Jenn-Air JGS8860BD Warming Drawer Hi-Limit Switch Replacement Select Models, Oven Door Removal

Page 29

Disassembly Procedures

To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas.

Warming Drawer Hi-Limit Switch

Replacement (Select Models)

1.Remove unit from installation position, see “Removing and Replacing Range” procedure.

2.Remove front side trim, see "Front Side Trim Removal" procedure.

3.Remove warming drawer, see "Warming Drawer Removal (Select Models)" procedure.

4.Remove screws securing side panel to oven chassis.

5.Remove screws securing hi-limit switch to warming drawer support frame.

6.Label and disconnect hi-limit switch wire terminals.

7.Remove hi-limit switch from outside the warming drawer support frame.

NOTE: Do not pull hi-limit switch and wiring through cavity wall.

8.Reverse procedure to reinstall warming drawer hi- limit switch.

Oven Door Removal

!WARNING

To avoid risk of personal injury or property damage, do not lift oven door by the handle.

1.Open oven door slightly and grasp door on both sides.

2.Lift up and off the hinge receivers.

3.Reverse procedure to reinstall oven door.

Warming Drawer Track Disassembly (Select Models)

1.Remove warming drawer, see "Warming Drawer Removal (Select Models)" procedure.

2.Place door on a protected surface.

3.Remove screws securing front panel to glass panel.

4.Remove screws front panel to warming drawer.

5.Remove screws securing "sliding tracks" to warming drawer.

6.Reverse procedure to reassemble warming drawer.

Warming Drawer Disassembly

1.Remove warming door, see "Warming Drawer Removal (Select Models)" procedure.

2.Place door on a protected surface.

3.Remove screws securing front panel to glass panel.

4.Remove screws securing front panel to warming drawer.

5.Remove screws securing "sliding tracks" to warming drawer.

6.Reverse procedure to reassemble oven door.

NOTE: See page 30 for illustration.

Oven Door Disassembly

1.Remove oven door, see "Oven Door Removal" procedure.

2.Place door on a protected surface.

3.Remove screws securing door glass to oven door trim and frame (screws located along the top and bottom edge of oven door).

NOTE: Proceed with the following steps if replacing door handle.

4.Remove screws securing door handle to door glass.

5.Remove screws securing upper and lower shields.

6.Remove screws securing door baffle.

7.Remove oven door insulation.

8.Remove screws securing outer and inner door glass (and glass frame).

9.Remove oven door liner, if replacing.

10.Reverse procedure to reassemble oven door.

NOTE: See page 30 for illustration.

