Jenn-Air JGS9900BD, JGS8860BD, JGS8750BD Removing and Replacing Range, Front Side Trim Removal

Page 24

Disassembly Procedures

To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas.

Removing and Replacing Range

1.Turn off power and remove gas supply from unit.

2.Slide range forward from installation position.

3.Unplug power cord and disconnect gas line from unit.

4.Disconnect downdraft blower motor and remove flex ducting to the blower and range (select models).

NOTE: To avoid countertop damage, do not move range forward until range has been raised enough to clear all cabinetry.

5.Pull the range forward out of the cabinet opening.

6.Disconnect or unplug the power cord leading from unit to fuse box or junction box depending on unit.

7.Replace the oven using the installation instructions and anti-tip bracket(s).

Front Side Trim Removal

1.Remove power from unit.

2.Slide unit out far enough to access side trim.

3.Remove screws securing front side trim piece(s) to oven chassis (left and right trim pieces).

4.Gently grasp trim piece with both hands, pull forward and roll trim piece off retainer clips.

5.Reverse procedure to reinstall front side trim piece(s).

Cartridge Assembly Removal

(Select Models)

Cooktop cartridges are installed on the left side of the range cooktop.

1.Remove power from unit.

2.Lift up on the tab (located on the cartridge) until top of cartridge clears the opening on the range by 2 inches.

NOTE: Lifting the cartridge too high while still engaged in the receptacle could damage the terminal plug.

3.Hold cartridge by the sides and slide away from terminal receptacle.

4.Lift cartridge out when fully unplugged.

Install cartridges here

Maintop Assembly Removal (Select Models)

1.Remove power from unit.

2.Remove range from installation position, see “Removing and Replacing Range” procedure.

3.Remove front side trim, see "Front Side Trim Removal" procedure.

4.Remove air grill, grill grates, filter, aeration pan and cartridges (cartridge models).

5.Remove cartridge receptacles and grill pans (cartridge models).

6.Remove screws from plenum area at front of main top cartridge opening (cartridge models).

7.Remove screws securing top burner assembly to lower burner assembly.

8.Label and disconnect wire terminals to ignitors.

9.Remove perimeter screws securing main top to chassis.

10.Gently lift main top away from chassis.

11.Reverse procedure to reinstall maintop assembly.

Top Burner Assembly Removal (Select Models)

1.Disconnect power before servicing.

2.Remove screws securing burner top assembly to lower assembly.

3.Label and remove wire terminals to ignitor.

4.Reverse procedures to reassemble.

Lower Burner Assembly Removal (Select Models)

1.Remove top burner, see "Top Burner Assembly Removal (Select Models)" procedure.

2.Disconnect tubing from lower assembly.

3.Reverse procedures to reassemble.

NOTE: Perform gas leak test.

