Jenn-Air JGS9900BD, JGS8860BD, JGS8750BD, JGS8850BD manual Jaune

Page 72

Gas Conversion Instructions, JGS9900BD*

30

31

Turn on gas and electrical

supply to product.

Ouvrez le gaz et l'électricité alimentant l'appareil.

Abra el suministro de gas y conecte el suministro eléctrico al producto.

NOTE: When reversing an LP conversion back to natural gas, the LP choke in step 29 MUST be removed.

REMARQUE : Lorsque vous faites une reconversion du GPL au gaz naturel, l’étrangleur pour GPL de l’étape 29 DOIT être retiré.

NOTA: Cuando revierta una conversión de gas LP para usar gas natural, DEBE retirar el obturador de gas LP en el paso 29.

Replace burner caps. Replace grates./Remettez les chapeaux de brûleur. Remettez les grilles./Vuelva a instalar las tapas de los quemadores. Vuelva a instalar las rejillas.

Low Flow Adjustment/Réglage bas débit/Ajuste del flujo minimo

32

NOTE: Repeat steps 33-35 for single burners./

REMARQUE : Répétez les étapes 33 à 35 pour les

brûleurs simples./NOTA: Repita los pasos 33 a 35

para los quemadores sencillos.

33

Adjust each single surface burner one at a time. Light

burner and turn to lowest setting. Remove knob./ Ajustez chaque brûleur de surface simple un par un. Allumez le brûleur et réglez-le au niveau le plus bas. Retirez le bouton./Ajuste los quemadores superiores sencillos uno a la vez. Encienda el quemador y ajústelo al nivel más bajo. Retire la perilla.

34

1/8" Flat head

Screwdriver/

Tournevis à lame

plate de 1/8 po/

Destornillador de

1/8” de cabeza plana

Hold knob stem in LOW position. Insert screwdriver to

engage screw./Tenez la tige du bouton en position

LOW. Introduisez le tournevis pour tourner la

vis./Mantenga la varilla de la perilla en el ajuste ‘LOW’ (Bajo). Inserte el destornillador en el tornillo.

35

Adjust flame height with screwdriver./Ajustez la hauteur de la flamme avec le tournevis./Ajuste la altura de la llama con el destornillador.

38

Insert screwdriver to engage screw./Introduisez le tournevis pour tourner la vis./Inserte el destornillador en el tornillo.

36

NOTE: Double burner only./REMARQUE : Brûleur

double uniquement./NOTA: Quemador doble

solamente.

39

Adjust flame height with screwdriver./Ajustez la hauteur de la flamme avec le tournevis./Ajuste la altura de la llama con el destornillador.

37

Adjust double surface burner. Light burner and turn to lowest setting where both inner and outer ring are lit.

Remove knob./Ajustez le brûleur de surface double. Allumez le brûleur et réglez-le au niveau le plus bas où les deux cercles (intérieur et extérieur) sont allumés. Retirez le bouton./Ajuste el quemador superior doble. Encienda el quemador y ajústelo al nivel más bajo en el que se encienden los anillos interior y exterior. Retire la perilla.

40

CORRECT

 

BON

 

CORRECTO

 

YELLOW

1/4"

JAUNE

 

AMARILLA

BLUE LIFTING

FLAMME BLEUE SE SOULEVANT

AZUL QUE SE SEPARA DEL QUEMADOR

Verify proper flame height and appearance./Vérifiez la taille des flammes et leur apparence./Verifique la altura y apariencia correctas de la llama.