© 2006 Maytag Services

16026923

29

Image 29
Contents Service Important Information Customer Service Support CenterTable of Contents Servicing Safety Practices for ServicerReceiving Oven Using the OvenProduct Safety Devices Connecting Range to GasBaking, Broiling, and Roasting Electrical RequirementsGeneral Information Placement of the Oven SpecificationsService Parts and AccessoriesGrounding ArningRange Description Troubleshooting Procedures Burner, but burner does not Control-Related Error not measurable Description of Fault Codes for EOCOven Sensor, Meat Probe and Cooling Fan Temperature Charts Gas on Illustration Component Test Procedure ResultsGas OFF Factory set to Natural GasJGS8850BD Control Component Test Procedure Illustration Component Test ProcedurePad Results Trace MeasurementPad Trace Control Component Test Procedure Pad ResultsSabbath Mode Oven Temperature AdjustmentClock & Day Display Disable 208/240 V SettingTimers Tones Feature Access Procedure Tone OptionsVolume Energy Saver ModeRelay Logic for EOC Quick Test Mode for EOC Description of Fault Codes for EOC Maintop Assembly Removal Select Models Cartridge Assembly Removal Select ModelsTop Burner Assembly Removal Select Models Lower Burner Assembly Removal Select ModelsManifold Assembly Removal Spark Module ReplacementBurner Switch Replacement Control Panel Assembly RemovalOven Sensor Replacement Cooling Fan ReplacementConvection Element Replacement Select Models Bake Burner and Ignitor RemovalOven Hi-Limit Thermostat Replacement Oven Light Bulb/Oven Light Socket ReplacementRegulator Removal Gas Valve Removal Select ModelsStorage Drawer Track Disassembly Select Models Oven Door Latch ReplacementStorage Drawer Disassembly Bottom Access Panel Removal Select ModelsWarming Drawer Track Disassembly Select Models Warming Drawer Hi-Limit Switch Replacement Select ModelsWarming Drawer Disassembly Oven Door DisassemblyOven Door, Warming Drawer Storage Drawer and Access Panel DisassemblyAppendix a Jenn-Air Updraft Gas Slide-In Range Electrical Supply Connection Electric SupplyAll Ranges can TIP and Cause Injuries to Persons Check Pressure of House Piping System Follow these procedures to remove appliance for servicingGas Supply Clearance Dimensions Dégagements Dimensions/Dimensions/Dimensiones Use Lappareil Gas/À gaz/Gas Electric/Électrique/Eléctrica Appendix B USE & Care Guide Setting the controls Operating During a Power FailureSurface Controls Pilotless IgnitionSealed Burners CooktopHigh Performance Burner Low Turn Down BurnerVentilation System Care and Cleaning Ventilation SystemControl Panel Setting the ClockQuickset Pads ClockLocking the Control and Oven Door TimersConvect BakingBake Options Convect OptionsRapid Preheat Convect BakeConvect Roast To set Broil Broiling ChartBroil More Options DelayCook & Hold ProofingMeat Probe Keep WarmTo select a recipe from the preset Recipe List Suggested Internal Food TemperaturesFavorites To Save the Last Recipe CompletedAuto Convect Conversion SetupLanguage Temp Adjust Sabbath ModeTo change the timer beeps To adjust the beepsTo change the volume of the beeps To turn off this featureAppendix C LP Propane Conversion Noir 27A Correct LP Propane Conversion Flip the regulator cap and replace the plastic Usted Debe iniciar el enroscado de las Reverse steps 6 through To reassemble oven30A 31A Correct BON Correcto Gas Conversion Instructions, JGS8850BD*, JGS8860BD Gas Conversion Instructions, JGS9900BD #50 42mm27 a Jaune Correct BON Correcto

JGS9900BD, JGS8860BD, JGS8850BD, JGS8750BD specifications

The Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD are a series of high-performance gas cooktops designed for culinary enthusiasts who value precision and sophistication. These models are distinguished by their robust construction, modern aesthetics, and a range of innovative features that streamline the cooking process.

One of the key features across these models is the professional-grade burners. The JGS8750BD, for instance, boasts a powerful 20,000 BTU burner, perfect for high-heat searing and rapid boiling. In contrast, the JGS8850BD offers a versatile 15,000 BTU burner, catering to a variety of cooking needs, including simmering and sautéing. For more delicate tasks, the JGS8860BD showcases a 5,000 BTU burner designed for simmering sauces and cooking delicate dishes with precision.

Another notable characteristic of these cooktops is the incorporation of the Jenn-Air® Turbo Flame™ technology. This feature provides an exceptional level of control, allowing chefs to achieve the desired temperature with accuracy. This technology is particularly valuable for those who require consistent heat for intricate recipes and techniques.

The seamless stainless-steel design not only elevates the appearance of any kitchen but also offers easy cleaning and maintenance. The high-quality grates found on these models are designed for durability and stability, ensuring pots and pans remain securely in place during cooking. Additionally, the continuous surface grates facilitate effortless sliding of cookware from one burner to another.

The JGS9900BD stands out with its advanced electronic ignition system, which ensures that the burners ignite quickly and reliably, minimizing downtime in the kitchen. Safety is also a priority across these models, featuring flame failure detection that automatically shuts off the gas supply if a flame goes out.

In terms of size, these cooktops cater to different kitchen configurations, with varying configurations to suit individual preferences and space constraints. Whether you're an avid home cook or a professional chef, the Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD combine superior technology with elegant design, making them a valuable addition to any modern kitchen. This series exemplifies Jenn-Air's commitment to quality, performance, and aesthetics, ensuring an elevated cooking experience for all users.