliable investment for any establishment.

In summary, the Frymaster FR2 is a high-performance commercial fryer offering vital features and technologies that make it perfect for modern kitchens. With its space-efficient design, efficient heating system, advanced filtration, and user-friendly controls, it stands out as a top choice for restaurateurs looking to enhance their frying capabilities while ensuring food quality and safety.
Top Page Image Contents