Frymaster 24G Series operation manual Supply Line Specifications

Page 20

24G SERIES FLATBOTTOM GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS

3.4 Gas Connections (cont.)

NATIONAL CODE REQUIREMENTS: NON-CE

This equipment is to be installed in compliance with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the U.S. Food and Drug Administration.

This equipment is manufactured to use the type of gas specified on the rating plate attached to the door. Connect equipment stamped "NAT" only to natural gas and that stamped "PRO" only to LP (Propane) gas.

Australia Only: Installation is to be in accordance with the requirements of AS5601/AG601, local regulatory authority requirements and other statutory regulations.

DANGER

Before connecting new pipe to this appliance, the pipe must be blown out thoroughly to remove all foreign material. Foreign material in the burner and gas controls will cause improper and dangerous operation.

Installation shall be made with a gas connector that complies with national and local codes.

Quick disconnect devices, if used, shall likewise comply with national and local codes.

DANGER

The fryer MUST be connected to the gas supply specified on the rating and serial number

plate located on the back of the fryer door.

The gas supply (service) line must be the same size or greater than the fryer inlet line. Dean 24G Series gas fryers are equipped with a 3/4" (22 mm) male ISO 7.1 inlet. The gas supply line must be sized to accommodate all gas-fired equipment connected to that gas supply. Consult local gas companies or suppliers, or your local contractor for minimum supply line requirements.

Supply Line Specifications

The gas supply lines must be sized as indicated in the chart below, based on the total number of fryers connected to the main gas supply.

Recommended Gas Supply Line Sizes

Gas Types

 

Number of Fryers

 

 

1

2 to 3

4 or more (*)

Natural Gas

3/4" (22 mm)

1" (28 mm)

1-1/4" (35 mm)

Propane Gas

1/2" (15 mm)

3/4" (22 mm)

1" (28 mm)

(*) When exceeding 18 feet (6 meters) for a configuration of more than four fryers, it is necessary to provide a 1 1/4" (35 mm) rigid gas connection.

3-5

Image 20
Contents Hour Service Hotline 1-800-551-8633 December Gas FryersPage Page Table of Contents Fryer Operations Service Information 24G Series Flatbottom GAS Fryers IntroductionApplicability and Validity Ordering PartsSafety Information Service PersonnelQualified Installation Personnel DefinitionsQualified Service Personnel 24G Series Flatbottom GAS Fryers Important Information Receiving and Unpacking EquipmentGeneral If your equipment arrives damagedFryer Description ModelRating Plate Automatic Safety FeaturesPrinciples of Operation Pre-Installation Equipment Installed at High Altitudes Installation StandardsAir Supply and Ventilation Temperature Conversion of Units CE SystemsPressure Heat Input24G Series Flatbottom GAS Fryers Installation Instructions Installing the FryerLeg and Caster Installation GeneralLegs Only Leg and Rigid Caster InstallationLeveling the Fryer Installing Optional Swivel Casters Rigid Casters OnlyGas Connections CE RequirementsSupply Line Specifications Recommended Gas Supply Line Sizes Gas Types Number of FryersRegulating Gas Pressure Rigid ConnectionsManual shut-off valve Gas Connections Gas Connections Adjustments/Adaptation To Different Gases GAS Supply for Which IT is not ConfiguredGas Inputs CE Units onlyGas Conversion Procedures Gas Type Orifice Part NumberGas Conversion Procedures Non-CE gas valve typical Gas Conversion Components Electrical ConnectionsContact factory at time Conversion24G Series Flatbottom GAS Fryers Fryer Operations Initial Start-upPilot Lighting Procedures, Standing Pilot CE Units OnlyOff position Pilot position On position Pilot Lighting Procedures, Electronic Ignition Systems Boil-Out Procedure Boil-Out Procedure Final Preparation Filling Fryer with Cooking Oil/Shortening24G Series Flatbottom GAS Fryers Controller Operation Operating Fryers with Thermatron ControllersPosition when in use 24G Series Flatbottom GAS Fryers Preventative Maintenance Weekly24G Series Flatbottom GAS Fryers Preventative Maintenance Periodic/Annual24G Series Flatbottom GAS Fryers Preventative Maintenance 24G Series Flatbottom GAS Fryers Troubleshooting Pilot Burner MalfunctionsMain Burner Malfunctions Thermatron Controller Calibration Recommended Spare Parts Service Hotline

24G Series specifications

The Frymaster 24G Series is a standout in the world of commercial fryers, designed specifically to meet the needs of high-demand kitchens. This series combines state-of-the-art technology with user-friendly features to deliver an exceptional frying experience. A key characteristic of the Frymaster 24G Series is its advanced frying performance, which allows operators to produce perfectly cooked food with superior quality.

One of the main features of the Frymaster 24G Series is its high-production capacity. The fryers are designed to handle large volumes of food, making them ideal for busy restaurants, fast food outlets, and catering operations. With a wide range of cooking oil options, including vegetable and fry oils, chefs have the flexibility to choose the right medium for their recipes, enhancing the flavor profiles of their dishes.

The 24G Series also boasts an innovative digital control system that allows for greater accuracy and consistency in cooking temperatures. This technology helps to ensure that food is fried evenly and to the desired crispness, which is crucial for maintaining quality in a competitive market. The programmable features enable operators to set specific frying times and temperatures, reducing the chance of overcooking or undercooking.

Energy efficiency is another hallmark of the Frymaster 24G Series. Designed with advanced heat exchange systems, these fryers maximize heat retention and minimize energy consumption, ultimately leading to reduced operational costs. The fryers also feature a reliable filtration system that prolongs oil life by removing food particles and impurities. This not only enhances food taste but also contributes to a healthier frying environment.

Safety is paramount in commercial kitchens, and the Frymaster 24G Series has incorporated multiple safety features, including automatic shut-off mechanisms and cool-to-the-touch exteriors. These safety measures help to protect both staff and customers, reducing the risks associated with high-temperature cooking.

In summary, the Frymaster 24G Series is a powerful and efficient solution for any commercial kitchen. Its combination of high production capacity, advanced digital controls, energy efficiency, and safety features makes it an ideal choice for those looking to elevate their frying operation. Whether frying appetizers, main courses, or desserts, the Frymaster 24G Series ensures consistently high-quality results every time.