Meat Probe
(on convection models)
WARNING
Burn Hazard
Use an oven mitt to remove temperature probe. Do not touch broil element.
Failure to follow these instructions can result in burns.
The meat probe accurately measures the internal temperature of meat, poultry and casseroles with liquid and should be used in determining the doneness of meat and poultry. It should not be used during full and center broiling, convection broiling, dehydrating or proofing bread.
Always unplug and remove the meat probe from the oven when removing food.
To Use:
Before using, insert the probe into the center of the thickest portion of meat or into the inner thigh or breast of poultry, away from fat or bone at an angle as shown in following diagram. Place food in oven. Using the handle of the probe, connect the meat probe to the jack. Keep probe as far away from heat source as possible. Close oven door.
A
B
A. Meat probe
B. Meat probe jack
1.Press MORE OPTIONS.
2.Use the right Quickset pad to scroll to MEAT PROBE.
3.Select MEAT PROBE using the left Quickset pad.
4.Set the desired internal food temperature by selecting one of the displayed temperatures or use the number pads to enter the temperature. The probe temperature can be set between 100°F and 185°F (38°C and 85°C).
If the meat probe is not inserted, INSERT PROBE will be displayed.
5.Select BAKE or CONVECT.
6.If CONVECT was selected, select CNVT BAKE, CNVT ROAST or CNVT PASTRY.
7.Set the oven temperature by selecting one of the displayed temperatures or use the number pads to enter the temperature.
The display will briefly show the selected temperatures for the oven and probe.
After 10 seconds, the display will show the actual oven temperature and actual probe temperature.
IMPORTANT: If the probe is removed from the oven receptacle at any time during the cooking process, the control will prompt INSERT PROBE. If the probe is not reinserted within 30 seconds, the program will be canceled and the oven will turn off.
8.When the selected internal temperature of the food has been reached, the oven will shut off and “PROBE END” appears on the display.
NOTE: To avoid overcooking the food, remove it from the oven as soon as the oven shuts off.
9.Using the handle of the probe, remove the probe from the jack. The probe will be hot. Hold probe with an oven mitt or pot holder when removing from the oven.
To Change Probe Temperature, Oven Setting:
Press CANCEL, then repeat previous steps.
After cooking, unplug the probe and remove food from oven.
See “General Cleaning” section to clean probe.
Drying
(on some models)
For best results, use a drying rack. A drying rack allows air to circulate evenly around the food.
The convection fan will operate during the drying procedure.
To Set Drying:
1.Open the oven door slightly. The oven door needs to be opened slightly to allow moisture to escape from the oven during the drying process.
2.Place the magnetic door spacer Part Number
A 
A. Magnetic door spacer
3.Gently close the door until the spacer magnet makes contact with the oven door. The magnet will hold the spacer in the proper position during the drying process and allows the door to be opened at any time during drying without losing proper positioning.
IMPORTANT: If the spacer is not placed correctly, the convection fan will not operate.
4.Press CONVECT.
5.Use the right Quickset pad to scroll to DRYING.
6.Select DRYING using the left Quickset pad.
7.Use the Quickset pads to select a displayed temperature or enter a temperature with the number pads. Temperatures can be set between 100°F and 200°F (38°C and 93°C).
8.“DRYING” and the temperature will be displayed. “PREHEAT” will be displayed until the programmed temperature is reached.
9.Press CANCEL when finished drying.
Follow the Drying Guide chart for drying times.
Check foods at minimum times given. Cool foods to room temperature before testing for doneness.
18