24

16026923

© 2006 Maytag Services

Image 24
Contents Service Customer Service Support Center Important InformationTable of Contents Safety Practices for Servicer ServicingUsing the Oven Receiving OvenConnecting Range to Gas Product Safety DevicesBaking, Broiling, and Roasting Electrical RequirementsGeneral Information Specifications Placement of the OvenService Parts and AccessoriesArning GroundingRange Description Troubleshooting Procedures Burner, but burner does not Description of Fault Codes for EOC Control-Related Error not measurableOven Sensor, Meat Probe and Cooling Fan Temperature Charts Illustration Component Test Procedure Results Gas onGas OFF Factory set to Natural GasJGS8850BD Illustration Component Test Procedure Control Component Test ProcedurePad Results Trace MeasurementControl Component Test Procedure Pad Results Pad TraceOven Temperature Adjustment Sabbath ModeClock & Day Display Disable 208/240 V SettingFeature Access Procedure Tone Options Timers TonesVolume Energy Saver ModeRelay Logic for EOC Quick Test Mode for EOC Description of Fault Codes for EOC Cartridge Assembly Removal Select Models Maintop Assembly Removal Select ModelsTop Burner Assembly Removal Select Models Lower Burner Assembly Removal Select ModelsSpark Module Replacement Manifold Assembly RemovalBurner Switch Replacement Control Panel Assembly RemovalCooling Fan Replacement Oven Sensor ReplacementConvection Element Replacement Select Models Bake Burner and Ignitor RemovalOven Light Bulb/Oven Light Socket Replacement Oven Hi-Limit Thermostat ReplacementRegulator Removal Gas Valve Removal Select ModelsOven Door Latch Replacement Storage Drawer Track Disassembly Select ModelsStorage Drawer Disassembly Bottom Access Panel Removal Select ModelsWarming Drawer Hi-Limit Switch Replacement Select Models Warming Drawer Track Disassembly Select ModelsWarming Drawer Disassembly Oven Door DisassemblyStorage Drawer and Access Panel Disassembly Oven Door, Warming DrawerAppendix a Jenn-Air Updraft Gas Slide-In Range Electric Supply All Ranges can TIP and Cause Injuries to PersonsElectrical Supply Connection Follow these procedures to remove appliance for servicing Gas SupplyCheck Pressure of House Piping System Clearance Dimensions Dégagements Dimensions/Dimensions/Dimensiones Use Lappareil Gas/À gaz/Gas Electric/Électrique/Eléctrica Appendix B USE & Care Guide Operating During a Power Failure Setting the controlsSurface Controls Pilotless IgnitionCooktop Sealed BurnersHigh Performance Burner Low Turn Down BurnerCare and Cleaning Ventilation System Ventilation SystemSetting the Clock Control PanelQuickset Pads ClockTimers Locking the Control and Oven DoorBaking ConvectBake Options Convect OptionsConvect Bake Convect RoastRapid Preheat Broiling Chart BroilTo set Broil Delay More OptionsCook & Hold ProofingKeep Warm Meat ProbeSuggested Internal Food Temperatures To select a recipe from the preset Recipe ListFavorites To Save the Last Recipe CompletedSetup LanguageAuto Convect Conversion Sabbath Mode Temp AdjustTo adjust the beeps To change the timer beepsTo change the volume of the beeps To turn off this featureAppendix C LP Propane Conversion Noir 27A Correct LP Propane Conversion Flip the regulator cap and replace the plastic Reverse steps 6 through To reassemble oven Usted Debe iniciar el enroscado de las30A 31A Correct BON Correcto Gas Conversion Instructions, JGS8850BD*, JGS8860BD Gas Conversion Instructions, JGS9900BD 42mm #5027 a Jaune Correct BON Correcto

JGS9900BD, JGS8860BD, JGS8850BD, JGS8750BD specifications

The Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD are a series of high-performance gas cooktops designed for culinary enthusiasts who value precision and sophistication. These models are distinguished by their robust construction, modern aesthetics, and a range of innovative features that streamline the cooking process.

One of the key features across these models is the professional-grade burners. The JGS8750BD, for instance, boasts a powerful 20,000 BTU burner, perfect for high-heat searing and rapid boiling. In contrast, the JGS8850BD offers a versatile 15,000 BTU burner, catering to a variety of cooking needs, including simmering and sautéing. For more delicate tasks, the JGS8860BD showcases a 5,000 BTU burner designed for simmering sauces and cooking delicate dishes with precision.

Another notable characteristic of these cooktops is the incorporation of the Jenn-Air® Turbo Flame™ technology. This feature provides an exceptional level of control, allowing chefs to achieve the desired temperature with accuracy. This technology is particularly valuable for those who require consistent heat for intricate recipes and techniques.

The seamless stainless-steel design not only elevates the appearance of any kitchen but also offers easy cleaning and maintenance. The high-quality grates found on these models are designed for durability and stability, ensuring pots and pans remain securely in place during cooking. Additionally, the continuous surface grates facilitate effortless sliding of cookware from one burner to another.

The JGS9900BD stands out with its advanced electronic ignition system, which ensures that the burners ignite quickly and reliably, minimizing downtime in the kitchen. Safety is also a priority across these models, featuring flame failure detection that automatically shuts off the gas supply if a flame goes out.

In terms of size, these cooktops cater to different kitchen configurations, with varying configurations to suit individual preferences and space constraints. Whether you're an avid home cook or a professional chef, the Jenn-Air JGS8750BD, JGS8850BD, JGS8860BD, and JGS9900BD combine superior technology with elegant design, making them a valuable addition to any modern kitchen. This series exemplifies Jenn-Air's commitment to quality, performance, and aesthetics, ensuring an elevated cooking experience for all users.