Jenn-Air JGS8860BD, JGS9900BD, JGS8750BD, JGS8850BD manual Arning, Grounding

Page 9

General Information

Grounding

NOTE: This appliance must be properly grounded, for personal safety.

Power cord on this appliance is equipped with a three- prong grounding plug. This matches standard three- prong grounding wall receptacle to prevent possibility of electric shock from this appliance.

Consumer should have wall receptacle and circuit checked by qualified electrician to verify receptacle is properly grounded.

It is the consumers responsibility to replace standard two- prong wall receptacles with properly grounded three-prong wall receptacles.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM POWER CORD.

For 15 amp circuits only, do not use an adapter on 20 amp circuit. Where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded two- prong wall receptacle by the use of a UL listed adapter (available at most hardware stores).

Larger slot on adapter must be aligned with larger slot in the wall receptacle to provide proper polarity.

!W ARNING

Attaching adapter ground terminal to wall receptacle cover screw does not ground appliance unless the cover screw is metal and not insulated, and wall receptacle is grounded through the house wiring. Consumer should have circuit checked by a qualified electrician to verify receptacle is properly grounded.

When disconnecting power cord from adapter, always hold adapter with one hand. If this is not done, adapter ground terminal is very likely to break with repeated use. Should this happen, DO NOT USE appliance until a proper ground has been established.

Neutral Wire

Ground Hot Line

NOTE: Circuit tester can be used to verify voltage at outlet. Connect one lead to hot line and the other lead to ground. Circuit tester should light.

© 2006 Maytag Services

16026923

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Service Important Information Customer Service Support CenterTable of Contents Servicing Safety Practices for ServicerReceiving Oven Using the OvenProduct Safety Devices Connecting Range to GasBaking, Broiling, and Roasting Electrical RequirementsGeneral Information Placement of the Oven SpecificationsService Parts and AccessoriesGrounding ArningRange Description Troubleshooting Procedures Burner, but burner does not Control-Related Error not measurable Description of Fault Codes for EOCOven Sensor, Meat Probe and Cooling Fan Temperature Charts Gas on Illustration Component Test Procedure ResultsGas OFF Factory set to Natural GasJGS8850BD Control Component Test Procedure Illustration Component Test ProcedurePad Results Trace MeasurementPad Trace Control Component Test Procedure Pad ResultsSabbath Mode Oven Temperature AdjustmentClock & Day Display Disable 208/240 V SettingTimers Tones Feature Access Procedure Tone OptionsVolume Energy Saver ModeRelay Logic for EOC Quick Test Mode for EOC Description of Fault Codes for EOC Maintop Assembly Removal Select Models Cartridge Assembly Removal Select ModelsTop Burner Assembly Removal Select Models Lower Burner Assembly Removal Select ModelsManifold Assembly Removal Spark Module ReplacementBurner Switch Replacement Control Panel Assembly RemovalOven Sensor Replacement Cooling Fan ReplacementConvection Element Replacement Select Models Bake Burner and Ignitor RemovalOven Hi-Limit Thermostat Replacement Oven Light Bulb/Oven Light Socket ReplacementRegulator Removal Gas Valve Removal Select ModelsStorage Drawer Track Disassembly Select Models Oven Door Latch ReplacementStorage Drawer Disassembly Bottom Access Panel Removal Select ModelsWarming Drawer Track Disassembly Select Models Warming Drawer Hi-Limit Switch Replacement Select ModelsWarming Drawer Disassembly Oven Door DisassemblyOven Door, Warming Drawer Storage Drawer and Access Panel DisassemblyAppendix a Jenn-Air Updraft Gas Slide-In Range Electric Supply All Ranges can TIP and Cause Injuries to PersonsElectrical Supply Connection Follow these procedures to remove appliance for servicing Gas SupplyCheck Pressure of House Piping System Clearance Dimensions Dégagements Dimensions/Dimensions/Dimensiones Use Lappareil Gas/À gaz/Gas Electric/Électrique/Eléctrica Appendix B USE & Care Guide Setting the controls Operating During a Power FailureSurface Controls Pilotless IgnitionSealed Burners CooktopHigh Performance Burner Low Turn Down BurnerVentilation System Care and Cleaning Ventilation SystemControl Panel Setting the ClockQuickset Pads ClockLocking the Control and Oven Door TimersConvect BakingBake Options Convect OptionsConvect Bake Convect RoastRapid Preheat Broiling Chart BroilTo set Broil More Options DelayCook & Hold ProofingMeat Probe Keep WarmTo select a recipe from the preset Recipe List Suggested Internal Food TemperaturesFavorites To Save the Last Recipe CompletedSetup LanguageAuto Convect Conversion Temp Adjust Sabbath ModeTo change the timer beeps To adjust the beepsTo change the volume of the beeps To turn off this featureAppendix C LP Propane Conversion Noir 27A Correct LP Propane Conversion Flip the regulator cap and replace the plastic Usted Debe iniciar el enroscado de las Reverse steps 6 through To reassemble oven30A 31A Correct BON Correcto Gas Conversion Instructions, JGS8850BD*, JGS8860BD Gas Conversion Instructions, JGS9900BD #50 42mm27 a Jaune Correct BON Correcto

JGS9900BD, JGS8860BD, JGS8850BD, JGS8750BD specifications

The Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD are a series of high-performance gas cooktops designed for culinary enthusiasts who value precision and sophistication. These models are distinguished by their robust construction, modern aesthetics, and a range of innovative features that streamline the cooking process.

One of the key features across these models is the professional-grade burners. The JGS8750BD, for instance, boasts a powerful 20,000 BTU burner, perfect for high-heat searing and rapid boiling. In contrast, the JGS8850BD offers a versatile 15,000 BTU burner, catering to a variety of cooking needs, including simmering and sautéing. For more delicate tasks, the JGS8860BD showcases a 5,000 BTU burner designed for simmering sauces and cooking delicate dishes with precision.

Another notable characteristic of these cooktops is the incorporation of the Jenn-Air® Turbo Flame™ technology. This feature provides an exceptional level of control, allowing chefs to achieve the desired temperature with accuracy. This technology is particularly valuable for those who require consistent heat for intricate recipes and techniques.

The seamless stainless-steel design not only elevates the appearance of any kitchen but also offers easy cleaning and maintenance. The high-quality grates found on these models are designed for durability and stability, ensuring pots and pans remain securely in place during cooking. Additionally, the continuous surface grates facilitate effortless sliding of cookware from one burner to another.

The JGS9900BD stands out with its advanced electronic ignition system, which ensures that the burners ignite quickly and reliably, minimizing downtime in the kitchen. Safety is also a priority across these models, featuring flame failure detection that automatically shuts off the gas supply if a flame goes out.

In terms of size, these cooktops cater to different kitchen configurations, with varying configurations to suit individual preferences and space constraints. Whether you're an avid home cook or a professional chef, the Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD combine superior technology with elegant design, making them a valuable addition to any modern kitchen. This series exemplifies Jenn-Air's commitment to quality, performance, and aesthetics, ensuring an elevated cooking experience for all users.
Top Page Image Contents