Jenn-Air JGS8860BD manual Description of Fault Codes for EOC, Control-Related Error not measurable

Page 13

Troubleshooting Procedures

!WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing, unless testing requires power and/or gas.

Description of Fault Codes for EOC III

Each fault code consists of 4 digits and is structured as follows:

 

 

 

 

 

 

 

 

1st (Leftmost) Digit:

2nd Digit: Alpha-Character

3rd Digit: Secondary

 

4th Digit : Oven

 

Primary Failure System

 

Failure Mechanism

 

Cavity Number

1

– Local to Control System

d – Diagnostic Failure (measurable)

 

 

1

– Upper (Single) Oven

3

– Sensor or Meat Probe

c Control-Related Error (not measurable)

 

 

2

– Lower Oven

4

– Input to Control System

 

 

 

c – Control System

9

– Door Lock

 

 

 

 

 

If a fault is detected, then one of the following three messages will be scrolled on the display:

FAULT DETECTED PRESS ENTER TO TRY AGAIN. This message displays when a fault is detected while a cooking function is active. Clear by pressing the Cancel keypad.

FEATURE NOT AVAILABLE. This message displays when a fault is detected while entering data during initial programming and also when a locked out function is detected. Clear by pressing any key.

FAULT DETECTED DISABLE POWER TO CLEAR. This message displays when a runaway temperature condition is detected while the control is in idle mode. Press any key to clear the message, but the fault remains until the control senses a Power-On reset.

Fault Code Chart

Fault

Description

Component to Troubleshoot/Replace

Code

 

 

1c1c

Shorted key.

Ensure ribbon cable is securely connected, inspect ribbon cable and

connector (shorts, breakage, corrosion, etc.). If OK, replace control.

 

 

1c2c

Membrane keyboard disconnected.

Ensure ribbon cable is securely connected, inspect ribbon cable and

connector (shorts, breakage, corrosion, etc.). If OK, replace control.

 

 

1c4c

Board – to – Board communication failure.

Replace control.

1c6c

EEPROM hardware fault.

Replace control.

1c7c

Control not calibrated.

Replace control.

1c8c

EEPROM CRC error – User Options.

Replace control.

1c81

EEPROM CRC error – Cook Profile.

Replace control.

1d11

Unlocked runaway temperature – 600° F

Ohm sensor and harness (see "Oven Sensor" chart). If OK, change

 

 

control.

1d21

Locked runaway temperature – 950° F

Ohm sensor and harness (see "Oven Sensor" chart). If OK, change

 

 

control.

3d11

Temperature sensor open.

Check connections, sensor (see "Oven Sensor" chart) and harness. If

 

 

OK, replace control.

3d21

Temperature sensor shorted.

Check connections, sensor (see "Oven Sensor" chart) and harness. If

 

 

OK, replace control.

3d41

Meat probe shorted.

Check probe jack and harness. If OK, check meat probe (see "Meat

 

 

Probe" chart).

3d51

Meat probe not calibrated.

Check probe jack and harness. If OK, check meat probe (see "Meat

 

 

Probe" chart).

4d11

Door switch not closed when locked.

Check connections, switch, harness, and motor. If OK, replace control.

4d21

No cooling fan rotation.

Check cooling fan motor and harness. If OK, replace control.

4d31

Cooling fan on when de-energized.

Check cooling fan motor and harness. If OK, replace control.

4d41

Cooling fan overspeed.

Check cooling fan motor and harness. If OK, replace control.

4d51

Door switch circuit fault.

Check connections, harness, and motor. If OK, replace control.

9d11

Latch will not lock.

Check wire connections. If OK, replace motorized door lock.

9d21

Latch will not unlock.

Check wire connections. If OK, replace motorized door lock.

9d31

Latch both locked and unlocked.

Check wire connections. If OK, replace motorized door lock.