C – 16

16026923

© 2006 Maytag Services

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Service Customer Service Support Center Important InformationTable of Contents Safety Practices for Servicer ServicingUsing the Oven Receiving OvenConnecting Range to Gas Product Safety DevicesBaking, Broiling, and Roasting Electrical RequirementsGeneral Information Specifications Placement of the OvenService Parts and AccessoriesArning GroundingRange Description Troubleshooting Procedures Burner, but burner does not Description of Fault Codes for EOC Control-Related Error not measurableOven Sensor, Meat Probe and Cooling Fan Temperature Charts Illustration Component Test Procedure Results Gas onGas OFF Factory set to Natural GasJGS8850BD Illustration Component Test Procedure Control Component Test ProcedurePad Results Trace MeasurementControl Component Test Procedure Pad Results Pad TraceOven Temperature Adjustment Sabbath ModeClock & Day Display Disable 208/240 V SettingFeature Access Procedure Tone Options Timers TonesVolume Energy Saver ModeRelay Logic for EOC Quick Test Mode for EOC Description of Fault Codes for EOC Cartridge Assembly Removal Select Models Maintop Assembly Removal Select ModelsTop Burner Assembly Removal Select Models Lower Burner Assembly Removal Select ModelsSpark Module Replacement Manifold Assembly RemovalBurner Switch Replacement Control Panel Assembly RemovalCooling Fan Replacement Oven Sensor ReplacementConvection Element Replacement Select Models Bake Burner and Ignitor RemovalOven Light Bulb/Oven Light Socket Replacement Oven Hi-Limit Thermostat ReplacementRegulator Removal Gas Valve Removal Select ModelsOven Door Latch Replacement Storage Drawer Track Disassembly Select ModelsStorage Drawer Disassembly Bottom Access Panel Removal Select ModelsWarming Drawer Hi-Limit Switch Replacement Select Models Warming Drawer Track Disassembly Select ModelsWarming Drawer Disassembly Oven Door DisassemblyStorage Drawer and Access Panel Disassembly Oven Door, Warming DrawerAppendix a Jenn-Air Updraft Gas Slide-In Range Electric Supply All Ranges can TIP and Cause Injuries to PersonsElectrical Supply Connection Follow these procedures to remove appliance for servicing Gas SupplyCheck Pressure of House Piping System Clearance Dimensions Dégagements Dimensions/Dimensions/Dimensiones Use Lappareil Gas/À gaz/Gas Electric/Électrique/Eléctrica Appendix B USE & Care Guide Operating During a Power Failure Setting the controlsSurface Controls Pilotless IgnitionCooktop Sealed BurnersHigh Performance Burner Low Turn Down BurnerCare and Cleaning Ventilation System Ventilation SystemSetting the Clock Control PanelQuickset Pads ClockTimers Locking the Control and Oven DoorBaking ConvectBake Options Convect OptionsConvect Bake Convect RoastRapid Preheat Broiling Chart BroilTo set Broil Delay More OptionsCook & Hold ProofingKeep Warm Meat ProbeSuggested Internal Food Temperatures To select a recipe from the preset Recipe ListFavorites To Save the Last Recipe CompletedSetup LanguageAuto Convect Conversion Sabbath Mode Temp AdjustTo adjust the beeps To change the timer beepsTo change the volume of the beeps To turn off this featureAppendix C LP Propane Conversion Noir 27A Correct LP Propane Conversion Flip the regulator cap and replace the plastic Reverse steps 6 through To reassemble oven Usted Debe iniciar el enroscado de las30A 31A Correct BON Correcto Gas Conversion Instructions, JGS8850BD*, JGS8860BD Gas Conversion Instructions, JGS9900BD 42mm #5027 a Jaune Correct BON Correcto

JGS9900BD, JGS8860BD, JGS8850BD, JGS8750BD specifications

The Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD are a series of high-performance gas cooktops designed for culinary enthusiasts who value precision and sophistication. These models are distinguished by their robust construction, modern aesthetics, and a range of innovative features that streamline the cooking process.

One of the key features across these models is the professional-grade burners. The JGS8750BD, for instance, boasts a powerful 20,000 BTU burner, perfect for high-heat searing and rapid boiling. In contrast, the JGS8850BD offers a versatile 15,000 BTU burner, catering to a variety of cooking needs, including simmering and sautéing. For more delicate tasks, the JGS8860BD showcases a 5,000 BTU burner designed for simmering sauces and cooking delicate dishes with precision.

Another notable characteristic of these cooktops is the incorporation of the Jenn-Air® Turbo Flame™ technology. This feature provides an exceptional level of control, allowing chefs to achieve the desired temperature with accuracy. This technology is particularly valuable for those who require consistent heat for intricate recipes and techniques.

The seamless stainless-steel design not only elevates the appearance of any kitchen but also offers easy cleaning and maintenance. The high-quality grates found on these models are designed for durability and stability, ensuring pots and pans remain securely in place during cooking. Additionally, the continuous surface grates facilitate effortless sliding of cookware from one burner to another.

The JGS9900BD stands out with its advanced electronic ignition system, which ensures that the burners ignite quickly and reliably, minimizing downtime in the kitchen. Safety is also a priority across these models, featuring flame failure detection that automatically shuts off the gas supply if a flame goes out.

In terms of size, these cooktops cater to different kitchen configurations, with varying configurations to suit individual preferences and space constraints. Whether you're an avid home cook or a professional chef, the Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD combine superior technology with elegant design, making them a valuable addition to any modern kitchen. This series exemplifies Jenn-Air's commitment to quality, performance, and aesthetics, ensuring an elevated cooking experience for all users.
Top Page Image Contents