© 2006 Maytag Services

16026923

13

Image 13
Contents Service Important Information Customer Service Support CenterTable of Contents Servicing Safety Practices for ServicerReceiving Oven Using the OvenProduct Safety Devices Connecting Range to GasBaking, Broiling, and Roasting Electrical RequirementsGeneral Information Placement of the Oven SpecificationsService Parts and AccessoriesGrounding ArningRange Description Troubleshooting Procedures Burner, but burner does not Control-Related Error not measurable Description of Fault Codes for EOCOven Sensor, Meat Probe and Cooling Fan Temperature Charts Gas on Illustration Component Test Procedure ResultsGas OFF Factory set to Natural GasJGS8850BD Control Component Test Procedure Illustration Component Test ProcedurePad Results Trace MeasurementPad Trace Control Component Test Procedure Pad ResultsSabbath Mode Oven Temperature AdjustmentClock & Day Display Disable 208/240 V SettingTimers Tones Feature Access Procedure Tone OptionsVolume Energy Saver ModeRelay Logic for EOC Quick Test Mode for EOC Description of Fault Codes for EOC Maintop Assembly Removal Select Models Cartridge Assembly Removal Select ModelsTop Burner Assembly Removal Select Models Lower Burner Assembly Removal Select ModelsManifold Assembly Removal Spark Module ReplacementBurner Switch Replacement Control Panel Assembly RemovalOven Sensor Replacement Cooling Fan ReplacementConvection Element Replacement Select Models Bake Burner and Ignitor RemovalOven Hi-Limit Thermostat Replacement Oven Light Bulb/Oven Light Socket ReplacementRegulator Removal Gas Valve Removal Select ModelsStorage Drawer Track Disassembly Select Models Oven Door Latch ReplacementStorage Drawer Disassembly Bottom Access Panel Removal Select ModelsWarming Drawer Track Disassembly Select Models Warming Drawer Hi-Limit Switch Replacement Select ModelsWarming Drawer Disassembly Oven Door DisassemblyOven Door, Warming Drawer Storage Drawer and Access Panel DisassemblyAppendix a Jenn-Air Updraft Gas Slide-In Range All Ranges can TIP and Cause Injuries to Persons Electric SupplyElectrical Supply Connection Gas Supply Follow these procedures to remove appliance for servicingCheck Pressure of House Piping System Clearance Dimensions Dégagements Dimensions/Dimensions/Dimensiones Use Lappareil Gas/À gaz/Gas Electric/Électrique/Eléctrica Appendix B USE & Care Guide Setting the controls Operating During a Power FailureSurface Controls Pilotless IgnitionSealed Burners CooktopHigh Performance Burner Low Turn Down BurnerVentilation System Care and Cleaning Ventilation SystemControl Panel Setting the ClockQuickset Pads ClockLocking the Control and Oven Door TimersConvect BakingBake Options Convect OptionsConvect Roast Convect BakeRapid Preheat Broil Broiling ChartTo set Broil More Options DelayCook & Hold ProofingMeat Probe Keep WarmTo select a recipe from the preset Recipe List Suggested Internal Food TemperaturesFavorites To Save the Last Recipe CompletedLanguage SetupAuto Convect Conversion Temp Adjust Sabbath ModeTo change the timer beeps To adjust the beepsTo change the volume of the beeps To turn off this featureAppendix C LP Propane Conversion Noir 27A Correct LP Propane Conversion Flip the regulator cap and replace the plastic Usted Debe iniciar el enroscado de las Reverse steps 6 through To reassemble oven30A 31A Correct BON Correcto Gas Conversion Instructions, JGS8850BD*, JGS8860BD Gas Conversion Instructions, JGS9900BD #50 42mm27 a Jaune Correct BON Correcto

JGS9900BD, JGS8860BD, JGS8850BD, JGS8750BD specifications

The Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD are a series of high-performance gas cooktops designed for culinary enthusiasts who value precision and sophistication. These models are distinguished by their robust construction, modern aesthetics, and a range of innovative features that streamline the cooking process.

One of the key features across these models is the professional-grade burners. The JGS8750BD, for instance, boasts a powerful 20,000 BTU burner, perfect for high-heat searing and rapid boiling. In contrast, the JGS8850BD offers a versatile 15,000 BTU burner, catering to a variety of cooking needs, including simmering and sautéing. For more delicate tasks, the JGS8860BD showcases a 5,000 BTU burner designed for simmering sauces and cooking delicate dishes with precision.

Another notable characteristic of these cooktops is the incorporation of the Jenn-Air® Turbo Flame™ technology. This feature provides an exceptional level of control, allowing chefs to achieve the desired temperature with accuracy. This technology is particularly valuable for those who require consistent heat for intricate recipes and techniques.

The seamless stainless-steel design not only elevates the appearance of any kitchen but also offers easy cleaning and maintenance. The high-quality grates found on these models are designed for durability and stability, ensuring pots and pans remain securely in place during cooking. Additionally, the continuous surface grates facilitate effortless sliding of cookware from one burner to another.

The JGS9900BD stands out with its advanced electronic ignition system, which ensures that the burners ignite quickly and reliably, minimizing downtime in the kitchen. Safety is also a priority across these models, featuring flame failure detection that automatically shuts off the gas supply if a flame goes out.

In terms of size, these cooktops cater to different kitchen configurations, with varying configurations to suit individual preferences and space constraints. Whether you're an avid home cook or a professional chef, the Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD combine superior technology with elegant design, making them a valuable addition to any modern kitchen. This series exemplifies Jenn-Air's commitment to quality, performance, and aesthetics, ensuring an elevated cooking experience for all users.